Motorola PMTN4024 User manual

Single-Unit
Charger
Accessories
Professional Radio
cover(2).fm Page 1 Monday, June 11, 2007 5:37 PM

blank.fm Page 1 Monday, June 11, 2007 5:40 PM

1
IMPORTANT
SAFETY INSTRUCTIONS
This document contains important safety and operating
instructions. Please read these instructions carefully and
save them for future reference.
Before using the battery charger, read all the instructions and
cautionary markings on (1) the charger, (2) the battery, and (3) on
the radio using the battery.
WARNING
1. To reduce risk of injury, charge only the
rechargeable Motorola authorized
batteries listed in Table 1. Other batteries
may explode, causing personal injury
and damage.
2. Use of accessories not recommended by Motorola may result in
risk of fire, electric shock, or injury.
3. To reduce risk of damage to the electric plug and cord, pull by
the plug rather than the cord when disconnecting the charger.
4. An extension cord should not be used unless absolutely nec-
essary. Use of an improper extension cord could result in risk
of fire and electric shock. If an extension cord must be used,
make sure that the cord size is 18AWG for lengths up to 100
feet (30.48 m), and 16AWG for lengths up to 150 feet
(45.72 m).
5. To reduce risk of fire, electric shock, or injury, do not operate
the charger if it has been broken or damaged in any way.
Take it to a qualified Motorola service representative.
6. Do not disassemble the charger; it is not repairable and
replacement parts are not available. Disassembly of the
charger may result in risk of electrical shock or fire.
7. To reduce risk of electric shock, unplug the charger from the
ac outlet before attempting any maintenance or cleaning.
!!
Text.fm Page 1 Monday, March 17, 2008 4:28 PM

2
OPERATIONAL SAFETY GUIDELINES
• Turn radio off when charging battery.
• This equipment is not suitable for outdoor use. Use only in dry
locations/conditions.
• Connect equipment only to an appropriately fused and wired
supply of the correct voltage (as specified on the product).
• Disconnect from line voltage by removing mains plug.
• The socket outlet to which this equipment is connected should
be close by and easily accessible.
• In equipment using fuses, replacements must comply with the
type and rating specified in the equipment instructions.
• Maximum ambient temperature around the power supply
equipment must not exceed 40°C (104°F).
• Output power from the power supply unit must not exceed the
ratings stated on the product label located on the bottom of the
charger.
• Make sure the cord is located where it will not be stepped on,
tripped over, or subjected to water, damage, or stress.
MOTOROLA AUTHORIZED BATTERIES
The batteries listed in Table 1 are approved for use with the
chargers listed in Table 2.
Table 1 Motorola Authorized Batteries
Kit (part)
Number Battery Chemistry/Description
HNN9008 NiMH/High-Capacity
HNN9009 NiMH/Ultra-High-Capacity
HNN9010 NiMH/Ultra-High-Capacity, Factory Mutual
HNN9011 NiCd/High-Capacity, Factory Mutual
HNN9012 NiCd/High-Capacity
HNN9013 Lithium Ion
JMNN4023 AA Lithium Ion
Text.fm Page 2 Monday, March 17, 2008 4:28 PM

3
POWER SOURCES AND MOTOROLA AUTHORIZED
TRANSFORMERS
These Class 2 battery chargers should be used with the direct
plug-in, Motorola authorized transformers listed below:
JMNN4024 AFAT Lithium Ion
JMNN4025 NiMH Factory Mutual Intrinsically Safe
NNTN5510 GP Series ATEX Li-Ion 1480mAh
PMNN4073 Lithium Ion, Factory Mutual, IP67
PMNN4074 Lithium Ion, Non-Factory Mutual, IP67
Table 2 Power Sources/Power Supplies
Charger Kit
Number Charger Base Power Source
Power Supply
Part Number
PMTN4024 HTN9000 120Vac (U.S. Plug) 2504548T05
2571586S13
PMTN4025 HTN9000 230Vac (EURO
Plug) 2504548T07
2571586S07
PMTN4026 HTN9000 230Vac (UK Plug) 2504548T06
2571586S06
HTN2006 HTN9000 230Vac (Aust.
Plug) 2504548T08 2571586S08
PMLN5195 HTN9000 90-264Vac (UK
Plug) 2571886T01
PMLN5196 HTN9000 90-264Vac (EURO
Plug) 2571886T01
PMLN5197 HTN9000 90-264Vac (U.S.
Plug) 2571886T01
PMLN5205 HTN9000 90-264Vac(Aus/Nz
Plug) 2571886T01
Table 1 Motorola Authorized Batteries
Kit (part)
Number Battery Chemistry/Description
Text.fm Page 3 Monday, March 17, 2008 4:28 PM

4
OPERATING INSTRUCTIONS
Single-unit chargers will charge only the Motorola authorized
batteries listed in Table 1. Other batteries may not charge.
The battery charger’s pocket will accommodate either a radio with
a battery attached or a battery alone. Prior to charging a battery
with radio, turn the radio off. To charge a battery, use the
following procedure: (Refer to Figure 1, page 5)
1. Plug the round end of the transformer cord into the socket on
the back of the charger.
2. Plug the transformer into the appropriate ac outlet. The
charger LED will blink green once to indicate a successful
power-up.
3. Insert a battery, or a radio with battery (radio turned off), into
the charger's pocket by:
a. aligning the groove on each side of the battery with the
corresponding raised rail on each side of the charger
pocket
b. pressing the battery toward the rear of the pocket
c. sliding the battery into the charger pocket, ensuring
complete contact between the charger and battery
contacts
2. When the battery is properly seated in the pocket, the charger
LED will light red to indicate that the battery is charging rapidly.
When the battery is 90% charged, the LED will begin to blink
green to indicate that the battery is trickle charging. When the
battery is fully charged, the LED will change to a steady green
light to indicate that the battery is fully charged.
Note: Even though new batteries might prematurely indicate a full
charge (steady green LED), charge the battery for 14 to 16
hours prior to initial use for best performance.
Batteries will charge best at room temperature.
Text.fm Page 4 Monday, March 17, 2008 4:28 PM

5
TROUBLESHOOTING
When troubleshooting, always observe the color of the LED:
Table 3 LED Indications of Battery/Charger Status
LED Color Battery/Charger Status
No LED indication Battery is inserted incorrectly.
Single green blink Successful charger power-up
Blinking red Battery is unchargeable or not making
proper contact.
Steady red Battery is in rapid-charge mode.
Blinking yellow Battery is in charger, not in rapid-charge
mode but waiting to be charged.
Blinking green Battery is charged (to 90% or greater
capacity).
Steady green Battery is fully charged.
Figure 1 Battery Charger
SOCKET
(located here) RAISED RAIL
CHARGING
CONTACTS
POCKET
LED
WARNING
LABEL
Text.fm Page 5 Monday, March 17, 2008 4:28 PM

6
No LED Indication?
1. Check that the radio with battery, or the battery alone, is
inserted correctly (refer to step 3 on page 4).
2. Make sure that the transformer is plugged into an appropriate
ac outlet, and that the transformer cable is plugged securely
into the charger socket.
Blinking Red LED Indicator?
1. Remove the battery from the charger, and:
a. make sure that it is a Motorola authorized battery listed in
Table 1. Other batteries may not charge.
b. remove power from the battery charger and, using a clean
dry cloth, clean the gold metal, charging contacts of the
battery and charger.
2. Power up the charger and place the battery back into the charger
pocket. If the LED indicator continues to blink red, replace the
battery.
Blinking Yellow LED Indicator?
1. The battery temperature may be below 5°C (41°F) or above
40°C (104°F).
2. The voltage may be lower than the predetermined threshold
level for rapid charging.
Note: Rapid charging outside of the stated temperature and
voltage limits can drastically reduce the life expectancy of
the battery.
Note: When the battery charger detects the proper battery
conditions, rapid charging begins automatically (steady red
LED).
SERVICE
The Single-Unit Chargers are not repairable. Order replacement
chargers as necessary.
Text.fm Page 6 Monday, March 17, 2008 4:28 PM

blank.fm Page 1 Monday, June 11, 2007 5:40 PM

m
© 2007, 2008 by Motorola, Inc.
band Motorola are registered trademarks of Motorola, Inc.
All Rights Reserved.
*6804110J80*
6804110J80-E
backcover.fm Page 1 Monday, March 17, 2008 4:43 PM