Multistore CLASSIC Series User manual

CLASSIC RANGE
Assembly InstructIons
PACK
1
Jumbo
DrAWer
1
HAngIng
rAIL
1
FIXeD
SHeLF
1
1495H x 608W x 430D
WHITE #2669938 LIgHT Oak #2683484 Dark COCO #2683522
mAXI uLtrA-HS2

ASSEMBLY INSTRUCTION FOR MAXI ULTRA HS2
2 x FIXED SHELF
1 x BOTTOM KICK
1 x FOLDED BACKING BOARD
PARTS IDENTIFICATION LIST

1 x L & R GABLE
When aaching unit to wall put safety bracket in
middle of unit with 16mm pan head screw then
25mm pan head screw into wall. For plasterboard
without a stud it is recommended to use a plug with
screw (not provided).

   
CONFIRMAT SCREWS 50mm x 5mm 
CAPS 
BACKING NAILS 
16mm WOOD SCREW 
30mm FLANGES-PER SET OF 2 
 30mmHANGING RAIL 
   
WHITE CAMS 
CAM PINS 
16mm PAN HEAD SCREWS 
 25mm PAN HEAD SCREWS 
 “L” SAFETY BRACKET 
2 x CAM SHELVES
FOLD LINE



 








FIXED SHELF KICK





-
-
INFILL
-
-
INSERT YOUR 4 PINS INTO THE
HOLE NO: THEN INSERT THE
CAMS INTO THE HOLES
PROVIDED ON YOUR SHELF .
USING SCREW DRIVER TWIST
CAM INTO LOCK POSITION.

1 x DRAWER ASSEMBLY INSTRUCTION

-


-
.
   
6CAMS 2
7CAM PINS 2
830mm 8 GAUGE SCREW 3
9EURO SCREWS 4
10 HANDLE 1
11 RUNNERS PER SET 1
   
1CONFIRMAT SCREWS 4
2DOWELS 4
3BACKING NAILS 20
45/8 X 6 WOOD SCREWS 6
5 INFILL 1
STEP 2.
GRAB YOUR FIRST SIDE AND INSERT YOUR CAMS
INTO THE HOLE PROVIDED ON THE OUTSIDE OF THE
DRAWER GENTLY AS PER INSTRUCTIONS BELOW.
PUSH THE SIDE INTO THE FRONT DOWELS & PIN THEN CAREFULLY USING A SCREW DRIVER TURN
UNTIL IT LOCKS IN. REPEAT THIS PROCESS WITH THE OTHER SIDE.
NOW PLACE YOUR LAST PIECE BETWEEN THE TWO SIDES USING THE
SCREWS NO.1 SUPPLIED SCREW INTO THE SIDES OF THE BACK
DRAWER PIECE.
IMPORTANT NOTICE:
PLACE THE FITTING OVER THE HOLE
KEEPING THE SQUARE EDGE OF THE
FITTING PARALLEL TO THE FACE OF
THE BOARD, KNOCK IN CAREFULLY.









DRAWER ASSEMBLY
C-LEFT-GABLE RUNNER












.



[phone] -



DIAGRAM 1
30. ● ●
29. ● ●
28. ● ●
27. ● ●
26. ● ●
25. ● ●
24. ● ●
23. ● ●
22. ● ●
21. ● ●
20. ● ●
19. ● 5mm HOLES ●
18. ● ●
17. ● ●
15. ● ●
15. ● ●
14. ● ●
13. ● ●
12. ● ●
11. ● ●
10. ● ●
9. ● ●
8. ● ●
7. ● ●
6. ● ●
5. ● ●
4. ● ●
3. ● ●
2. ● ●
1. ● ●
* * *
MAXI ULTRA ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
H1 1 8
HS2 1 8 – 15
H2 1 – 8 13
HS 8
MAXI ULTRA & ULTRA SERIES
Models Hole Positions Models Hole Positions
450 1-6-11-16 LSD550 1-8
315C 1-8-15-20 LSD330 1
515 1-6-11-16-21
Executive 750 ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
HS 8
H1 1 8
H2 1 – 6 11
H3 1 – 8 – 13 20
MAXI & MSM SERIES
Models Hole Positions Fixed Shelf Position
16J3 1 – 8 – 15 22
C16 1 – 8 – 15 – 20 – 25 30
C06 1 – 8 – 15 – 20 – 25 30
600J3 8 – 15 - 22
400J3 1 – 8 – 15
Executive Series
Models Hole Positions Fixed Shelf Position
EXC – 4J 1 – 8 – 15 - 22 N/A
EXC – 5C 1 – 8 – 15 – 20 – 25 N/A
EXC – 4B 8 – 16 – 24 - 32 N/A
EXC – 2B 8 – 14 N/A
EXB - 5C 1 – 8 – 15 – 20 – 25 N/A
EXB – 4J 1 – 8 – 15 – 20 N/A
EXB – 4B 8 – 16 – 22 – 28 N/A
INSTRUCTIONS FOR RUNNER PLACEMENT

Place metal runners in their correct hole posions
(see above DIAGRAM 1) making sure CL = LEFT HAND
GABLE & CR = RIGHT HAND GABLE, then aach using
the special 7.5 euro screws provided.
(see diagram to the right).

multistore.com.au
Multistore Industries (Aust) Pty Ltd
9 Nevilles Street, Underwood QLD 4119 P:[phone] [email protected]
For easy assembly instructions, please refer to video on our website: www.multistore.com.au
Versatile Storage Units
for any room