Metra Electronics 99-8225G User manual

INSTALLATION INSTRUCTIONS FOR PART 99-8225G
99-8225G
APPLICATIONS
Toyota Venza
2009-2010
KIT FEATURES
•DIN Head Unit Provision With Pocket
•ISO DIN Head Unit Provision With Pocket
•Painted to match factory dash - G=Gray
•A) Single DIN Radio Housing • B) ISO Brackets • C) Trim Plate
KIT COMPONENTS
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Set
•Magnetized Universal Swivel Head Socket Adapter
1-800-221-0932
©COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
A
TOOLS REQUIRED:
B C
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
•70-1761 - 1987-up Toyota harness
• TYTO-01 - 2003-up Toyota JBL amp interface

Dash Disassembly
- Toyota Venza 2009-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly
-DIN Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . . .2
-ISO Din Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . 3
TABLE OF CONTENTS
99-8225G
*Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.
Metrarecommends MECP
certified technicians.

99-8225G DASH DISASSEMBLY
Toyota Venza 2009-2010
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove the trim panel to
the right of the shifter. ( Figure A)
2
Remove (1) Phillips screw from the
bottom of the climate control then
unclip and remove the climate
control.
(Figure B)
3
Remove (4)10 MM bolts securing the
radio. Note: You will need a univer-
sal swivel head socket adapter to
get to the bottom left bolt.
(Figure C)
4
Remove (4) Phillips screws securing
the factory radio to the a/c vent
panel. ( Figure D)
5
A
B
C
REAR VIEW - RADIO AND A/C VENT PANEL
RADIO
D
Continue to kit assembly.

99-8225G KIT ASSEMBLY
2
REAR VIEW - A/C VENT PANEL
A
B
C
D
Secure the Radio Housing into the
factory a/c vent panel using the
factory hardware.
(Figure A)
1
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure B)
3
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2
Slide the aftermarket head unit into
the cage and secure. (Figure C)
4
*Note: Refer also to the instructions included with the aftermarket radio.
DIN HEAD UNIT PROVISION WITH POCKET
Reassemble remaining radio and
dash assemblies in reverse order of
disassembly.
5
6
Snap the factory vent panel/Radio
Housing over dash cavity. (Figure D)

99-8225G KIT ASSEMBLY
3
REAR VIEW - A/C VENT PANEL
A
B
C
D
Secure the Radio Housing into the
factory a/c vent panel using the
factoryhardware. (Figure A)
1
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure B)
2
Slide the head unit into the radio
opening until the side clips engage.
(Figure C)
3
Snap the Trim Plate into the Radio
Housing. (Figure C)
4
*Note: Refer also to the instructions included with the aftermarket radio.
ISO DIN HEAD UNIT PROVISION WITH POCKET
5
Snap the factory vent panel/Radio
Housing over dash cavity.
(Figure D)
Reassemble remaining radio and
dash assemblies in reverse order of
disassembly.
6

99-8225G
NOTES
4

99-8225G
NOTES
5

99-8225G INSTRUCTIONS
REV. 05/20/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-8225G
www.metraonline.com
1-800-221-0932