Multistore MAXI ULTRA H2 User manual

ASSEMBLY INSTRUCTION FOR MAXI ULTRA H2
1x CAM SHELF
2x FIXED SHELF
1 BOTTOM KICK
. . . . . .
1x …….BACKING
1x …….BACKING
PARTS IDENTIFICATION LIST
. . . . . .
. . . . . .
. . . . . .
1x 30mm HANGING RAIL
When aaching unit to wall put safety bracket in
middle of unit with 16mm pan head screw then
25mm pan head screw into wall. For plasterboard
without a stud it is recommended to use a plug with
screw (not provided).
TOP of UNIT
4
NO MODEL DESCRIPTION QTY
1CONFIRMAT SCREWS 50mm x 5mm 15
2WHITE CAPS 15
3DOWELS 4
4BACKING NAILS 60
516mm WOOD SCREW 2
NO MODEL DESCRIPTION QTY
6CAMS 4
7CAM PINS 4
816mm PAN HEAD SCREWS 1
925mm PAN HEAD SCREWS 1
10 “L” SAFETY BRACKET 1

FOLD OUT BOTH TOP AND BOTTOM BACKS
PROCEED TO NAIL THEM INTO POSITION
MAKING SURE YOU ARE SQUARE.
THERE IS NO SCREWS NEEDED
FOR THE NEXT STEP.
TAP INTO POSITION YOUR
FLANGES INTO THE HOLES
PROVIDED AND INSERT YOUR
HANGING RAIL.
YOUR UNIT IS NOW READY TO
BE PUT INTO PLACE.
NEXT. GO TO YOUR DRAWER
ASSEMBLY SHEET ON HOW TO
CREATE YOUR DRAWER.
PLACE YOUR RUNNERS INTO THE
DESIGNATED HOLES MAKING SURE YOU
HAVE THE RUNNER FACING TO THE FRONT.
Take your gables and lay them out at you should have 2 Top &
2 Boom gables.
Using a lile of wood glue (NOT SUPPLIED) in your pre-drilled
holes, insert your Wood Dowels into 2 of the holes and push
your top into your boom gables.

HOW TO ASSEMBLE YOUR DRAWER
STEP 1.
LAYOUT YOUR DRAWER PIECES FLAT AS PER DESIGN WITH PRE-DRILLED HOLES FACING UP.
START WITH THE BACK OF THE FRONT DRAWER AND PLACE YOUR DOWELS & CAM PIN IN THE
PRE-DRILLED HOLES ON EITHER SIDE AS INSTRUCTED BELOW.
STEP 2.
GRAB YOUR FIRST SIDE AND INSERT YOUR CAMS INTO THE HOLE PROVIDED ON THE OUTSIDE OF THE DRAWER SIDE
GENTLY AS PER INSTRUCTIONS BELOW.
IMPORTANT NOTICE:
PLACE THE FITTING OVER THE HOLE
KEEPING THE SQUARE EDGE OF THE
FITTING PARALLEL TO THE FACE OF THE
BOARD, KNOCK IN CAREFULLY.
PUSH THE SIDE INTO THE FRONT DOWELS & PIN AND THEN CAREFULLY USING A
SCREW DRIVER TURN UNTIL IT LOCKS IN. REPEAT THIS PROCESS WITH THE OTHER
SIDE.
NOW PLACE YOUR LAST PIECE BETWEEN THE TWO SIDES USING THE SCREWS: NO 1
SUPPLIED, SCREW INTO THE SIDES OF THE BACK DRAWER PIECE.

PICTURE OF YOUR FINISHED DRAWER
STEP 3.
USING THE HANDLE SCREW (NO:6) ATTACHED THE HANDLE TO THE BACK OF THE DRAWER
FRONT INTO THE PREDRILLED HOLES ALLREADY PROVIDED.
DRAWER ASSEMBLY
STEP 4.
PLACE YOUR DRAWER RUNNER ON THE BOTTOM OF THE
USING THE ……….SCREWS DRILL INTO YOUR DRAWER
AND REPEAT FOR THE OTHER SIDE.
WARRANTY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entled to a
replacement of refund for major failure.
10 Year Warranty
• If the purchaser has a fault or defect with this product, the purchaser needs to contact Mulstore Industries
(Aust) directly on [phone] and state date of purchase, place of purchase and proof of purchase.
• Mulstore Industries (Aust) will replace any faulty or defect parts at no cost to the customer. A replacement
will be sent to you as soon as possible, or product can be exchanged at the store of purchase.
• This warranty is in addion to other rights and remedies of the customer under law.
Sincerely,
Mulstore Industries (Aust) Management