Multistore EXC-750H2 User manual

Assembly InstructIons
eXeCutIve rAnge
PACKS
2
StAnDArD
DrAWerS
2
HAngIng
rAIL
1
FIXeD
SHeLF
1
2000H x 750W x 450D
WHITE #2669935 LIgHT Oak #2683481 Dark COCO #2683519
eXC-750H2

ASSEMBLY INSTRUCTION FOR EXC-750 H2
PARTS IDENTIFICATION LIST
2 x TOP GABLES
2 x BOTTOM GABLES
2 x BACKING BOARDS
2 x FIXED SHELF
1 x 30mm 710 HANGING RAIL
1 x BOTTOM KICK
1 x CAM SHELF
NO MODEL DESCRIPTION QTY
1CONFIRMAT SCREWS 50mm x 5mm 14
2CAPS 14
3DOWELS 4
4BACKING NAILS 75
5RAIL FLANGES 2
NO MODEL DESCRIPTION QTY
6WHITE CAMS 4
7CAM PINS 4
816mm PAN HEAD SCREWS 1
925mm PAN HEAD SCREWS 1
10 “L” SAFETY BRACKET 1
1 x 717mm H MOULD
When aaching unit to wall put safety bracket in
middle of unit with 16mm pan head screw then
25mm pan head screw into wall.
For plasterboard without a stud it is recommended
to use a plug with screw (not provided).
TOP of UNIT
1035mm x 445m x 16mm
966mm x 445m x 16mm
718mm x 445mm x 16mm
718mm x 61 x 16mm
718mm x 445mm x 16mm
975mm x 744 x 3
TOP
FOLD LINE
BOTTOM
962mm x 744 x 3
FOLD LINE

RAIL SUPPORT
BRACKETS DOWELS FIXED SHELF KICK
TAKE YOUR GABLES AND LAY THEM OUT
FLAT, YOU SHOULD HAVE 2 X TOP &
2 X BOTTOM GABLES. USING A LITTLE
WOOD GLUE (NOT SUPPLIED) IN YOUR
PRE-DRILLED HOLES, INSERT YOUR
WOOD DOWELS INTO 2 OF THE HOLES
AND PUSH YOUR TOP INTO YOUR
BOTTOM GABLE.
NEXT STEP:
YOU WILL NEED TO RETRIEVE THE INFILL FROM PART 2, USING 30mm
8 GAUGE SCREWS PROVIDED, ATTACH THE INFILL TO THE UNDER-SIDE
OF THE CAM SHELF BEFORE PUTTING YOUR SHELF INTO PLACE.
ALIGN YOUR SHELVES AND KICK TO THE LEFT-HAND GABLE, SCREW THEM INTO
PLACE ATTACH YOUR RIGHT-HAND GABLE AND DO THE SAME.
FOLD OUT BOTH TOP AND BOTTOM BACKS, PROCEED TO NAIL HALF OF THE
BOTTOM BACK AND HALF OF THE TOP BACK THEN SLIDE THE ‘’H’’ MOULD INTO
BOTH BACKS TO JOIN THEM TOGETHER IN THE MIDDLE.
PROCEED TO NAIL THEM INTO POSITION MAKING SURE YOU ARE STILL SQUARE.
YOU WILL NEED 2 X 16mm WOOD
SCREWS FOR THE NEXT STEP.
TAP INTO POSITION YOUR FLANGES
INTO THE HOLES PROVIDED IF YOU
WISH YOU CAN SCREW IN 1 SCREW
INTO THE MIDDLE OF THE FLANGE
AND SLIDE ON YOUR HANGING RAIL.
NEXT:-YOUR PART 2 IS REQUIRED
YOU WILL NEED THE DRAWER
ASSEMBLY SHEET ON HOW TO
CREATE YOUR DRAWER.
“H” MOULD
IN PART 2 INSERT YOUR 4 PINS (7) INTO
THE HOLE NO: (11) PROVIDED.
INSERT THE CAMS INTO THE
HOLES PROVIDED ON THE
BOTTOM OF THE SHELF.
USING SCREW DRIVER TWIST
CAM INTO LOCK POSITION.

DRAWER INSTRUCTIONS TO SUIT EXC-750 H2 UNITS
STEP 1.
LAYOUT YOUR DRAWER PIECES FLAT AS PER DESIGN WITH
PRE-DRILLED HOLES FACING UP.
START WITH THE BACK OF THE FRONT DRAWER AND PLACE
YOUR DOWELS & CAM PIN IN THE PRE-DRILLED HOLES ON
EITHER SIDE AS INSTRUCTED BELOW.
NO MODEL DESCRIPTION QTY
1CONFIRMAT SCREWS 8
2DOWELS 8
3BACKING NAILS 75
416mm WOOD SCREWS 12
5 INFILL 1
NO MODEL DESCRIPTION QTY
6CAMS 4
7CAM PINS 4
8EURO SCREWS 8
930mm COUNTER SUNK WOODSCREW 6
10 HANDLE 2
11 DRAWER RUNNERS PER SET 2
STEP 2.
GRAB YOUR FIRST SIDE AND INSERT YOUR CAMS INTO THE HOLE PROVIDED ON THE OUTSIDE OF THE DRAWER SIDE
GENTLY AS PER INSTRUCTIONS BELOW.
IMPORTANT NOTICE:
PLACE THE FITTING OVER THE HOLE
KEEPING THE SQUARE EDGE OF THE
FITTING PARALLEL TO THE FACE OF THE
BOARD, KNOCK IN CAREFULLY.
PUSH THE SIDE INTO THE FRONT DOWELS & PIN AND THEN CAREFULLY USING A
SCREW DRIVER TURN UNTIL IT LOCKS IN. REPEAT THIS PROCESS WITH THE OTHER
SIDE.
NOW PLACE YOUR LAST PIECE BETWEEN THE TWO SIDES USING THE SCREWS: NO 1
SUPPLIED, SCREW INTO THE SIDES OF THE BACK DRAWER PIECE.

DRAWER ASSEMBLY
STEP 4.
USING THE HANDLE SCREW (NO:4) ATTACH THE HANDLE TO THE BACK OF THE DRAWER FRONT INTO THE PRE-DRILLED
HOLES ALREADY PROVIDED.
PICTURE OF YOUR FINISHED DRAWER
STEP 5.
PLACE YOUR DRAWER RUNNER ON THE BOTTOM OF THE
DRAWER FLUSH WITH THE BACK OF DRAWER, THEN USING THE
WOOD SCREWS PROVIDED No: 4 SCREW TWO INTO EACH RUN-
NER . REPEAT FOR THE OTHER SIDE.
STEP 3.
YOUR DRAWER SHOULD BE FACING DOWN WITH THE FRONT DRAWER
EXPOSING THE CUT OUT FOR THE BASE TO BE PUSHED INTO FACE
DOWN WITH THE BROWN SIDE SHOWING. MAKING SURE YOU HAVE
THE DRAWER SQUARE, PROCEED TO NAIL DOWN THE BASE SPACING
THEM OUT AROUND THE EDGE OF THE THREE SIDES.

INSTRUCTIONS FOR RUNNER PLACEMENT AND
DRAWER BOX ASSEMBLY
IMPORTANT
CABINET RUNNERS ARE MARKED AS FOLLOWS
C L = LEFT HAND SIDE
C R = RIGHT HAND SIDE
SEE DIAGRAM 2 BELOW
EXECUTIVE 750 SERIES
Models Hole Positions
EXC -750 H1 1
EXC -750 H2 1 – 6
EXC -750 H3 1 – 6 - 11
RUNNER PLACEMENT
7.5mm EURO SCREW
NOTE: MAKE SURE COR-
RECT HOLES ARE USED.
EG:- LEFT HAND SIDE RUNNER
DIAGRAM 2
Place metal runners in their correct hole positions
(see above) making sure CL = LEFT HAND GABLE
&
CR = RIGHT HAND GABLE, then attach using the
special 7.5mm euro screws provided.
SEE DRAWER ASSEMBLY
LEFT HAND CABINET GABLE
BOTTOM

multistore.com.au
Multistore Industries (Aust) Pty Ltd
9 Nevilles Street, Underwood QLD 4119 P:[phone] [email protected]
For easy assembly instructions, please refer to video on our website: www.multistore.com.au
Versatile Storage Units
for any room