METHVEN 01-8284 User manual

Methven Australia Pty Ltd
ABN 15 104 813 390
Melbourne, Australia
www.methven.com
Max 40mm
32 - 46mm
Cold
Hot
InletIMPORTANT
Please read all of the instructions before installation
MA018284
Waipori 3 Hole Hob Mounted Set
Basin: 01-8284
Bath: 01-8307
Illustration Only
Use of this product is recommended for domestic and commercial applications.
Domestic and commercial warranty terms and conditions vary. Please refer to the Methven website
for full warranty terms and conditions - www.methven.com
All pipework must be thoroughly flushed prior to the installation of the mixer.
Inline filter washers must be installed on both hot and cold supplies to prevent foreign particles
damaging the ceramic head works.
Do not remove the ceramic head works from the mixer when installing.
Damage caused by hydrostatic testing is not covered by Methven’s warranty.
Methven recommends a licensed plumber carry out all installations in compliance with
the requirements of AS/NZS 3500. This product complies with AS/NZS 3718 regulations.
April 2012
Installation Guide
www.methven.com
Customer Care Hotline: 1300 METHVEN (638 483)
Email: [email protected].com
WMKA21005
2.5mm Hex key
Connected to Spout for
01-8284
Connected to T-piece
for 01-8307
Applies to basin
mixer only
MA018284 Waipori 3 Hole Hob Mounted Set AU.indd 1 2/05/12 2:33 PM

THE METHVEN GUARANTEE
The warranty statement shall apply to all tapware & showers supplied by Methven
For more information visit www.methven.com
THIS WARRANTY ISSUED BY: Methven Australia Pty Ltd, Melbourne Australia
Technical Specification
Inlet Connections: All 1/2" BSP
Operating Pressure: 150kPa - 500kPa
For optimum performance hot and cold water pressures should be equal.
AS/NZS 3500 stipulates a 500kPa maximum operating pressure at any outlet
within a building. Where normal pressure exceeds 500kPa, a pressure limiting
valve must be installed.
This basin mixer set is rated at 7.5l/m. If limited water flow is experienced, locate
stream shaper flow restricting device and filter washers and clean away
foreign material as required.
Operating Temperature: Recommended hot water supply 50°C, maximum 70°C. AS/NZS 3500 requires all
hot water supplies to any sanitary fitting to be tempered to 50°C.
Ceramic cartridges: Warranty claims will be void where the ceramic head works has malfunctioned due
to the presence of the following within the water supply:
Copper tube pieces
Plastic pieces
Sand, dirt or stones
Thread tape
Other objects not normally present in the potable water supplies
www.methven.com
Customer Care Hotline: 1300 METHVEN (638 483)
Email: [email protected].com
1
2
3
4
7
5
11
13
12
Hot
Grub screw
& cap
Cold
Body assembly
O-ring
Mounting
gasket
Mounting
plate
Push fit inlet connector
(bath only)
Base ring
O-ring
Stream shaper
(ASDA)
T-piece
2.5mm hex key Spout
Handle
Handle plate
1/2” BSP
Lock nut
Product Components
Please check every component in accordance
with the table below
No. Item description Qty supplied
1 Spout 1
2Push fit inlet connector (bath only) 1
3 Base ring (spout) 1
4 O-ring 3
5 1/2" BSP 1
6 Mounting gasket 1
7 Mounting plate 1
8 Handle with grub screw & cap 2
9 Lock nut 2
10 Half dome/handle plate 2
11 Body assembly 1
12 2.5mm hex key 1
13 T-piece 1
6
8
9
10
4
04-9905
Hot 04-9752
Standard Spindle &
Handle Assembly Set Up
Spindle Handle
Extension 04-9837
Spindle Flange M x F
Extension 04-9875
SPARE PARTS
(NOT INCLUDED)
(NOT INCLUDED)
(NOT INCLUDED)
Cold 04-9769
Handle Parts / Assembly Care and Cleaning
Never use abrasives to clean this
product. Clean regularly with
contamination free warm soapy
water and a damp soft cloth.
Damage caused by using unsuitable
cleaning agents is not covered by
warranty.
MA018284 Waipori 3 Hole Hob Mounted Set AU.indd 2 2/05/12 2:33 PM