Metra Electronics 99-7860 User manual

99-7860
1-800-221-0932 • www.metraonline.com
COPYRIGHT© 2002 METRA ELECTRONICS CORPORATION
KIT COMPONENTS
INSTALLATION INSTRUCTIONS
Honda Civic SI 2002
VEHICLE APPLICATIONS
uble DIN •
implate
using •
Trimplate •
• ISO Snap in
Brackets(2)
•Phillips screwdriver
•Offset tool
TOOLS REQUIRED
KIT FEATURES
•DIN head unit
provision with pocket
•ISO head unit
provision with pocket
•Stacked ISO head
unit provision
•Double DIN head unit
provision
Questions?
Call the Help Line:
(800)253 TECH
T997860
081302

99-7860
1
DASH DISASSEMBLY
1Disconnect the negative
battery terminal to
prevent an accidental
short circuit.
2Remove the shift knob
and unsnap the shifter
lever trim panel.
3Using and offset tool
remove (2) lower bolts
securing the center
panel.
4Unsnap and remove the
dash trim bezel and
disconnect the wiring.
5Remove (3) phillips
screws securing the
climate control pod to
the back of the dash
trim bezel and remove
the pod.
6Remove (4) phillips
screws from each side
securing the factory head
unit and pocket to the
bracket assembly
and remove.
NOTE: Removing the glove
box and the driver's side
lower trim panel may
be necessary when
removing the shifter
level trim panel when not
using an offset tool.
99-7860 • Honda Civic SI 2002
99-7860
TABLE OF CONTENTS
•Dash Disassembly
•Kit Features
• DIN Head Unit Provision with Pocket Assembly
• ISO Head Unit Provision with Pocket Assembly
• Double DIN Head Unit Provision Assembly
• Stacked ISO Head Unit Provision Assembly
•Final Assembly

99-7860
3
Align the holes in the ISO Snap-In
Brackets with the holes in the head
unit and mount the brackets to the
head unit with the screws supplied
with the unit.
See figure A
Slide the head unit/bracket assem-
bly into the radio opening until the
side clips engage.
See figure B
Snap the ISO trimplate over the
head unit.
See figure C
ISO HEAD IUNIT PROVISION WITH POCKET
1
3
2
99-7860 • Honda Civic SI 2002
NOTE: To remove the mounted head unit,
unclip and remove the ISO Trimplate. Using
a small flat-blade screwdriver, disengage
the side clips securing the ISO Snap In
Brackets to the housing/pocket assembly.
A
B
C
Assembled Kit
Snap the housing assembly into
the dash trim bezel.
4
99-7860
2
DIN HEAD UNIT PROVISION WITH POCKET
Slide the DIN cage into the radio
opening of the Housing and
secure by bending the metal
locking tabs down.
See figure A
Slide the DIN unit into the cage
until it is secure.
See figure B
1
2
A
B
99-7860 • Honda Civic SI 2002
Assembled Kit
Snap the housing assembly into
the dash trim bezel.
3

5
Snap the Double DIN Trimplate
over the head unit.
See figure B
STACKED ISO HEAD UNIT PROVISION
6
5A
B
Align the holes on the factory
bracket assembly with the holes on
the aftermarket ISO head units and
mount with the screws supplied
with the units.
See figure A
99-7860 • Honda Civic SI 2002
Assembled Kit
99-7860
4
DOUBLE DIN HEAD UNIT PROVISION
1
2
3
Align the holes on the factory
bracket assembly with the holes
on the aftermarkert Double DIN
head unit and mount with the
screws supplied with the unit.
See figure A
Cut and remove the center rib
(SHADED) from the Double DIN
Trimplate.
See figure B
Snap the Double DIN Trimplate
over the head unit.
See figure C
99-7860 • Honda Civic SI 2002
A
B
C
Assembled Kit

99-7860
6
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
FINAL ASSEMBLY
A
B
C
D
99-7860 • Honda Civic SI 2002
A
Locate the factory wiring harness in the dash.
Metra recommends using the proper mating
adaptor (70-1721) and making connections as
shown. (Isolate and individually tape off the
ends of any unused wires to prevent electrical
short circuit).
See figure A
1
Re-connect the battery terminal and test the
unit for proper operation.
2
Reassemble dash in the reverse order of page 1
in the Dash Disassembly.
3