Mitel Superset 1000 Installation instructions

Global Headquarters
Tel: [phone]
Fax: [phone]
U.S.
Tel: [phone]
Fax: [phone]
EMEA
Tel: [phone]
Fax: [phone]
CALA
Tel: [phone]
Fax: [phone]
Asia Pacic
Tel: [phone]
Fax: [phone]
For more information on our worldwide oce locations, visit our website at www.mitel.com/oces
THIS DOCUMENT IS PROVIDED TO YOU FOR INFORMATIONAL PURPOSES ONLY. The information furnished in this document, believed by Mitel to be accurate
as of the date of its publication, is subject to change without notice. Mitel assumes no responsibility for any errors or omissions in this document and shall
have no obligation to you as a result of having made this document available to you or based upon the information it contains.
M MITEL (design) is a registered trademark of Mitel Networks Corporation. All other products and services are the registered trademarks of their respective
holders.
© Copyright 2008, Mitel Networks Corporation. All Rights Reserved.
www.mitel.com
Safety Instructions:
Mitel 1000
MITEL
3000

1 Introduction
Congratulations on becoming the owner of the Mitel 1000
combined voice & data communications system. You will now
be able to access the Internet using your high-speed DSL
connection, share your phone connection between fixed &
cordless handsets and access the latest in ‘Voice over IP’
services.
This User Guide will show you how to connect Mitel 1000 and
how to customize its configuration to get the most out of your
new product.
Conformance
This equipment is designed for use in the United States and
Canada.
This equipment complies with the following standards:
FCC Part 15, Subparts B, C, D
Industry Canada RSS-213, RSS-210, CS-03
FCC Part 68
UL60950-1/CSA C22.2 No. 60950-1
Analog extension ports: TNV3
CO port: TNV3
ADSL port: TNV3
Power fail port TNV3
LAN/WAN ports SELV
Doorstrike Port SELV
Important Safety instructions
The following safety information is reprinted from IEC60950.
• When using your telephone equipment, basic safety
precautions should always be followed to reduce the risk of
fire, electric shock, and injury to persons, including the
following:
• Read and understand all instructions.
• Follow all warnings and instructions marked on the product.
• Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
• Do not use this product near water (for example, in a wet
basement).
• Do not place this product on an unstable cart, stand, or table.
The product can fall, causing serious damage to the product.
• Slots and openings in the cabinet and the back or bottom are
provided for ventilation, to protect it from overheating; these
openings must not be blocked or covered. This product
should never be placed near or over a radiator or heat
register. This product should not be placed in a built-in
installation unless proper ventilation is provided.
• This product should be operated only from the type of power
source indicated in the manual. If you are not sure of the type
of power source to your building, consult your dealer or local
Power Company.

• The mains power socket outlet must be located near the
product and must be easily accessible to allow
plugging/unplugging.
• Do not allow anything to rest on the power cord. Do not locate
this product where persons walking on it will abuse the cord.
• Do not use an extension cord with this product’s AC power
cord. The AC outlet for this product should not be used for
any other electrical equipment.
• Never push objects of any kind into this product through
cabinet slots as they can touch
dangerous voltage points or short out parts that could result in
a risk of fire or electric shock. Never spill liquid of any kind on
the product.
• To reduce the risk of electric shock, do not disassemble this
product, but take it to a qualified serviceman when some
service or repair work is required. Opening or removing
covers can expose you to dangerous voltages or other risks.
• Incorrect re-assembly can cause
electric shock when the product is subsequently used.
• Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
- When the power supply cord or plug is damaged or
frayed.
- If liquid has been spilled into the product.
- If the product has been exposed to rain or water.
- If the product does not operate normally by following the
operating instructions.
- Adjust only those controls that are covered by the
operating instructions because improper adjustment of
other controls can result in damage and will often require
extensive work by a qualified technician to restore the
product to normal operation.
- If the product has been dropped or the cabinet has been
damaged.
- If the product exhibits a distinct change in performance.
• Avoid using a telephone (other than a cordless type)
during an electrical storm. There can be a remote risk
of electric shock from lightning.
• Do not use the telephone to report a gas leak in the
vicinity of the leak.
Save These Instructions.
CAUTION
Use only 26 AWG line cord or larger for
Central Office line connections.

FCC Regulatory Information
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by ACTA.
On the exterior of the cabinet of this equipment is a label that
contains, among other information, a product identifier in the
format US:LKCMF01BSIGMA If requested, this number must
be provided to the telephone company.
• FCC Registration Number: LKCMF01BSIGMA
• Ringer Equivalence Number (REN): 0.1B
• Facility Interface Code (FIC): 02LS2
• Service Order Code (SOC): 9.0Y
• USOC Jack Type: RJ11C
A FCC compliant telephone cord and modular plug is provided
with this equipment. This equipment is designed to be
connected to the telephone network or premises wiring using a
compatible modular jack that is Part 68 compliant. See
Installation Instructions for details.
The REN is used to determine the quantity of devices that may
be connected to the telephone line. Excessive RENs on the
telephone line may result in the devices not ringing in response
to an incoming call. Typically, the sum of RENs should not
exceed five (5.0). To be certain of the number of devices that
may be connected to a line (as determined by the total RENs)
contact the local Telephone Company.
If this system causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance
notice isn't practical, the Telephone Company will notify the
customer as soon as possible. Also, you will be advised of your
right to file a complaint with the FCC if you believe it is
necessary.
The Telephone Company may make changes to it's facilities,
equipment, operations or procedures that could affect the
operation of the equipment. If this happens the Telephone
Company will provide advance notice so you can make the
necessary modifications to maintain uninterrupted service.
If the equipment is causing harm to the telephone network, the
Telephone Company may request that you disconnect the
equipment until the problem is resolved.
Connection to party line service is subject to state tariffs.
(Contact the state public utility commission, public service
commission or corporation commission for information.)
This equipment is hearing aid compatible.
Customer Owned Coin/Credit Card Phones
To comply with state tariffs, the Telephone Company must be
given notification prior to connection. In some states, the state
public utility commission, public service commission or
corporation commission must give prior approval of connection.
Data Equipment
The table below shows which jacks are associated with which
modes of operation:
Mode of Operation USOC Jack
Permissive RJ11C

Systems
Facility Interface Codes (FIC), Service Order Codes (SOC),
USOC Jack Codes and Ringer Equivalence Numbers (REN)
are shown in the table below for each port where applicable:
Automatic Dialers
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR)
MAKING TEST CALLS TO EMERGENCY NUMBERS:
1. Remain on the line and briefly explain to the dispatcher the
reason for the call.
2. Perform such activities in the off-peak hours, such as early
morning or late evenings.
Toll Restriction and Least Cost Routing Equipment
The software contained in Mitel 1000 to allow user access to the
network must be upgraded to recognize newly established
network area codes and exchange codes as they are placed
into service.
Failure to upgrade the premises systems or peripheral
equipment to recognize the new codes as they are established
will restrict the customer and the customer's employees from
gaining access to the network and to these codes.
Equipment with Direct Inward Dialing (DID)
ALLOWING THIS EQUIPMENT TO BE OPERATED IN SUCH
A MANNER AS TO NOT PROVIDE FOR PROPER ANSWER
SUPERVISION IS A VIOLATION OF PART 68 OF THE FCC'S
RULES
PROPER ANSWER SUPERVISION IS WHEN:
A. This equipment returns answer supervision to the PSTN
when DID calls are:
• Answered by the called station
• Answered by the attendant
• Routed to a recorded announcement that can be
administered by the CPE user.
• Routed to a dial prompt
B. This equipment returns answer supervision on all DID calls
forwarded to the PSTN.
Permissible exceptions are:
• A call is unanswered
• A busy tone is received
• A reorder tone is received
Equal Access Requirements
This equipment is capable of providing users access to
interstate providers of operator services through the use of
access codes. Modification of this equipment by call
aggregators to block access dialing codes is a violation of the
Telephone Operator Consumers Act of 1990.
Electrical Safety Advisory
It is strongly suggested that an AC surge arrestor be installed in
the AC outlet to which this equipment is connected.
Port FIC SOC USOC REN
Line 1 02LS2 9.0Y RJ11C 0.1B
Line 2 02LS2 9.0Y RJ11C 0.1B
ADSL 02LS2 9.0Y RJ11C 0.1B

Modifications
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment. There are no user-serviceable parts or
adjustments inside this equipment - please do not open the
equipment case.
Industry Canada Regulatory Information
This product meets the applicable Industry Canada technical
specifications/Le présent materiel est conforme aux
specifications techniques applicables d’Industrie Canada.
NOTICE: This equipment meets the applicable Industry
Canada Terminal Equipment Technical Specifications. This
is confirmed by the registration number. The abbreviation, IC,
before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating
that Industry Canada technical specifications were met. It
does not imply that Industry Canada approved the
equipment.
AVIS : Le présent matériel est conforme aux spécifications
techniques d’Industrie Canada applicables au matériel terminal.
Cette conformité est confirmée par le numéro d'enregistrement.
Le sigle IC, placé devant le numéro d'enregistrement, signifie
que l’enregistrement s’est effectué conformément à une
déclaration de conformité et indique que les spécifications
techniques d'Industrie Canada ont été respectées. Il n’implique
pas qu’Industrie Canada a approuvé le matériel.
NOTICE: The Ringer Equivalence Number (REN) for this
terminal equipment is 0.1B. The REN assigned to each terminal
equipment provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not
exceed five.
AVIS : L'indice d'équivalence de la sonnerie (IES) du présent
matériel est de 0.1B. L'IES assigné à chaque dispositif terminal
indique le nombre maximal de terminaux qui peuvent être
raccordés à une interface téléphonique. La terminaison d'une
interface peut consister en une combinaison quelconque de
dispositifs, à la seule condition que la somme d'indices
d'équivalence de la sonnerie de tous les dispositifs n'excède
pas 5.
Privacy on DECT Handsets
Privacy of communications may not be ensured when using
DECT telephones with this product.

Radio Interference
This device complies with Part 15 of the FCC Rules and RSS-
213 of Industry Canada. Operation is subject to the following
two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules and RSS-213 of Industry Canada. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
RF Radiation Exposure
This equipment complies with FCC and Industry Canada
radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated
with a minimum distance of 8 inches (20 centimeters) between
the radiator and your body.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
Basic Requirements
In order to use all the features of the Mitel 1000 system, you
must have the following:
DSL service up and running on your telephone line (or an
equivalent broadband Internet access).
Instructions from your ISP on what type of Internet access you
will be using, and the addresses needed to set up access.
Instructions from your ISP on the settings required to configure
your Voice over IP (VoIP) service.
One or more computers each containing an Ethernet card
(10Base-T/100Base-T network interface card (NIC)).
For system configuration using the supplied web-based
program: a web browser such as Internet Explorer v4 or later, or
Netscape v4 or later. Note that version 4 of each browser is the
minimum version requirement – for optimum display quality, use
Internet Explorer v5, or Netscape v6.1.

Note
You do not need to use a hub or switch in order to connect more
than one Ethernet PC to your Mitel 1000. Instead, you can
connect up to four Ethernet PCs directly to your Mitel 1000 using
the ports labeled on the rear panel.
Using this Document
Notational conventions
Acronyms are defined the first time they appear in the text and
also in the glossary.
The term LAN refers to a group of Ethernet-connected
computers at one site.
The term WLAN refers to a group of Wireless-connected
computers at one site.
Typographical conventions
Italic text is used for items you select from menus and drop-
down lists and the names of displayed web pages.
Bold text is used for text strings that you type when prompted by
the program, and to emphasize important points.
Special messages
This document uses the following icons to draw your attention to
specific instructions or explanations.
Note
Provides clarifying or non-essential information on the current
topic.
Definition Explains terms or acronyms that may be unfamiliar to many
readers. These terms are also included in the Glossary.
WARNING
Provides messages of high importance, including messages
relating to personal safety or system integrity.
LR2770.06300-1

Global Headquarters
Tel: [phone]
Fax: [phone]
U.S.
Tel: [phone]
Fax: [phone]
EMEA
Tel: [phone]
Fax: [phone]
CALA
Tel: [phone]
Fax: [phone]
Asia Pacic
Tel: [phone]
Fax: [phone]
For more information on our worldwide oce locations, visit our website at www.mitel.com/oces
THIS DOCUMENT IS PROVIDED TO YOU FOR INFORMATIONAL PURPOSES ONLY. The information furnished in this document, believed by Mitel to be accurate
as of the date of its publication, is subject to change without notice. Mitel assumes no responsibility for any errors or omissions in this document and shall
have no obligation to you as a result of having made this document available to you or based upon the information it contains.
M MITEL (design) is a registered trademark of Mitel Networks Corporation. All other products and services are the registered trademarks of their respective
holders.
© Copyright 2008, Mitel Networks Corporation. All Rights Reserved.
www.mitel.com