Metra Electronics 99-7013 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7013
99-7013
APPLICATIONS
Mitsubishi Outlander
2007-2010
KIT FEATURES
•DIN Radio Provision with Pocket
•ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
•Stacked ISO Mount Units Provision
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
•E) Double DIN Trim Plate • F) Snap In Pocket
Harness & Antenna Connections (sold seperately)
70-7005 - Mitsubishi Harness 07-up
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Set
1-800-221-0932
©COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
CD
TOOLS REQUIRED:
EF

Dash Disassembly
- Mitsubishi Outlander 2007-2010. . . . . . . . . . . . . . . . . . . . 1,2
Kit Preparation ...........................................3
Kit Assembly
- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
-ISO Mount Radio Provision with Pocket ....................... 5
-Double DIN/Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . 6
Final Assembly ...........................................7
TABLE OF CONTENTS
99-7013
*Note:
Refer also to the instructions included with the aftermarket radio.

99-7013 DASH DISASSEMBLY
MITSUBISHI OUTLANDER 2007-2010
PASSENGER
AIRBAG OFF
PASSENGER
PASSENGER
AIRBAG OFF
PASSENGER
B
C
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove the vents from the
left and right side of the factory radio
panel. ( Figure A)
Remove (4) Phillips screws securing
the radio chassis. Unplug and remove
the chassis. (Figure C)
2
Remove (2) Phillips screws securing
the radio trim panel then unclip and
remove the panel. (Figure B)
3
4
A
Continued on page 2.

99-7013 DASH DISASSEMBLY
MITSUBISHI OUTLANDER 2007-2010
2
Remove the labels from the front of
the radio trim panel at each side of
the hazardswitch by pushing them
out from behind the panel. (Retain the
labels to be reused during kit prepa-
ration) (
Figure F)
6
E
F
Continued to kit preparation.
REMOVE
“9” PHILLIPS SCREWS
(RETAIN SCREWS)
D
Remove (7) Phillips screws securing
the hazard switch assembly to the
back of the factory radio trim panel.
Unplug the ribbon cable from the
hazard switch assembly and remove
assembly from panel from rear.
(Retain the screws and switch
assembly to be reused during kit
preparation) (
Figure D,E)
5

99-7013 KIT PREPARATION
3
Secure the hazard switch panel into the radio housing using the factory hardware
removed previously and apply labels from the front of the factory radio trim panel to
front of the Metraradio panel.
(Figure A,B)
5
Continue to kit assembly.
A
PASSENGER
AIRBAG OFF
PASSENGER
B
MITSUBISHI OUTLANDER 2007-2010

4
99-7013 KIT ASSEMBLY
A
B
C
DIN RADIO PROVISION WITH POCKET
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.
(Figure A)
1
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
2
Snap the pocket into the radio housing.
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7013 KIT ASSEMBLY
5
B
C
D
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the after-
market radio using the screws sup-
plied with the radio.
(Figure A)
1
Slide the radio into the Radio Housing
until it snaps into place. (Figure B)
2
Snap the Trim Plate onto the front of
the Radio Housing. (Figure C)
3
Snap the pocket into the Radio
Housing. (Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A

99-7013 KIT ASSEMBLY
6
B
C
DOUBLE DIN/STACKED ISO UNITS PROVISION
Cut and remove the center bar from
the Radio Housing. (Figure A)
1
Snap the Double DIN Brackets to the
inside edge of the Radio Housing.
(Figure B)
2
Slide the Double DIN or stacked ISO
unit(s) into the bracket/radio housing
assembly and secure the Double DIN
or stacked ISO unit(s) to the assembly
using the screws supplied with the
unit(s).
(Figure C)
3
Snap the Double DIN Trim Plate onto
the front of the Radio Housing.
(Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A

7
99-7013 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
METRA / EIA WIRING CODE
12V Ignition / Acc..........Red
12V Batt / Memory. . . . . . . . . Yellow
Ground..................Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer.................Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.

99-7013
NOTES
8