MULTISPAN UTR-1044 User manual

UTR 2044
R
 

TIME
SET TIME
SET
ENT RESET
www.multispanindia.com
Page - 1UTR-1044,2044,444
Technical Specification
Connection Diagram
OPERATING MANUAL
PID TEMPERATURE CONTROLLER
UTC-121P,221P & 421P
OPERATING MANUAL
UNIVERSAL TIMER
UTR-1044,2044,444
Output
Power Supply
Protection Level
Operating Relative
(As per request)
Temperature Humidity
1 relay, 2 C/O contact, 230V AC, 5A
100 to 250V AC, 50 / 60 Hz, Approx 4VA
IP-65(Front side) AS per IS/IEC 60529:2001
0°C To 55°C Up to 95% RH Non Condensing
Model
Display
Size(HXWXD)
Panel Cutout
Input
UTR 1044
96 X 96 X 50 mm
68 X 68 mm
92 X 92 mm 44 X 44 mm
72 X 72 X 85 mm 48 X 48 X 70 mm
UPPER:- 4 Digit 7 seg 0.70”,red LED Display
UPPER:- 4 Digit 7 seg 0.70”,red LED Display
LOWER:- 4 Digit 7 seg 0.4”,green LED Display LOWER:- 4 Digit 7 seg 0.28”,green LED Display
UTR 2044 UTR 444
NPN/PNP Proximity & Micro Switch NPN Proximity & Micro Switch
Notes:
1). For safely purpose, key function are designed in such a way that operator will not go into
detailed parameter setting (Previously Set) function. In this situation, in LOCK parameter,
YES has to be selected. If previously set parameters are to be changed, then any operator
has to select NO.
2). POWER ON () : Timer starts counting as soon as it gets power supply.
3). By default Cycle ON Mode is provided. Please refer programming guide to change to Cycle OFF
Delay ON/ Delay OFF Mode.
!
100
250V AC
~
50/60 HZ
4VA
1
2
3
4
5
L
N
7
6
8
9
10
11
12
NC
RELAY
RESET
NC
C
NO
NO
M/S PROXI NPN
I/P
+12V
GND
~
50/60 HZ
4VA
100
250V AC
N0
N0
+12V
I/P1
I/P2
GND
M/S
NC
NC
C
C
L
N
1
2
3
4
5
6
7
8
9
10
11
12
13
14
RESET
RELAY
RELAY
PNP PROXI:-
Short Pins 5 & 6
MICRO SWITCH:-
Short Pins 5 & 6
Proxi Connection to 3, 4 & 5
M/S Connection 3 & 4
NPN PROXI:-
Short Pins 3 & 4
Proxi Connection to 4, 5 & 6
17 8 9
12
1314
10
11
1617181920 15
23456
~
50/60 HZ
4VA
100
250V AC
M/S
RESETGNDI/P2+12V I/P1
LN
NPN PROXI:- Short Pins 16 & 15
MICRO SWITCH:- Short Pins 14 & 13
Proxi Connection to 15,14 & 13
M/S Connection 16 & 15
PNP PROXI:- Short Pins 14 & 13
Proxi Connection to 16,15 & 14
NC NCC CNO NO
Relay Relay
UTR 1044
TIME
SET TIME
 

SET
ENT RESET
RESET
SET
ENT
UTR 444
SET TIME
TIME
R1
R2



Delay time (time-1)
Cycle OFF time (time-2)
press key to
set cycle Delay time
If Delayed ON/ Delayed OFF is selected
If Delayed ON/ Delayed OFF is selected
If Cycling Mode is selected
If Cycling Mode is selected
No. OF
Repeat Cycle
Cycle ON time (time-1)
press key to
set cycle ON time
press key to
set cycle OFF time
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key to save & exit
Press key for 5 to 7 sec
Time
Set Time


















  


























  

























 

Press key
Press key
Press key
Press key
Press key for mode selection
Press key for range selection
Press key for range selection
Press key for range selection
Press key for range selection
Press key for range selection
/
/
/
/
/
/
/
/
//
/
/
/
/
/
/
/
/
//
.
.
.
 ..
 ..
 ..
 ..
 ..
 ..
 .
 .
 .
 .
 .
 .



 .
 .
 .



.
.
.












Parameter Menu
www.multispanindia.com
Page - 2UTR-1044,2044,444

Page - 3 www.multispanindia.com
DESCRIPTION
Time - 1
Delayed OFF
No. of cycle to repeat
All Parameter allowed to set
Lock Parameter
Unit - 2 for Time - 2
Cycling time
Start from relay on
Minute set for Time - 1 or 2
Up counting
Memory Retain : Yes / No
Enable/ Trigger/ Power ON
DISPLAY
SR.
1
9
5
13
3
11
7
15
18
Time - 2
Unit - 1 for Time - 1
Delayed function
Seconds set for Time - 1 or 2
Direction of time counting
All Parameter Locked
Delayed ON
Start from relay off
Hour set for Time - 1 or 2
Down counting
2
10
6
14
17
4
12
8
16
19
20
21
22





















K
UTR-1044,2044,444
1). Turn ON instrument. SET time according to your requirement.
2). In running mode, upper display indicates current TIME value and lower display shows SET
time value. Relay ON or OFF controls depends on set time.
3). Relay operation is according to selection of Delay ON or Delay OFF in programming menu.
4). In cycling mode, relay will turn on for ON time (time-1) & relay will turn off for OFF time
(time-2) and this ON-OFF process will continue.
5). To reset the time, press Reset Key.
Working
Display Message And Their Meaning

Product improvement and upgrade is a constant procedure. So for more updated operating information and support,
please contact our helpline : 9978991474/76/82 or Email at [email protected] Ver:05-2017
Page - 4 www.multispanindia.com
UTR-1044,2044,444
Note