Metra Electronics 99-3014G User manual

Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 4/23/19 INST99-3014G
INSTALLATION INSTRUCTIONS
99-3014G
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted gunmetal gray
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) Phillips screws (8)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32” socket wrench • Cutting tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly
–ISO DIN radio provision with pocket ..................4
–ISO DDIN radio provision .....................................5
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Please visit metraonline.com
for wiring harness options
Antenna Adapter: 40-EU55
A B C D
Chevrolet Silverado / GMC Sierra 2014-up
Visit MetraOnline.com for more detailed information about the product and up-to-date
vehicle specific applications
APPLICATIONS
Chevrolet
Silverado 1500.................2014-2018
Silverado 1500/2500..........2015-up
Silverado 1500 LD.....................2019
GMC
Sierra 1500.......................2014-2018
Sierra 2500/3500................2015-up
Sierra 1500 Limited...................2019

1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unclip and remove the trim panel
surrounding the radio/climate control
panel. (Figure A)
2. Remove (4) 9/32” screws securing the
radio/climate control panel, then unclip,
unplug and remove the panel. (Figure B)
(Figure A) (Figure C)
(Figure B) (Figure D)
3. Remove (2) 9/32” screws securing the
CD player. Slide the CD player out, then
unplug and remove the CD player.
(Figure C)
4. Unclip and slide out the Onstar module
and tuner box, then unplug and remove
them. (Figure D)
Continue to Kit Preparation
Tuner box
Onstar module

REV. 4/23/2019 INST99-3014G 3
KIT PREPARATION
(Figure A) (Figure B)
1. Cut the sub-dash to allow room for the
aftermarket radio. (Figure A)
2. Relocate the OnStar module lower in the
sub-dash where the factory CD player
was installed to allow room for the
aftermarket radio. (Figure B)
Continue to Kit Assembly

1.800.221.0932
|
MetraOnline.com
4
KIT ASSEMBLY
ISO DIN radio provision
1. Secure the radio brackets to the pocket
using (4) Phillips screws supplied.
(Figure A)
2. Secure the bracket/pocket assembly to
the radio trim panel using (4) Phillips
screws supplied. (Figure B)
3. Slide the radio between the radio
brackets, then secure using screws
supplied with the radio. (Figure C)
(Figure A) (Figure C)
(Figure B) (Figure D)
4. Clip the factory climate controls into the
radio trim panel. (Figure D)
5. Locate the factory wiring harness and
antenna connector in the dash. Metra
recommends using the proper mating
adapter from Metra or AXXESS. Complete
all connections to the radio and vehicle,
then test the radio and vehicle for
proper operation.
6. Reassemble the dash in reverse order of
disassembly to complete the installation.

REV. 4/23/2019 INST99-3014G 5
KIT ASSEMBLY
(Figure A) (Figure B) (Figure C)
ISO DDIN radio provision
1. Secure the radio brackets to the radio
trim panel using (4) Phillips screws
supplied. (Figure A)
2. Slide the radio between the radio
brackets, then secure using screws
supplied with the radio. (Figure B)
3. Clip the factory climate controls into the
radio trim panel. (Figure C)
4. Locate the factory wiring harness and
antenna connector in the dash. Metra
recommends using the proper mating
adapter from Metra or AXXESS. Complete
all connections to the radio and vehicle,
then test the radio and vehicle for
proper operation.
5. Reassemble the dash in reverse order of
disassembly to complete the installation .

1.800.221.0932
|
MetraOnline.com
6

REV. 4/23/2019 INST99-3014G 7

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 4/23/19 INST99-3014G
INSTALLATION INSTRUCTIONS
99-3014G
If you are having difficulties with the installation
of this product, contact our Tech Support line
either by phone at 1-800-253-TECH, or email at
[e-mail]. Before
doing so, look over the instruction booklet a
second time and ensure that the installation was
performed exactly as the instruction booklet
is stated. Have the vehicle apart and ready to
perform troubleshooting steps before contacting
Metra/Axxess Tech Support.

INSTRUCCIONES DE INSTALACIÓN
99-3014G
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 4/23/19 INST99-3014G
¡PRECAUCIÓN! Todos los accesorios, interruptores,
paneles de controles de clima y especialmente las
luces del indicador de las bolsas de aire deben estar
conectados antes ciclar la ignición. Además, no
quite el radio de fábrica con la llave en la posición o
de encendido ni con el vehículo funcionando.
CARACTERÍSTICAS DEL KIT
• Provisión de radio ISO DIN con cavidad
• Provisión de radio doble DIN
• Pintura en gris bronce de cañón
COMPONENTES DEL KIT
• A) Panel de moldura para radio • B) Soportes para radio • C) Cavidad • D) Tornillos Phillips (8)
HERRAMIENTAS REQUERIDAS
• Herramienta para quitar paneles
• Destornillador Phillips • Llave del tubo de 9/32”
• Herramienta para cortar
Chevrolet Silverado / GMC Sierra 2014 y mas
Visite MetraOnline.com para las aplicaciones específicas del vehículo hasta la fecha.
CABLEADO Y CONEXIONES DE ANTENA
(se venden por separado)
Arnés de cables: Por favor visite metraonline.com
para opciones de mazo de cables
Adaptador de antena: • 40-EU55
APLICACIONES
Chevrolet
Silverado 1500.................2014-2018
Silverado 1500/2500.....2015 y mas
Silverado 1500 LD.....................2019
GMC
Sierra 1500.......................2014-2018
Sierra 2500/3500...........2015 y mas
Sierra 1500 Limited...................2019
A B C D
INDICE
Desmontaje del tablero ........................................2
Preparación del kit .................................................3
Ensamble del kit
– Provisión de radio ISO DIN con cavidad ............4
–Provisión de radio doble DIN ..............................5

1.800.221.0932
|
MetraOnline.com
2
DESMONTAJE DEL TABLERO
1. Desenganche y quite el panel de
moldura que rodea el panel del radio/
control del clima. (Figura A)
2. Quite los (4) tornillos de 9/32” que
sujetan el radio/panel de control del
clima. (Figura B)
(Figura A) (Figura C)
(Figura B) (Figura D)
3. Quite los (2) tornillos de 9/32” que
sujetan el reproductor de CD y luego
desconecte y quite el reproductor.
(Figura C)
4. Desenganche y deslice hacia fuera el
módulo Onstar y la caja sintonizadora,
luego desconecte y retírelos. (Figura D)
Continuar la preparación del kit
Caja de sintonizador
Módulo onstar