Mocka Brooklyn Change Table User manual

Phillips & Flathead screwdrivers and hammer required
Brooklyn Change Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
1
X
Z
Y
W
safety
strap
x1
screw
x1
long
screw
x1
wall
anchor
x1
washer
x1
mocka.co.nz | mocka.com.au
B
ACDE
F G H
12 mm
30 mm
12 mm
Hardware Supplied
*We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use.
WARNING: Any furniture that is not anchored to a wall has the potential
to tip over in certain circumstances, i.e. if a child attempts to climb up on
the furniture or in the event of an earthquake. Accordingly, we
recommend that all furniture is anchored to a wall. We supply a free
safety wall anchor with all furniture sold and we recommend these are
used to prevent your product tipping. The fixing device provided should
fit most wall types, but please note that different wall materials
may require different fixing devices from those supplied.
WARNING: Never leave a child unattended on the change table.
bolt
x28
locking
nut x28
dowel
x40
small
screw x20
I
cover
x 4
L + R
slide rail
x4
L + R
slide rail
x4
long
screw x 8
screw
x22

2
12
Brooklyn Change Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
mocka.co.nz | mocka.com.au
3
1
2
A
A
A
x4
x4
B
A
x4
B
B
A
A
A
AB
B3
A
A
7
Tighten with a screwdriver.
Attach 4 x bolt (A) to panel [1] and [2].Insert 4 x locking nut (B) into panels [3] . Insert 4 x bolt (A) into panels [3] and [7] . Tighten with a screwdriver.

3
34
Brooklyn Change Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
mocka.co.nz | mocka.com.au
6
7
B
x4
B
B
BB
C
C
Insert 4 x locking nut (B) into panels [6] . Attach 4 x dowel (C) to panel [3] and
[7].
3
I
I
I
I
A
A
A
A
E
E
A
A
E
EG
G
A
A
E
G
G
E
E
A
A
A
A
4
5
x8
E
Cover locking nuts (B) with 4 x covers (I).
Attach 2 x left slide rail (G) to panel [4] and secure with 6 x small screw (E).
Tighten with a screwdriver.
Attach 2 x right slide rail (G) to panel [5] and secure with 6 x small screw (E).
Insert 12 x bolt (A) into panel [4] and [5].
E
E
E
E
1
2I

4
56
Brooklyn Change Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
mocka.co.nz | mocka.com.au
5
8
8
7
3
B
C
C
C
C
C
C
C
C
BB
B
B
B
x6
B
Insert 6 x dowel (C) into panel [3] and [7] and [8] . Attach panel [3] to panels [7]
and [8] and secure with 6 x locking nuts (B). Tighten with a screwdriver.
5
4
8
8
7
3
C
C
C
C
C
B
BB
B
B
B
x6
B
Insert 6 x dowel (C) into panel [3] and [7] and [8] . Attach panel [3] to panels [7]
and [8] and secure with 6 x locking nuts (B). Tighten with a screwdriver.

5
78
Brooklyn Change Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
mocka.co.nz | mocka.com.au
On the back side of the set, fit boards [10] and [11] into the grooves. Use
small 20x screws (D) all around to fasten boards to the change table unit.
10
11
D
D
D
D
D
D
DD
D
DD
D
D
D
D
DD
D
D
D
Drawers (x2)
To assemble the drawers, first screw 4x bolts (A) into front panel [15].
Fit panels [12] and [13] over the bolts as shown, ensuring the grooves
in panels face inwards. Secure using 4x locking nuts (B) and tighten
with a screwdriver.
13
12
15
BB
B
AA
AA
A
x4
B
x4

6
910
Brooklyn Change Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
mocka.co.nz | mocka.com.au
Drawers (x2)
16
9
9
C x2
C x2
Slot panel [16] down into grooves in the side and front panels. Insert 2x
dowels (C) into the end of both support braces [9] and peg into holes in
front panel [15].
Drawers (x2)
F
14
F
F
F
Cx2
Cx2
x4
F
Insert 2x dowels (C) into the other end of each support piece [17]. Place
back panel [14] into position on dowels and fasten into place using 4x
screws (F).

7
11 12
Brooklyn Change Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
mocka.co.nz | mocka.com.au
Drawers (x2)
E
H
E
E
Finally, attach rail hardware (H) to both left and right side of the drawer
using screws (E). Repeat Steps 7 to 10 until all four drawers are fully
assembled.
Now both drawers are made up, slide them into rails in the change
table unit.
x2

8
13 14
Brooklyn Change Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
mocka.co.nz | mocka.com.au
Attach the safety strap (W) to the top of the back side of the unit using
screw (Y). Tighten with a screwdriver.
Once assembled lift furniture into place, do not drag. Use a drill to create
a small hole lining up with the top of the safety strap (W). Fasten to wall
using wall anchor (X), washer (Z) and screw. Ensure the unit is balaced
and steady before use. You’re done, enjoy!
YY
W
W
x1
X
Z
x1
wall
screw
wall
anchor
wall
screw
Washer
Strap
Attach the safety strap (W) to the top of the back side of the unit using.