Multistore mAXI-C16 User manual

Assembly InstructIons
CLASSIC rAnge
PACKS
2
Jumbo
DrAWerS
2
ADJuStAbLe
SHeLF
1
StAnDArD
DrAWerS
3
1650H x 608W x 450D
WHITE #0027257 LIgHT Oak #2683505 Dark COCO #2683543
mAXI-C16

TOP of UNIT
When aaching unit to wall put safety bracket in
middle of unit with 16 Pan head screw then 25mm
Pan head screw into wall.
For plasterboard without a stud it is recommended
to use a plug with screw (not provided).
ASSEMBLY INSTRUCTION FOR MAXI & MSM C16
PARTS IDENTIFICATION LIST
NO MODEL DESCRIPTION QTY
1CONFIRMAT SCREWS 20
2CAPS 20
3BACKING NAILS 75
4HANDLES 5
NO MODEL DESCRIPTION QTY
5SHELF PINS 4
6BRACKETS 1
7BRACKET UNIT SCREW 1
8BRACKET WALL SCREW 1

PROCEED TO UN-FOLD YOUR BACK BOARD AND
PROCEED TO NAIL IT INTO POSITION MAKING
SURE YOU ARE SQUARE AND ON THE EDGE AT
ALL TIMES.
STAND YOUR UNIT UP AND PROCEED TO INSERT YOUR ADJUSTABLE SHELVING.
PUSH THE 4 SHELF PINS INTO THE HOLES PROVIDED (5) ON EITHER SIDE FOR YOUR SHELF TO SIT ON, THE BEST WAY TO DO
THIS IS TO COUNT YOUR HOLES UP FROM THE BOTTOM SO YOUR SHELF WILL BE LEVEL.
YOU MAY CHOOSE WHERE YOU WOULD LIKE THESE TO SIT.
PROCEED TO PART 2
FOR INSTRUCTIONS ON HOW TO
ASSEMBLE YOUR DRAWERS

HOW TO ASSEMBLE YOUR 5—DRAWER
STEP1.
LAYOUT YOUR DRAWER PIECES FLAT AS PER DESIGN WITH PRE-DRILLED HOLES FACING UP.
START WITH THE BACK OF THE FRONT DRAWER AND PLACE YOUR DOWELS & CAM PIN IN THE
PRE-DRILLED HOLES ON EITHER SIDE AS INSTRUCTED BELOW.
NO MODEL DESCRIPTION QTY
1CONFIRMAT SCREWS 20
2DOWELS 20
3BACKING NAILS 100
45/8 X 6 WOOD SCREWS 30
5 HANDLES 5
NO MODEL DESCRIPTION QTY
6CAMS 10
7CAM PINS 10
830mm 8 GAUGE INFILL SCREW 3
9EURO SCREWS 20
10 INFILL 1
11 RUNNERS PER SET 5
STEP 2.
GRAB YOUR FIRST SIDE AND INSERT YOUR CAMS
INTO THE HOLE PROVIDED ON THE OUTSIDE OF THE
DRAWER GENTLY AS PER INSTRUCTIONS BELOW.
PUSH THE SIDE INTO THE FRONT DOWELS & PIN THEN CAREFULLY USING A SCREW DRIVER
TURN UNTIL IT LOCKS IN. REPEAT THIS PROCESS WITH THE OTHER SIDE.
NOW PLACE YOUR LAST PIECE BETWEEN THE TWO SIDES USING THE
SCREWS NO.1 SUPPLIED SCREW INTO THE SIDES OF THE BACK DRAWER
PIECE.
IMPORTANT NOTICE:
PLACE THE FITTING OVER THE HOLE
KEEPING THE SQUARE EDGE OF THE
FITTING PARALLEL TO THE FACE OF
THE BOARD, KNOCK IN CAREFULLY.

PICTURE OF YOUR FINISHED
STEP 5.
USING THE HANDLE SCREW (NO:6) ATTACH THE HANDLE TO THE
BACK OF THE DRAWER. FRONT INTO THE PREDRILLED HOLES ALL
READY PROVIDED.
DRAWER ASSEMBLY
STEP 6.
PLACE YOUR DRAWER RUNNER ON THE BOTTOM OF THE
DRAWER USING THE WOOD SCREWS PROVIDED (No:4)
SCREW TWO INTO EACH RUNNER. REPEAT FOR THE OTH-
ER SIDE.
STEP 3.
YOUR DRAWER SHOULD BE FACING
DOWN WITH THE FRONT DRAWER
EXSPOSING THE CUTOUT FOR THE
BASE TO BE PUSHED INTO FACE DOWN
WITH THE BROWN SIDE SHOWING. MAK-
ING SURE YOU HAVE THE DRAWER
SQUARE, PROCEED TO NAIL DOWN THE
BASE SPACING THEM OUT AROUND THE
EDGE OF THE THREE SIDES.
PLACE YOUR RUNNERS INTO THE
DESIGNATED HOLES MAKING SURE THE
WHEEL IS FACING TO THE FRONT OF THE
GABLE. HOLE POSITION NO 1,8 AND 15.
YOUR DRAWER RUNNER WILL HAVE THE
WHEEL TO THE BACK OF THE DRAWER.
STEP 4

DIAGRAM 1
30. ● ●
29. ● ●
28. ● ●
27. ● ●
26. ● ●
25. ● ●
24. ● ●
23. ● ●
22. ● ●
21. ● ●
20. ● ●
19. ● 5mm HOLES ●
18. ● ●
17. ● ●
15. ● ●
15. ● ●
14. ● ●
13. ● ●
12. ● ●
11. ● ●
10. ● ●
9. ● ●
8. ● ●
7. ● ●
6. ● ●
5. ● ●
4. ● ●
3. ● ●
2. ● ●
1. ● ●
* * *
MAXI ULTRA ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
H1 1 8
HS2 1 8 – 15
H2 1 – 8 13
HS 8
MAXI ULTRA & ULTRA SERIES
Models Hole Positions Models Hole Positions
450 1-6-11-16 LSD550 1-8
315C 1-8-15-20 LSD330 1
515 1-6-11-16-21
Executive 750 ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
HS 8
H1 1 8
H2 1 – 6 11
H3 1 – 8 – 13 20
MAXI & MSM SERIES
Models Hole Positions Fixed Shelf Position
16J3 1 – 8 – 15 22
C16 1 – 8 – 15 – 20 – 25 30
C06 1 – 8 – 15 – 20 – 25 30
600J3 8 – 15 - 22
400J3 1 – 8 – 15
Executive Series
Models Hole Positions Fixed Shelf Position
EXC – 4J 1 – 8 – 15 - 22 N/A
EXC – 5C 1 – 8 – 15 – 20 – 25 N/A
EXC – 4B 8 – 16 – 24 - 32 N/A
EXC – 2B 8 – 14 N/A
EXB - 5C 1 – 8 – 15 – 20 – 25 N/A
EXB – 4J 1 – 8 – 15 – 20 N/A
EXB – 4B 8 – 16 – 22 – 28 N/A
INSTRUCTIONS FOR RUNNER PLACEMENT
* = FIXED SHELF HOLES & KICK
Place metal runners in their correct hole posions
(see above DIAGRAM 1) making sure CL = LEFT HAND
GABLE & CR = RIGHT HAND GABLE, then aach using
the special 7.5 euro screws provided.
(see diagram to the right).

multistore.com.au
Multistore Industries (Aust) Pty Ltd
9 Nevilles Street, Underwood QLD 4119 P:[phone] [email protected]
For easy assembly instructions, please refer to video on our website: www.multistore.com.au
Versatile Storage Units
for any room