Multistore MAXI ULTRA HS2 User manual

ASSEMBLY INSTRUCTION FOR MAXI ULTRA HS2
2 x FIXED SHELF
1 x BOTTOM KICK
1 x FOLDED BACKING BOARD
PARTS IDENTIFICATION LIST

1 x L & R GABLE
When aaching unit to wall put safety bracket in
middle of unit with 16mm pan head screw then
25mm pan head screw into wall. For plasterboard
without a stud it is recommended to use a plug with
screw (not provided).

   
CONFIRMAT SCREWS 50mm x 5mm 
CAPS 
BACKING NAILS 
16mm WOOD SCREW 
30mm FLANGES-PER SET OF 2 
 30mmHANGING RAIL 
   
WHITE CAMS 
CAM PINS 
16mm PAN HEAD SCREWS 
 25mm PAN HEAD SCREWS 
 “L” SAFETY BRACKET 
2 x CAM SHELVES
FOLD LINE



 








FIXED SHELF KICK





-
-
INFILL
-
-
INSERT YOUR 4 PINS INTO THE
HOLE NO: THEN INSERT THE
CAMS INTO THE HOLES
PROVIDED ON YOUR SHELF .
USING SCREW DRIVER TWIST
CAM INTO LOCK POSITION.

1 x DRAWER ASSEMBLY INSTRUCTION

-


-
.
   
6CAMS 2
7CAM PINS 2
830mm 8 GAUGE SCREW 3
9EURO SCREWS 4
10 HANDLE 1
11 RUNNERS PER SET 1
   
1CONFIRMAT SCREWS 4
2DOWELS 4
3BACKING NAILS 20
45/8 X 6 WOOD SCREWS 6
5 INFILL 1
STEP 2.
GRAB YOUR FIRST SIDE AND INSERT YOUR CAMS
INTO THE HOLE PROVIDED ON THE OUTSIDE OF THE
DRAWER GENTLY AS PER INSTRUCTIONS BELOW.
PUSH THE SIDE INTO THE FRONT DOWELS & PIN THEN CAREFULLY USING A SCREW DRIVER TURN
UNTIL IT LOCKS IN. REPEAT THIS PROCESS WITH THE OTHER SIDE.
NOW PLACE YOUR LAST PIECE BETWEEN THE TWO SIDES USING THE
SCREWS NO.1 SUPPLIED SCREW INTO THE SIDES OF THE BACK
DRAWER PIECE.
IMPORTANT NOTICE:
PLACE THE FITTING OVER THE HOLE
KEEPING THE SQUARE EDGE OF THE
FITTING PARALLEL TO THE FACE OF
THE BOARD, KNOCK IN CAREFULLY.









DRAWER ASSEMBLY
C-LEFT-GABLE RUNNER












.



[phone] -



DIAGRAM 1
30. ● ●
29. ● ●
28. ● ●
27. ● ●
26. ● ●
25. ● ●
24. ● ●
23. ● ●
22. ● ●
21. ● ●
20. ● ●
19. ● 5mm HOLES ●
18. ● ●
17. ● ●
15. ● ●
15. ● ●
14. ● ●
13. ● ●
12. ● ●
11. ● ●
10. ● ●
9. ● ●
8. ● ●
7. ● ●
6. ● ●
5. ● ●
4. ● ●
3. ● ●
2. ● ●
1. ● ●
* * *
MAXI ULTRA ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
H1 1 8
HS2 1 8 – 15
H2 1 – 8 13
HS 8
MAXI ULTRA & ULTRA SERIES
Models Hole Positions Models Hole Positions
450 1-6-11-16 LSD550 1-8
315C 1-8-15-20 LSD330 1
515 1-6-11-16-21
Executive 750 ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
HS 8
H1 1 8
H2 1 – 6 11
H3 1 – 8 – 13 20
MAXI & MSM SERIES
Models Hole Positions Fixed Shelf Position
16J3 1 – 8 – 15 22
C16 1 – 8 – 15 – 20 – 25 30
C06 1 – 8 – 15 – 20 – 25 30
600J3 8 – 15 - 22
400J3 1 – 8 – 15
Executive Series
Models Hole Positions Fixed Shelf Position
EXC – 4J 1 – 8 – 15 - 22 N/A
EXC – 5C 1 – 8 – 15 – 20 – 25 N/A
EXC – 4B 8 – 16 – 24 - 32 N/A
EXC – 2B 8 – 14 N/A
EXB - 5C 1 – 8 – 15 – 20 – 25 N/A
EXB – 4J 1 – 8 – 15 – 20 N/A
EXB – 4B 8 – 16 – 22 – 28 N/A
INSTRUCTIONS FOR RUNNER PLACEMENT

Place metal runners in their correct hole posions
(see above DIAGRAM 1) making sure CL = LEFT HAND
GABLE & CR = RIGHT HAND GABLE, then aach using
the special 7.5 euro screws provided.
(see diagram to the right).

WARRANTY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entled to
a replacement of refund for major failure.
10 Year Warranty
• If the purchaser has a fault or defect with this product, the purchaser needs to contact Mulstore Industries
(Aust) directly on [phone] and state date of purchase, place of purchase and proof of purchase.
• Mulstore Industries (Aust) will replace any faulty or defect parts at no cost to the customer. A replacement
will be sent to you as soon as possible, or product can be exchanged at the store of purchase.
• This warranty is in addion to other rights and remedies of the customer under law.
Sincerely,
Mulstore Industries (Aust) Management