MULTISPAN DIN-63 User manual

OPERATING MANUAL
MULTIRANGE TIMER
DIN-63
Technical Specification
LED
Connection Diagram
3 Digit Seven Segment LED Display
Up & Down Selectable
Power Supply
Operating
Temperature
Relative
Humidity
100 to 270V AC, 50/60Hz
Up to 95% RH Non Condensing
Model
Display
Dirction
Size (mm)
Range
Output
76 (H) x 27 (W) x 85 (D) mm
0 to 999 Second/Minute/Hours and
Decimal Point Selectable
1 Relay with 2C/O (5 Amps/230V AC)o/p
DIN-63
0° To 55°
C C
Display
All Led are in Red color.
RLY : Shows the relay status.
M : Shows that the set time is in minutes.
H : Shows that the set time is in hours.
S : Shows that the set time is in seconds.
DIN-63
www.multispanindia.comPage-2
Made in India
ON OFF
SWITCH 1,SWITCH 2 & SWITCH 3
for DP & UNIT Selection.
SWITCH 4 For
Mode selection
ON Delayed OFF
Delayed ON
OFF
1234
SWITCH
SWITCH
SWITCH
OFF
OFF
OFF
OFF OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
.999 Sec.
9.99 Sec.
99.9 Sec.
999 Sec.
.999 Min.
99.9 Hr.
99.9 Min.
999 Min.
ON
ON
ON
ON
ON
ON
RANGE
2
1 3
www.multispanindia.com
No1
Supply 100 To 270V AC
No2
C1
C2
Nc1
Nc2
L
N

MENU
DIN-63
www.multispanindia.comPage-2
Running Time
1 2 3 SET VALUE
Auto Exit after 4 sec.
Auto Exit after 4 sec.
Press key OR key
Press key OR key
to change the set value
If we want to configure the instrument like 99.9 seconds & delayed
ON mode then set the DIP switches as shown in figure.
1). Configure the instrument using the DIP switch.
2). Do all connection as shown in connection diagram and turn on instrument.
3). Set the time as per requirement.
4). Press UP key & then give power fail supply display will show UP time Selection. To select UP
Timing of DOWN time Selection, Use key & Down key after 3 sec, selection will be
saved & Auto Exit.
1234
ON
For Example,
Woking

DIN-63
www.multispanindia.comPage-3
Allsafetyrelatedcodifications,symbolsandinstructionsthatappearinthisoperatingmanual
orontheequipmentmustbestrictlyfollowedtoensurethesafetyoftheoperatingpersonnelas
wellastheinstrument.
Ifalltheequipmentisnothandledinamannerspecifiedbythemanufacturer,itmightimpairthe
protectionprovidedbytheequipment.
=>Readcompleteinstructionspriortoinstallationandoperationoftheunit.
WARNING:Riskofelectricshock.
3)Cableusedforconnectiontopowersource,musthaveacrosssectionof1mmorgreater.Thesewires
shouldhaveinsulationscapacitymadeofatleast1.5kV.
2)Toreduceelectromagneticinterference,usewirewithadequateratingandtwistsofthesameof
equalsizeshallbemadewithshortestconnection.
1)TopreventtheriskofelectricshockpowersupplytotheequipmentmustbekeptOFFwhiledoingthe
wiringarrangement.Donottouchtheterminalswhilepowerisbeingsupplied.
4)Abetteranti-noiseeffectcanbeexpectedbyusingstandardpowersupplycablefor
theinstrument.
1)Donotallowpiecesofmetal,wireclippings,orfinemetallicfillingsfrominstallationtoenterthe
productorelseitmayleadtoasafetyhazardthatmayinturnendangerlifeorcauseelectricalshockto
theoperator.
2)Circuitbreakerormainsswitchmustbeinstalledbetweenpowersourceandsupplyterminalto
facilitatepowerʻONʼorʻOFFʼfunction.Howeverthismainsswitchorcircuitbreakermustbe
installedatconvenientplacenormallyaccessibletotheoperator.
3)Useandstoretheinstrumentwithinthespecifiedambienttemperatureandhumidityrangesas
mentionedinthismanual.
WarningGuidelines
InstallationGuidelines
MechanicalInstallation
Maintenance
SafetyPrecautions
1)ToinstalltheinstrumentonaDINrail,raisetheclampatthebackoftheinstrumentandplaceiton
therail.Nowreleasetheclamp,sotheinstrumentfitsontheDINrail.
2)Ensureproperfittingoftheinstrumentbypullingitoutwards.
3)ToremovetheinstrumentraisetheclamptoreleaseitfromtheDINrail.
4)Theequipmentinitsinstalledstatemustnotcomeincloseproximitytoanyheatingsource,
causticvapors,oilssteam,orotherunwantedprocessbyproducts.
5)Donotconnectanythingtounusedterminals.

1)Theequipmentshouldbecleanedregularlytoavoidblockageofventilatingparts.
2)Cleantheequipmentwithacleansoftcloth.Donotuseisopropylalcoholoranyothercleaningagent.
3)Fusibleresistormustnotbereplacedbyoperator.
2
Front view (mm)
76 76
27
85
Side view (mm)
NO L
N
C NC
NCNO C
SM
DIN 63
HRelay
9 9 9

DIN-63
www.multispanindia.comPage-4
Note
Productimprovementandupgradeisaconstantprocedure.SoformoreupdatedoperatinginformationandSupport,
PleasecontactourHelpline: orEmailat[email protected]Ver:2103+91-9081078681/83