METHVEN AURAJET User manual

Methven warrants this product against manufacturing defects and that it is suitable for use
under the general operating conditions specified in this instruction sheet. However, regional
regulations apply and may affect your warranty. Please refer to www.methven.com or call
customer service for full details.
New Zealand
0800 804 222
Australia
1300 638 483
UK
0800 1 95 1602
www.methven.com
Care and Cleaning:
439949 ISSUE A
Technical Specifications:
Operating Pressure:
Min: 100kPa/1.0bar
Max: 500kPa/5bar*
Operating Temperature:
Hot: Max 70°C*
Cold: Min 5°C
Inlet Connections:
All ½" BSP
* Regional specific regulations apply.
Please refer to your warranty statement at
www.methven.com
Installation Guide
AURAJET™ SHOWER SYSTEM
Optimum: 150kPa/1.5bar - 500kPa/5bar
1
2
Run hot water through shower for 2 minutes before first use.
Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with warm
soapy water and a damp soft cloth.
Clean filter washer located in the shower hose and in the overhead shower periodically. To access
filter washer in overhead shower, push down on release button, hold the elbow bracket and pull
shower head away from it.
Remove filter washer from the shower head waterway
by gently levering out with a small screwdriver.
If shower performance is compromised by the build-up of lime-scale, soak in limescale remover for
up to 10 minutes. Do not attempt to remove limescale with sharp objects or abrasives. Do not use
products containing chlorine bleach or hydrochloric acid as these can damage the shower. Always
rinse the shower thoroughly after cleaning to remove cleaning products that can damage the shower.
Refer to instructions above for how to remove overhead shower from elbow bracket.
Never insert objects into the spray slot or attempt to remove spray cover as this may cause damage
to shower components.
Do not hang any items or pull down on the overhead shower. This may cause damage to the
overhead shower.

Fit overhead shower into elbow bracket
and push firmly until the clips engage.
Inlet
Connector
Handset
Flat Washer
Swivelling Cone
Hose End
Filter Washer
• Methven recommends this product is
installed by a licensed plumber in
compliance with all relevant regional
regulations.
20±2mm
26mm max
Step 2
Firmly push the shower rail onto the
top inlet connector and bottom
railconnector.
Step 3
Step 4
Fit the elbow cover into the back of the elbow
bracket.
Clip into the elbow bracketand overhead
shower.
•
•
•
•
1800mm (Recommended)
785mm
FLOOR
Step 1
Install a ½” BSP nipple at the recommended
height.
•
Overhead
Rail
Hose
Inlet
Bottom Rail
Connector
Water Inlet
Elbow Cover
Handset
Step 6
Make sure a washer is in both ends of the
shower hose.
Screw one end of the hose to the bottom of
the shower rail, attach handset and place firmly
in holder.
•
•
It is the responsibility of the installer to
ensure a waterproof seal is achieved
between the product and mounting
surface. If in doubt about the quality of
the seal, remove the product and
reinstall using silicone to ensure a seal is
achieved.
All pipe work must be thoroughly flushed
prior to the installation of the hose.
After installation all connections must be
checked for leaks.
All outlets used primarily for personal
hygiene shall deliver water at a safe
temperature as per regional regulations.
•
•
•
IMPORTANT: Please read all of the instructions and turn off water
supply before installation.
General:
•
2
1
Secure in place by tightening the grub
screws firmly using the hex key provided.
•
Shower
Shower
Connector
Bottom Rail
Connector
•
Screw the bottom rail connector to a
wall stud vertically in line with the
inlet connector and at the correct
distance.
•
• Wall lining hole should be cut or
finished as per the dimension
shown in the diagram on the right.
Cut off the threaded nipple 20±2mm
from the wall lining and apply thread
seal tape to ensure a good seal.
•
Screw the inlet connector onto the
nipple ensuring that the o-ring is
sufficiently compressed to create
a watertight seal.
•
Step 5
To adjust slider position, rotate the slider
handle to unlock and lock the slider as shown.
•
Unlock
Lock
Ensure o-ring is located on the inlet
connector.
•