MULTISPAN UTR-433 User manual

TECHNICAL SPECIFICATION
UTR-433 Manual
UNIVERSAL TIMER
Input (Start Pulse)
Time Range
Operating Mode
Counting Direction
GENERAL SPECIFICATION:
NPN Proximity
Sec (9.99/99.9/999)
Micro Switch
Min (9.59/99.9/999)
Hour (9.59/99.9/999)
Cyclic On Timer
Delay On Timer
Cyclic Off Timer
Delay Off Timer
UP/ DOWN
Reset Option Front Panel Reset
Terminal Reset
INPUT SPECIFICATION:
OUTPUT SPECIFICATION:
Relay
Relay Type
Rating
1 nos.
2 C/O
5A, 230V AC
Relay Output
DISPLAY AND KEYS:
DIMENSION:
Display
Size
Keys
Panel Cutout
Upper: 3 digit, 7 segment, 0.80”
Lower: 3 digit, 7 segment, 0.40”
48 (H) x 48 (W) x 70 (D) mm
SET, SHIFT, INC, ENT/RST
45 (H) x 45 (W) mm
AUXILIARY SUPPLY:
Supply voltage
Power consumption
(VA RATING) Approx 4 VA @ 230V AC MAX
ENVIRONMENT CONDITION:
Relative Humidity
Protection Level
(AS Per Request)
Operating Temp. 0°C to 55°C
UP to 95% RH
(non-condensing)
IP-65 (Front side) As per IS/IEC
60529 : 2001
100 to 270V AC, 50-60Hz
Outline Dimension (mm) Panel Cutout
Dimension (mm)
TERMINAL CONNECTION
MECHANICAL INSTALLATION
Page 1
UTR 433

output indication
300
260
STATUS LED DESCRIPTION
Process Time
If Cyclic Mode selected If Delay ON/OFF Mode
selected
Set Time
Cycle ON time
Cycle OFF time
Long Press Key to enter
into parameter setting
Delay time
Change by
& Key
Change by
& Key
Change by
& Key
SET TIME SETTING
ON Time
Start Pulse
20
1510
5
Time 1( )
Time 1( ) Time 1( )
Time 1( )
Upto selected
total no. of
repeat Cycle
ON Time
CYCLIC ON
OFF Time 1 OFF Time 1
CYCLIC OFF
OFF Time
20
1510
5Upto selected
total no of
repeat Cycle
OFF Time ON Time ON Time
Delay ON
20
1510
5
Time
ON Delay
Time( )
Time( )
Delay OFF
20
1510
5
Time
OFF Delay
Time
Time
RelayRelayRelayRelay
Time 2( )
Time 2( ) Time 2( )
Time 2( )
TIMING DIAGRAM
To enter in parameter setting
mode
To reset the timer
PRESS KEYFUNCTION
OPERATOR MODE
PARAMETER SETTING MODE
Edited parameter value to be set,
And move to the next parameter
It will select the digit to modify,
When value is edited
It will change the Value of
selected digit
Set parameter to save & exit
RST
ENT
RST
ENT
KEY OPERATION
Page 2

999
999
999
999
999
999
99.9
99.9
99.9
99.9
99.9
99.9
99.9
99.9
99.9
9.99
9.99
9.99
9.59
9.59
9.59
9.59
9.59
9.59
999
999
999
Sec
Sec
Sec
Min
Min
Min
Hr.
Hr.
Hr.
If Cyclic Mode selected
No. of Repeat Cycle
If Delay ON/OFF Mode
selected
Change by & Key
Change by Key
Change by Key
Change by Key
Change by Key
Change by Key
Change by Key
Change by Key
Change by Key
Change by Key
Change by Key
Change by Key
Change by Key
To enter into parameter setting
Enter Password 25
Select Operating Mode
(Cyclic ON)
(Sec/Min/Hr.)
(Sec/Min/Hr.)
(Sec/Min/Hr.)
Unit Selection For Cycle ON Time
Unit Selection For Delay Time
Range Selection For Cycle ON Time
Range Selection For Delay Time
Range Selection For Cycle OFF Time
Time counting direction
Time counting direction
Memory Retain
Memory Retain
Start Pulse
Press key to save & exit
Press key to save & exit
Start Pulse
(Power ON/Trigger/Enable)
(Power ON/Trigger/Enable)
(Yes/No)
(Yes/No)
(UP Count/Down Count)
(UP Count/Down Count)
Unit Selection For Cycle OFF Time
(Cyclic OFF) (Delay OFF) (Delay ON)
/ / /
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
.
.
.
.
.
.
ENT
RST
ENT
RST
PARAMETER SETTING
Page 3

All safety related codifications, symbols and instructions
that appear in this operating manual or on the equipment must
be strictly followed to ensure the safety of the operating
personnel as well as the instrument.
Read complete instructions prior to installation
and operation of the unit.
WARNING : Risk of electric shock.
If all the equipment is not handled in a manner specified
by the manufacturer, it might impair the protection provided
by the equipment.
SAFETY PRECAUTION
!
1. The equipment should be cleaned regularly to avoid blockage
of ventilating parts.
2. Clean the equipment with a clean soft cloth. Do not use
isopropyl alcohol or any other cleaning agent.
3. Fusible resistor must not be replaced by operator.
MAINTENANCE
1. This equipment, being built-in-type, normally becomes a
part of main control panel and in such case the terminals
do not remain accessible to the end user after installation
and internal wiring.
2. Do not allow pieces of metal, wire clippings, or fine metallic
fillings from installation to enter the product or else it may
lead to a safety hazard that may in turn endanger life or
cause electrical shock to the operator.
3. Circuit breaker or mains switch must be installed between
power source and supply terminal to facilitate power ‘ON’
or ‘OFF’ function. However this mains switch or circuit
breaker must be installed at convenient place normally
accessible to the operator.
4. Use and store the instrument within the specified ambient
temperature and humidity ranges as mentioned in this
manual.
INSTALLATION GUIDELINES
Page 4
Note:
Specifications are subject to change, since development is a continuous process,
So for more updated operating information and Support,
Please contact our Helpline: [phone]/81 or
Email at Ver:2307[email protected]
1. Prepare the panel cutout with proper dimensions as show
above.
2. Fit the unit into the panel with the help of clamp given.
3. The equipment in its installed state must not come in close
proximity to any heating source, caustic vapors, oils steam,
or other unwanted process by products.
4. Use the specified size of crimp terminal (M3.5 screws) to
wire the terminal block. Tightening the screws on the
terminal block using the tightening torque of the range of
1.2 N.m.
5. Do not connect anything to unused terminals.
WARNING : Risk of electric shock.
1. To prevent the risk of electric shock power supply to the
equipment must be kept OFF while doing the wiring
arrangement. Do not touch the terminals while power is
being supplied.
2. To reduce electro magnetic interference, use wire with adequate
rating and twists of the same of equal size shall be made with
shortest connection.
3. Cable used for connection to power source, must have a cross
section of 1mm or greater. These wires should have insulations
capacity made of at least 1.5kV.
4. A better anti-noise effect can be expected by using standard
power supply cable for the instrument.
MECHANICAL INSTALLATION GUIDELINES
WARNING GUIDELINES