Mitutoyo HDS-H30C User manual

Printed in Japan
Mitutoyo Corporation 20-1, Sakado 1-Chome, Takatsu-ku, Kawasaki-shi, Kanagawa 213-8533, Japan
1. Product Capabilities
This product can work as a height measuring instrument, by touching the scriber to point (①) to
measure the height (②).
It can also scribe precisely on surfaces of workpiece (③) with the tip of a part called a scriber.
3
2
1Scriber
2. Installation Environment
Only use this product in the following environments.
• Areas with minimal dirt and dust
• Areas with minimal vibrations
• Areas with an ambient temperature between 0 °C and 40 °C
(For precision measurements, the temperature should be consistently around 20 °C.)
• Areas with low humidity
• On a surface plate
Avoid using the product in the following environments.
• In locations where it may be directly exposed to cutting fluids, water, etc.
• In locations where it may be exposed directly to sunlight or hot or cold wind
• In locations near machines that generate electromagnetic noise, such as welders or electrical
discharge machines
3. Precautions for Use
1) When using the product for the first time
Wipe the rust preventive oil from the product with a soft cloth soaked with cleaning oil, etc., and
then install the supplied battery.
2) Cleaning before use
Clean the following parts, and then use the product only after confirming that it is free of dirt or
burrs (projections caused by damage, etc.).
• Surface plate
• Beam, lower base surface, scriber mounting surface, and scriber measurement surface
3) When carrying or moving
■Correct holding
• First lock the slider securely in place, and be sure to hold the bottom
of the base while lightly supporting the rear surface of the slider.
• When measuring or moving on a surface plate, grip the base
and slide it to move.
■Incorrect holding
Do not touch the top part of the beam, as doing so could
affect accuracy.
4) Other
• Never apply an external voltage to this product, such as entering numbers using an electric
marking pen. This may cause failure.
• Do not subject the product to excessive force or impact through dropping or the like. This may
cause failure, such as malfunctions due to rack damage.
4. Confirmation of Accessories
SR44 1.55V
• Scriber • Scriber clamp • Battery (SR44)
• User's Manual and warranty
Safety Precautions
To ensure operator safety, use this product in conformance with the directions, functions
and specifications given in this User's Manual.
Use under other conditions may compromise safety.
• Always keep batteries out of reach of children, and if swallowed, consult a physician immediately.
• Batteries should never be short-circuited, disassembled, deformed or come in contact with
extreme heat or flames.
• If battery alkaline liquid comes in contact with the eyes, flush eyes immediately with clean
water and consult a physician. If battery alkaline liquid comes in contact with the skin,
flush the exposed area thoroughly with clean water.
• Never attempt to charge the primary battery or reverse the positive-negative terminals when
mounting.
Improper battery handling or mounting may cause the battery to explode, cause
battery leakage and/ or serious bodily injury or malfunctioning.
• The tip of the scriber on this product is sharp. Always handle with care to avoid injury.
If the product is to be out of use for three months or more, remove the battery before storage.
Liquid leakage from the battery may damage the product.
Tips
• Be sure to use an SR44 battery (silver oxide battery).
• Never disassemble this product, unless removing the battery cover to replace the battery.
If the product is disassembled, the warranty will no longer apply.
• Be sure that you thoroughly understand the content in both "2. Installation Environment"
and "3. Precautions for Use" before using this product.
ABS Digimatic Height Gage
User's Manual No. 99MAF026A1
Date of publication: June 1, 2019
Contents
1. Product Capabilities ............................................................................................... Page 1
2. Installation Environment ......................................................................................... Page 1
3. Precautions for Use................................................................................................ Page 1
4. Confirmation of Accessories................................................................................... Page 1
5. Names and Functions of Components ................................................................... Page 2
6. Preparations before Use ........................................................................................ Page 2
7. Moving the Slider Vertically .................................................................................... Page 3
8. Using as a Scribing Tool......................................................................................... Page 3
9. Using as a Measuring Instrument........................................................................... Page 3
10. Usage Scenarios .................................................................................................... Page 4
11. Routine Maintenance ............................................................................................. Page 4
12. Troubleshooting...................................................................................................... Page 4
13. Specifications ......................................................................................................... Page 4
14. Options (Sold Separately) ...................................................................................... Page 5
HDS-H30C / HDS-H60C / HDS-H12"C / HDS-H18"C / HDS-H24"C
en

Printed in Japan
Mitutoyo Corporation 20-1, Sakado 1-Chome, Takatsu-ku, Kawasaki-shi, Kanagawa 213-8533, Japan
5. Names and Functions of Components
1) Main body
11
12
13
10
7
6
3
1
2
8
9
4
5
①Beam
Supports the slider.
②Main scale
③Feed handle
Turning it left/right coarsely moves the slider vertically.
④Clamp lever
Locks/unlocks the slider movement.
⑤Output connector
This connector is used to connect an optional external device (sold separately).
⑥Label
Indicates product information such as code No.
⑦Base
It grips when measuring or moving the main body on a surface plate.
⑧Scriber
A tool used to make scribe lines. It can also be used to measure heights by touching it to
the point to be measured.
⑨Scriber clamp
Fixes the inserted scriber to the main body with the clamp screw.
⑩Clamp screw
The screw which fixes the scriber.
⑪Battery cover
Covers the battery insertion part.
⑫LCD display
The display is used to show measured values and messages.
⑬Slider
The moving part on the main body in which the LCD display and controls are located.
2) Controls
1
2
3
5
4
①[ON/OFF] switch
Used to turn the power on/off.
②[ORIGIN] switch
Used to set the reference for absolute measurement (ABS).
③[ZERO/ABS] switch
Used to switch between absolute measurement (ABS) and incremental measurement
(INC).
④[in/mm] switch (inch display models only)
Used to switch units (in/mm).
⑤[HOLD/DATA] switch
Used to hold the measured value display or to output measurement results to an optional
external device (sold separately).
3) LCD display
1 2
3
4
①Lights up when the reference is switched to incremental measurement (INC).
②Lights up when the battery is depleted.
③Displays the measured value and unit.
④Lights up when the measured value is being held in the display.
6. Preparations before Use
1) Mounting the scriber
1 Insert the scriber clamp all the way to the end of the jaw.
2 Insert the scriber into the scriber clamp.
3 Tighten the clamp screw.
1
2
3
Tips
Mount the scriber as close to the beam as possible, so that it protrudes no more than
necessary. Too much protrusion will cause measurement errors (with error effect increased 1.5
times if the protrusion of the scriber tip from the beam changes from 100 mm to 150 mm). If the
scriber must be used protruding longer, be careful to apply only the necessary measuring force.
2) Installing (replacing) the battery
1 Turn the power off, and then slide the battery cover in the direction of the arrow to remove it
from the controls.
2 Insert the new battery (SR44 part No. 938882) with the plus side facing upward.
3 Slide the battery cover back into place.
4 Slowly bring the scriber into contact with the surface plate.
5 Press the [ORIGIN] switch for at least 1 second.
》 The value [0.00] lights up (the reference for ABS has been set).
1
3
5
2
SR44
+ terminal
When inserting the battery, be careful not to crush the + terminal.
Tips
• Always set the reference for ABS after inserting a battery. If not set, it may result in an error
display (E displayed for minimum digit) or prevent accurate measurement. When setting the
reference, refer to "1) Reference setting".
• When replacing the battery, wait at least 10 seconds before inserting the new battery.
• If the display or functionality is abnormal after replacing the battery, reinstall the battery.
• Press the [ON/OFF] switch to turn the power off. Always turn the power off when you are
finished using the product.

Printed in Japan
Mitutoyo Corporation 20-1, Sakado 1-Chome, Takatsu-ku, Kawasaki-shi, Kanagawa 213-8533, Japan
7. Moving the Slider Vertically
Loosen the clamp lever so that the slider can be moved.
When moving the slider vertically, hold the base surface down with the palm of one hand as you
turn the feed handle right or left with the other hand.
Moving the slider will move the scriber up and down.
Move the slider slowly when bringing the scriber into contact with the surface plate or workpiece.
Scriber Slider
Tips
• If the slider is moved further (measuring force is applied) after the scriber makes contact with
the workpiece, the bottom of the base will lift from the surface plate, causing measurement
errors. In order to obtain accurate measurements, bring the scriber into contact with the
workpiece as slowly as possible and apply constant force lightly. Before measuring, confirm
that the bottom of the base is free of dirt and burrs (burrs caused by damage, etc.).
• When bringing the scriber into contact with the workpiece, you can confirm the scriber contact
state and close contact of base and surface plate by sliding the base slightly over the surface
plate once the slider has stopped moving.
• In order to make accurate measurements, bring the scriber into contact with the workpiece
several times and confirm that the LCD shows a stable value when the scriber makes contact
with the workpiece.
8. Using as a Scribing Tool
When scribing, make sure that the scriber moves in a consistent direction. Make sure that the
clamp lever is firmly tightened and that the slider is fixed.
Tips
When setting the reference, refer to "1) Reference setting".
9. Using as a Measuring Instrument
1) Reference setting
Set the reference when measuring height. The distance from the reference set will be displayed
as a measured value of height. This product supports both absolute measurement (ABS) and
incremental measurement (INC) reference setting. Be sure to set the reference for ABS (and for
INC as needed) prior to use.
■ Reference (zero) setting for absolute measurement (ABS)
This method is used to set the reference for absolute measurement. Normally, the workpiece
height is measured with the surface plate surface as the reference. The set reference is fixed
until the battery is discharged, so this is a convenient way to measure multiple measurement
points with the surface plate surface as the reference.
Example: Setting surface plate surface as the reference with a value of 0 mm
Measure the height with
the surface plate surface
as the reference
Surface plate surface
As an example, this section describes how to set the surface plate surface as the reference.
Tips
The set reference is stored until the battery is replaced. If the battery is replaced, the reference
will need to be set again.
1 Confirm that the power is on.
2 Slowly bring the scriber into contact with the surface plate.
3 Press the [ORIGIN] switch for at least 1 second.
》 [0.00] is displayed (the reference for ABS has been set).
■Reference (zero) setting for incremental measurement (INC)
This method is used to set an arbitrary point on the workpiece as the reference. The specified
point will be used as the reference for measurement (value of 0 mm). As the reference is reset
each time the switch is pressed, this is a convenient way to measure multiple measurement
points while resetting the reference.
a1
Example: Setting surface a1 as the reference (value is always 0 mm)
Measure the height with the
a1 surface as the reference
1 Confirm that the power is on.
2 Slowly bring the scriber into contact with an arbitrary point on the workpiece.
3 Press the [ZERO/ABS] switch.
》[INC] lights up and [0.00] is displayed (the reference for
INC has been set).
2) Switching measurement modes
1 Briefly press the [ZERO/ABS] switch.
》[INC] lights up and the value [0.00] is set.
2 Press and hold the [ZERO/ABS] switch for at least 2 seconds.
》[INC] goes out, and the slider position compared to the
reference set with ABS will be displayed.
3) Measurement
<Example> Measuring dimensions A and B of the workpiece
shown in the figure at right
1 Set the surface plate surface as the reference for ABS.
Tips
Refer to "■ Reference (zero) setting for absolute measurement
(ABS)
" for information on setting.
2
Slowly bring the scriber into contact with the upper surface A.
》Dimension A is measured.
3 Set the lower surface B as the reference for INC.
Tips
Refer to "■ Reference (zero) setting for incremental measurement
(INC)
" for information on setting.
4
Slowly bring the scriber into contact with the upper surface B.
》Dimension B is measured.
21
A 130
B 20
2
4
3

Printed in Japan
Mitutoyo Corporation 20-1, Sakado 1-Chome, Takatsu-ku, Kawasaki-shi, Kanagawa 213-8533, Japan
10. Usage Scenarios
1) Holding the displayed measurement result
The displayed measurement result can be held even if the slider is moved.
1 Press the [HOLD/DATA] switch.
》[H] lights up (displayed measurement result is held).
2 Press the [HOLD/DATA] switch again.
》 [H] goes out (displayed measurement result is released).
Tips
If an external device is connected to the output connector on the product, the [HOLD/DATA]
switch will instead be used as a switch for outputting measured value.
2) Outputting measurement results to an external device
Measured values can be output to an optional external device (sold separately) connected to the
product.
1 Connect the external device to the output connector on the product.
2 Press the [HOLD/DATA] switch.
Tips
Measured values can also be output by operating the external device. Refer to the User's
Manual included with the external device for details.
11. Routine Maintenance
1) Cleaning
• After use, clean the entire product and check that none of the parts are damaged.
• Use a lint-free cloth or paper soaked in alcohol to wipe the main body (beam, base,
scriber, etc.). Do not use thinner or other organic solvents. Use an old toothbrush or the like to
clean the rack part on the rear surface of the beam.
2) Storage
• When storing the product, leave the scriber hanging about 1 mm from the surface plate
surface, and do not tighten the clamp lever.
• Store so that the tip of the scriber does not protrude from the surface plate.
• Always turn the power off before storing.
• Do not store the product in a place with a high temperature or humidity, or a lot of dust or
oil mist.
• If the product is to be out of use for three months or more, remove the battery.
• Apply anti-rust treatment after use. Rust may cause malfunction.
• We recommend periodically testing and calibrating the product for accuracy.
• If any abnormalities occur, contact the dealer where the product was purchased.
12. Troubleshooting
If a problem occurs while using this product, please try one of the solutions provided below. If the
solution does not work, contact our service department via your dealer for repair.
1) If the following problem occurs
Problem Cause Solution
• The displayed values
flicker or disappear
temporarily.
• An accurate
measurement result
cannot be obtained.
• The power is turned
off automatically.
The product is used
in environments where
electromagnetic interference
exceeds requirements
defined in the EMC Directive.
• The product will return to normal after
removing the electromagnetic
interference caused by electrostatic
discharge.
•
If this problem is due to electromagnetic
interference acting on the AC or DC
power line, check the circumference of
the power line, and then make a
measurement again.
• If a brownout occurs, the product will
return to normal after the recovery
from the low voltage.
The display flickers. The main scale surface is
dirty.
Clean the main scale surface, and then
apply a small amount of low-viscosity
oil to repel water.
2) If a warning is displayed
Warning Cause Solution
Err C The main scale surface is
dirty.
Clean the main scale surface, and then apply a
small amount of low-viscosity oil to repel water.
E (displayed
for minimum
digit)
• The reference for absolute
measurement (ABS) is not
set after inserting the
battery.
• The main scale surface
is dirty.
• Set the reference for absolute measurement (ABS).
• Clean the main scale surface, and then apply a
small amount of low-viscosity oil to repel water.
Battery is depleted. Replace with a new battery.
13. Specifications
1) Product specifications
●Metric display models (HDS-H30C/HDS-H60C)
Model number HDS-H30C HDS-H60C
Code No. 570-302 570-304
Maximum measurement
length
300 mm 600 mm
Maximum permissible
error (
E
MPE)±0.03 mm ±0.05 mm
Resolution 0.01 mm
Maximum response speed Unlimited
Power SR44 (silver oxide battery) x 1 (part No.938882)
Battery life Approx. 20,000 hours
Operating temperature 0 °C to 40 °C
Storage temperature -10 °C to 60 °C
Scriber Part No.07GZA000
Scriber clamp Part No.05GZA033
●Inch display models (HDS-H12"C/HDS-H18"C/HDS-H24"C)
Code No. 570-312 570-313 570-314
Model number HDS-H12"C HDS-H18"C HDS-H24"C
Maximum measurement
length
12"/300 mm 18"/450 mm 24"/600 mm
Maximum permissible
error (
E
MPE)
±0.0015"/±0.03
mm ±0.0020"/±0.05 mm
Resolution 0.0005"/0.01 mm
Maximum response speed Unlimited
Power SR44 (silver oxide battery) x 1 (part No. 938882)
Battery life Approx. 20,000 hours
Operating temperature 0 °C to 40 °C
Storage temperature -10 °C to 60 °C
Scriber Part No. 900258
Scriber clamp Part No. 901385

Printed in Japan
Mitutoyo Corporation 20-1, Sakado 1-Chome, Takatsu-ku, Kawasaki-shi, Kanagawa 213-8533, Japan
2) Output specifications
• Data format
(1) Output order (2) All "F" (3) Sign (4) Measured value (5) Decimal point (6) Units
（1111）
MSD LSD
＋：0（0000）
－：8（0001）
x.x.x.x.x.x.
0（0000）mm
1（1000）inch
2（0100
）
4（0010
）
d1 d2 d3 d4 d5 d6 d7 d8 d9 d10 d11 d12 d13
(1) Output order
(2) All "F"
(3) Sign (4) Measured value
(6) Units
(5) Decimal point
• Connector layout
4
5
1
3
2
Pin No. Code
1 GND
2DATA
3 CLOCK
4 READY
5 REQUEST
• Timing chart
*1
T5 T1
[ HOLD / DATA ] *2
20 ≦T1 ≦100 ms
110 ≦T2 ≦ 140 μs（TYP：122 μs
）
110 ≦T3 ≦ 140 μs（TYP：122 μs
）
230 ≦T4 ≦ 260 μs（TYP：244 μs）
RD
REQ
DATA
CLOCK
T2 T3 T4
*1: The time until the [HOLD/DATA] switch goes to the Low level and REQUEST is input.
T5 is determined by the performance of the data processing device.
*2: Enabled only when the [HOLD/DATA] switch is used.
14. Options (Sold Separately)
●Digimatic connection cable (for IT-016U/IT-007R/DP-1VA LOGGER/MUX-10F/etc.)
1 m: Part No. 905338
2 m: Part No. 905409
●USB input tool direct
USB-ITN-F (2 m): Part No. 06AFM380F
●U-WAVE-T dedicated connection cable
Standard (160 mm): Part No. 02AZD790F
Foot switch: Part No. 02AZE140F
●Holder arm
Part No. 953638 (for metric display models), 953639 (for inch display models)
●Clamp
Part No. 902053 (ø6/ø8 with dovetail for metric display models), 900322 (ø4/ø9.52 with
dovetail for inch display models)
* The holder arm and clamp can be used to attach a test indicator (sold separately).