Motorola PMLN6621 User manual

Multi-Unit Charger
User Instruction Sheet
PMLN6621
en zh-TW zh-CN
Untitled1.fm Page 1 Friday, January 3, 2014 9:41 AM

UIS_backcover.fm Page 1 Monday, October 14, 2013 3:42 PM

1
English
IMPORTANT
SAFETY INSTRUCTIONS
This document contains important safety and operating instructions.
Please read these instructions carefully and save them for future
reference.
Before using the battery charger, read all the instructions and cautionary
markings on (1) the charger, (2) the battery and (3) on the radio using the
battery.
Refer and follow the safety instructions and
operational safety guidelines as specified in your
Multi-Unit Charger electronic user guide and
Product Safety Booklet for Battery Chargers.
W A R N I N G
To reduce risk of injury, fire, damage or electric shock:
1. Charge only the rechargeable Motorola authorized batteries
listed in the charger user manual. Use of accessories not
recommended by Motorola may result in risk of fire, electric shock
or injury.
2. Always pull by the plug (not the cable) when disconnecting the
charger from the supply.
3. An extension cord should not be used unless absolutely
necessary. Use of an improper extension cord could result in risk
of fire and electric shock.
4. Do not operate the charger if it has been broken or damaged in
any way. Take it to a qualified Motorola service representative.
Some units are non-repairable and should be disposed in a safe
manner. Any violation of this policy can void the warranty.
5. Unplug the charger from the AC outlet before attempting any
mainenance or cleaning.
MN000218A01_a.book Page 1 Wednesday, March 19, 2014 4:18 PM

2
English
Operational Safety Guidelines
• Ensure all ventilation surfaces have unrestricted air movement.
• Turn the radio off when charging the battery, unless the manual states
otherwise.
• This equipment is not suitable for outdoor use. Use in dry locations/
conditions.
• Connect equipment only to an appropriately fused and wired supply of
the correct voltage (as specified on the product). Replacement fuses
must comply with the types and ratings specified in the equipment
instructions.
• Disconnect from line voltage by removing plug.
• The plug should be easily accessible and removeable from the supply.
• Maximum ambient temperature around the charger must not exceed
40 °C (104 °F).
• Output power from the power supply unit must not exceed the ratings
stated on the product label located on the bottom of the charger.
• Ensure cables are located where they will not be stepped on, tripped
over, or subjected to water, damage or stress.
• Ensure that the unit and cables are checked regularly for damage.
This User Instruction Sheet is applicable for the Multi-Unit Chargers listed in
Table 1
Table 1: Charger Kit Number
Plug Type Charger Kit Power Cord
Taiwan PMLN6613 3004209T04
China PMLN6622 3004209T14
Hong Kong PMLN6618 3004209T02
Australia / New Zealand PMLN6619 3004209T07
Korea PMLN6615 3004209T13
Japan PMLN6620 3004209T15
MN000218A01_a.book Page 2 Wednesday, March 19, 2014 4:18 PM

3
English
DESCRIPTION
The Multi-Unit Charger comprises a base unit which accommodates six
charging locations. Each charging location is fitted with a charging pocket.
The kit contains:
• 1 Multi-Unit Charger base unit
• 6 Charging Pockets
• 1 regional line cord
Figure 1: Multi-Unit Charger
OPERATING INSTRUCTIONS
1. The Multi-Unit Charger equipped with charging pocket is designed for
use with Motorola authorized batteries listed in the User Manual only.
Other batteries may not charge.
2. The Multi-Unit Charger can charge up to 6 radios or batteries listed in
the User Manual.
3. Prior to operating the charger, check that all radio and battery inserts
are in place and properly latched.
4. Prior to charging a battery with radio, turn the radio off.
5. Plug the charger end of the power supply cord into the power
receptacle located at the back of the charger.
6. Plug the wall receptacle end of the power supply cord into the
appropriate AC outlet.
7. Insert a battery, or a radio with the battery (radio turned off), into the
charger’s pocket.
MN000218A01_a.book Page 3 Wednesday, March 19, 2014 4:18 PM

4
English
Table 2: Battery Charging Indicators
Charger
Indicator Description
No indication Battery is inserted incorrectly.
Single green
blink Successful charger power-up.
Blinking red Battery is unable to charge or not making proper contact.
Steady red Battery is in rapid-charge mode.
Blinking Orange
Battery is recognized by charger but is waiting to rapid charge.
(Either the battery voltage is too low due to over-discharge or, the
battery temperature is too low or too high to allow rapid charging.
When this condition is corrected, the battery will automatically
begin rapid charging).
Additional case for new ultra-high-capacity IMPRES™ Lithium-
ion (Li-ion) batteries. The new ultra-high-capacity Li-ion batteries
have capacities exceeding 2000 mAHr. After approximately 15
minutes, the LED may go into a Flashing Red mode. Remove
and reinsert to get another over-discharge recovery period. This
procedure may need to be repeated several times.
Blinking green Battery charging is tapering down (typically when the battery is
charged approximately 90% or greater).
Steady green Battery is nearly charged or fully charged.
MN000218A01_a.book Page 4 Wednesday, March 19, 2014 4:18 PM

5
English
Figure 2: Multi-Unit Charger
CHARGING POCKET INSTALLATION
Removing Charging Pocket from Multi-Unit Charger
1. Remove the screw that secures the Charging Pocket to the base.
2. Lift the Charging Pocket a few inches away from the base.
3. Remove the Pocket Harness by pulling straight up on the connector
(refer to Figure 4).
Securing Charging Pocket to Multi-Unit Charger
1. Connect Pocket Harness by plugging in the connector to the
receptacle on Multi-Unit Charger (refer to Figure 4).
2. Slot in the Charging Pocket to the base and ensure the Charging
Pocket is flushed in to the Multi-Unit Charger. Affix the Charging
Pocket screw.
To reduce risk of electric shock, unplug the charger
from the AC outlet before removing or replacing
Charging Pocket.
Charging
contacts
Power Receptacle
(located here)
Charging
Pocket
Charging
Indicator
W A R N I N G
MN000218A01_a.book Page 5 Wednesday, March 19, 2014 4:18 PM

6
English
Figure 3: Removing Charging Pocket
Charging
Pocket
Screw
MN000218A01_a.book Page 6 Wednesday, March 19, 2014 4:18 PM

7
English
Figure 4: Connecting Pocket Harness
For more information on this Multi-Unit Charger, please refer to the charger
electronic user manual (Motorola Publication part number: MN000217A01)
which can be found at www.motorolasolutions.com/userguides.
Receptacle (on Multi-
Unit Charger)
Connector
(on Charging
Pocket)
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo
are trademarks or registered trademarks of Motorola Trademark Holdings,
LLC and are used under license. All other trademarks are the property of
their respective owners.
© 2014 Motorola Solutions, Inc. All rights reserved.
MN000218A01_a.book Page 7 Wednesday, March 19, 2014 4:18 PM

8
English
Notes
MN000218A01_a.book Page 8 Wednesday, March 19, 2014 4:18 PM