Middle Atlantic Products C5-D Series User manual

C5-D SERIES
DEEP CREDENZA RACK
assembly instructions
THANK YOU
PRODUCT FEATURES
- Built-in thermostatically controlled cooling
- 14 rackspaces per bay
- Factory installed casters
Thank you for purchasing the C5-D Series Deep Credenza Rack. Please read all instructions thoroughly
before assembling this product.
WARNING: Instructions for C5-D Series accessories MUST be read thoroughly prior to following
these instructions. Please see the accessory-specific instructions for details on proper assembly.
I-00565 Rev -
- Rack frame ships separate to allow for equipment integration before finished surfaces are attached

Page 2
KICKPLATE INSTALLATION
1) Install the Kickplate by aligning screws into place using keyholes on credenza frame.
FRONT VIEW
REAR VIEW
Kickplate secures into place
when shifted in direction of arrow

Page 3
SIDE PANEL INSTALLATION
NOTE: For accessories related to the Side Panels, please read those instructions thoroughly before
continuing with the installation below
2) Install Side Panels by placing the four pre-installed hooks into the four slots on the frame. (FIGURE A)
(FIGURE A)
NOTE: When installing side panels, ensure door hinge plates are located at the front of the frame.
Door Hinge Plate

Page 4
TOP SURFACE INSTALLATION
NOTE: For accessories related to the Top Surface, please read those instructions thoroughly before
continuing with the installation below
3) Attach Top Surface to the frame using provided screws. Extra screws provided. (FIGURE B)
NOTE: Flat edge of Top Surface is designated as the rear.
(FIGURE B)
(Side Panel removed for clarity)
Number of #10 x 5/8” Screws Used Per Credenza Configuration
3-Bay 12
2-Bay 8
1-Bay 4
Conguration Screws

Page 5
DOOR INSTALLATION ONTO SIDE PANEL
4) Install doors using provided screws (two places per door) as shown. Extra screws provided.
(FIGURE C)
NOTE: All Doors may be installed to swing open from either left or right.
(FIGURE C)
Factory Installed Bumpers
(NOTE: (6) Six replacement bumpers supplied)

Page 6
DOOR INSTALLATION ONTO MULLION
5) Door to be installed onto credenza frame using provided screws (two places per door) as shown.
(FIGURE D)
(FIGURE D)
(Additional Sides and Doors removed for clarity)

Page 7
HINGE ADJUSTMENTS
Side Adjustment: Adjusts horizontal placement of door. Adjusts door-to-door gap
- Rotate screw clockwise or counterclockwise (+/-0.06 in) [+/-1.5 mm]
1
Height Adjustment: Adjusts vertical height of door
- Loosen to align door, then tighten (+/-0.08 in) [+/-2 mm]
2
Depth Adjustment: Adjusts the space between the door and the face of the frame of credenza
- Achievable through cam adjustment (+0.1/-0.02 in) [+2.5/-0.5 mm]
3
3
2
1
NOTE:
Directional adjustments apply to the door in the closed position. Hinge adjustment is done with door in
open position. Refer to (FIGURE E) for appropriate adjustments
Door in open position
2
1
3
(FIGURE E)
1

Page 8
HANDLE/KNOB INSTALLATION
(FIGURE G)
LACER BAR RELOCATION
Pre-installed Lacer Bars can be relocated on frame by removing screws as shown. (FIGURE G)
(Contemporary Handle - 2 screws) (Traditional Knob - 1 screw)
(FIGURE F)
6) Depending on credenza style (traditional or contemporary), handles and knobs are installed into
pre-drilled holes shown in the figures provided. (FIGURE F)
NOTE: A secondary mounting hole is
provided for when front rail is set back.

Page 9
DIMENSIONS
24 5/8”
[625 mm]
3-Bay 2-Bay
1-Bay Door
1-Bay
Top Surface
2-Bay
Top Surface
3-Bay
Top Surface
21 7/8”
[555 mm]
1 1/8”
[28 mm]
Side Panel
3/4”
[19 mm]
1” [25 mm]
1 1/8”
[28 mm]
1 1/8”
[28 mm]
28 1/8”
[714 mm] 65 3/4”
[1670 mm]
30 1/4”
[768 mm]
28 1/8”
[714 mm] 21 1/32” [534 mm]
30 1/4”
[768 mm]
31 1/4”
[794 mm]
69 1/2”
[1765 mm]
24 3/4” [629 mm]
31 1/4”
[794 mm]
28 1/8”
[714 mm] 43 3/8”
[1102 mm]
30 1/4”
[768 mm]
31 1/4”
[794 mm] 47 1/8”
[1197 mm]
29 3/8”
[746 mm]
30 3/16”
[767 mm]

Page 10
FAN NOTES
A) POWER CONNECTOR: Connects to a 12V 1A power supply (supplied).
B) TEMPERATURE PROBE: Temperature detection probe, five feet long.
NOTE: Blue LED in exhaust area illuminates when the unit is receiving power.
TURN ON TEMPERATURE: The blower will turn on at 87° F (30.5° C) and run proportionately
speed increases with temperature from 87° F (30.5° C) to 95° F (35° C). At 95° F and above,
the blower will run at full speed. The blower will stop running at 85° F (29.4° C).
WARRANTY
Middle Atlantic Products (the "Company") warrants the C5-D Series Deep Credenza Rack to be free from defects in material or workmanship under normal use and conditions for the lifetime of the product,
and the fans for (3) years from the date of shipment by the company.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of and
refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after inspection
thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or any modification or alteration of the products. In addition, this warranty
does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE
OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER
PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY.
Corporate Headquarters Middle Atlantic Canada Factory Distribution
Corporate Voice 973-839-1011 - Fax [phone] Voice 613-836-2501 - Fax [phone] USA: NJ - CA - IL Canada: ON - BC
International Voice [phone] - Fax [phone] middleatlantic.ca - [email protected]
middleatlantic.com - [email protected]
At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
30% Recycled Paper
(B)
(A)