Middle Atlantic Products C5 SERIES CREDENZA RACK User manual

C5 SERIES
Shelf System Insert
installation instructions
THANK YOU
Thank you for purchasing the C5 Series Shelf System Insert. Please read these instructions
thoroughly before installing this product.
(DOOR REMOVED FOR CLARITY)
I-00682 Rev A
HARDWARE LIST
7MMX50MM HEX
HEAD SCREW
QTY
DOWEL QTY
8
5/32 ALLEN KEY QTY
POWER DRIVER BIT QTY
1
TOOLS REQUIRED
• Power Driver
• #2 Phillips bit
12
10X5/8 PAN HEAD
PHILLIPS SCREW QTY
4
1
QTY
1
MOUNTING BRACKET
QTY
2
10X32X.5 PHILLIPS SCREW
3/16 ALLEN WRENCH QTY
1

Page 2
FIGURE A
STEP 1 STEP 2
STEP 3 STEP 4
ASSEMBLY
12
4
SCREWS (2) 7MMX50MM
HEX HEAD
SIDE
TOP
SCREWS (2) 7MMX50MM
HEX HEAD
SCREWS (4) 7MMX50MM
HEX HEAD
SCREWS (4) 7MMX50MM
HEX HEAD
1) Assemble the Shelf Insert using (12) 7MMX50MM Hex Head Screws in the sequence shown below.
(FIGURE A) NOTE: Do not overtighten.
1
2
TOP
SIDE SIDE
TOP
REAR
SIDE
REAR
BOTTOM
SIDE

1) Remove the front rackrail.
2) Remove the rear access panel.
3) Insert the mounting bracket into the slot on the bottom of the bay. Tilt the bracket slightly so that
factory installed rivnuts go underneath the slot.
4) Align the rivnuts with the second outer holes. (FIGURE B)
5) Affix mounting bracket using provided 10X32X.5 Phillips screws. (FIGURE C)
SHELF SYSTEM INSTALLATION
FIGURE B
FIGURE C
Page 3
Mounting
Bracket
Mounting
Holes

WARRANTY
Middle Atlantic Products (the "Company") warrants C5 Series Shelf System Insert to be free from defects in material or workmanship under normal use and conditions for a period of (7) years from the date of
shipment by the Company.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of and
refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after inspection
thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or any modification or alteration of the products. In addition, this warranty
does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE
OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER
PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY.
FIGURE F
8) Install dowels (4/8 places) at the desired location and slide shelf into place. Two shelves included.
(FIGURE F)
INSTALLATION CONTINUED
Page 4
FIGURE D
6) Slide the shelf system into the front of the credenza until it is flush against the mounting bracket.
7) Using the provided 10X5/8 pan head Phillips screws, affix the mounting bracket (3) places to the shelf
system from the back of the credenza. (FIGURE D)
Back of Credenza