NAMCO Rave Racer Quick start guide

namco @ America Inc.
RIDGE RACER 2TM
ONE and TWO-PLAYER
UPGRADE KIT MANUAL

namco a
RIDGE RACER T
RAVE RACER”
Upgrade Kit Manual
Table of Contents
1 .O SPECIFICATIONS-------------- ---___-________l__l_____l_____l____ 1
1.1 Conversion Game Specifications----------------------------------- 1
1.2 Kit Specifications------ --___--_-_-__-______-- 1
1.3 Game Conversion Overview WI --- 1
2.0 INTRODUCTION- -- -------------- 1
3.0 lNSTALLATlON-------------- --_--l-_-l___-______----l-l--l--l----------- 1
3.1 Precautions ~~~~11~~--- ---o---------1--------- 1
3.2 Game Installation------- --------- -__-_--- ------- 2
3.3 Cabinet Graphics-------- -----------------I-- 3
3.4 Linked Game Operation-- --em-m-p-11 4
Figure 1: Linked Game Diagrams * ------ -4
3.5 Power-Up and Initialization- ------e- -5
Figure 2: Adjustment (Initialization) Screen ---1-_-_-_--_1--____--1_-I- 5
Figure 3: Test Mode Screen- -m-I-m -_____-_ - 6
Figure 4: Check Screen---- ---1-_-----_-__------- 7
Figure 5: Coin Options Screen-- _-__ - -________ - --------_____ -__- -- 8
Figure 6: Game Options Screen (I/2)
-----v------I maImae _ sImm -
9
Figure 7: Game Options Screen (2/z)-- -____ ----_- -_-___-____ - --_-
9
Game Options --1-11----- ------_- _________1___1__1___I_____ - _____10
Figure 8: l/O Test Screen----------- -- ---- -1-11 eml__e___aamelmelw 11
Figure 9: Switch Test Screen----------- _____-_____ -_
12
Monitor Screens- -- --- ----- -__- am_amm-me__Im 13
Figure 10: Sound Test Screen---------- ------- ---- --11- 14
Figure 11: ADS DATA Screen (112) -------- ---- 15
Figure 12: ADS DATA Screen (2/2) -111-------1---15
Figure 13: Others Screen ------ I--___- _a_-_ -__ 16
Figure 14: l/O Board Test Screen _--l___-___--l-__-___-_---I-------
16
Figure 15: MPWDSP Board Test------ ----- -mw-m-____I_--me---- 17
I

RIDGE RACER P
namco @
Upgrade Kit Manual
RAVE RACERTM
4.0 RAVE RACER GAME FEATURES
_____-_____1____________I_______________------------
18
4.1 Linked play _____-____-____ - -___ - _____ - _-__ --___-_-_--__ - _-__ - ____-___ - _______18
4.2 Solo play ___-____-___________ - -__________-__ ------____ --_----- -__ --_- --__ 19
4.3 New Features ____-____-___- -__~__-__~~~~I~~~~~~~~ ____-__----__---_________l____l_
19
APPENDIX A: PARTS LIST AND ILLUSTRATIONS
II

namco e
RAVE RACER”
1 .O SPECIFICATIONS
1.1
Conversion Game Specifications
Power Supply:
Monitor:
RIDGE RACER 2’”
Upgrade Kit Manual
Switching Power Supply, 200W
1 Standard 25” or 27” color monitor
1.2 Kit Specifications
Part No. RVOI -04432-00
1
PCB ROM Kits 2 ea. ’
Harness adapters
2 ea.
Marquee 1 ea.
Decals 1 set
1.3
Game Conversion Overview
The Rave Racer upgrade kit consists of new Rave Racer PCB components, wire harness
adapter cables, new marquee and decals. The kit can be installed in either the original
RR2 two-player cabinet or the RR2 single-player upright cabinet.
Note: Each Rave Racer upgrade kit contains parts to convert TWO driver positions
2.0 INTRODUCTION
This manual provides installation instructions for the Rave Racer upgrade kit. inspect the
kit contents, compare against the parts list in the back of this manual, and notify your
distributor and/or shipping carrier about any missing or damaged parts.
3.0 INSTALLATION
3.1 Precautions
1.
2.
Before replacing any parts, turn the AC power OFF and unplug the game.
The game’s video monitor chassis, when exposed, presents a HIGH
VOLTAGE shock hazard. If it becomes necessary to work in the back of the
game while the power is on, use extreme care to avoid touching the monitor.

RIDGE RACER 2”
namco Q
Upgrade Kit Manual RAVE RACER-
3.2 Game Installation
1.
2.
3.
4.
9.
10.
11.
Verify that power has been removed from the game.
Open the rear door to gain access to the 110 PCB (on top of the card cage).
Refer to the wiring diagram for your game in the back of this manual. Locate
the 50-pin connector, J402.
Add connections for the VIEW CHANGE switch: Remove the 50-pin
connector at J402 (on the I/O PCB) and insert the Molex-type pins (from new
cable harness RV50-04365-00) into A5 and A6 (of the 50-pin connector), with
the WHITE wire going to A5 and the BUCK wire going to A6. Refer to
drawing RV50-04400-00.
Reconnect the 50-pin connector to J402.
Remove the control panel to add the VIEW CHANGE button.
Drill a 7/8” hole to the left of the steering wheel.
Install the VIEW CHANGE button. Tighten the nut before snapping the lamp
assembly into place.
Connect the quick-disconnect lug from the WHITE wire (of new harness,
RV50-04364-00) to the gold pin designated NO (pin 4, Normally Open) of the
lamp assembly.
Connect the quick-disconnect lug from the BLACK wire to the silver pin
(designated COM) of the lamp assembly.
While reinstalling the control panel, connect the two-pin plug of the new VIEW
CHANGE harness to the plug on the PCB harness added in Step 4.
2

nanmom
RIDGE RACER T
RAVE RACER”
Upgrade Kit Manual
IO. Remove the System 22 PCB set from the rear of each unit, using care to
prevent damage to the wiring or connectors.
CAUTION:
USE ANTI-STATIC PROTECTION FOR THE FOLLOWING WORK ]
11.
12.
On each game, remove the EMI cover from the PCB rack and set it aside.
Remove the CPU and Video main boards from the card cage and place them
on a flat, anti-static surface.
13.
14.
Observe the 10 devices and 2 PCBs which are supplied with the kit. Remove
the corresponding devices and (smaller of the two) PCB from the main CPU
board. Remove the (larger of the two) PCB from the Video board.
Install the new devices and PCBs from the kit.
Note: Install device C388 in previously empty socket
12R (Key custom) on the CPU board.
15. Carefully reassemble the card cages, and reinstall them in the game cabinet,
making sure that all connectors are properly seated.
16.
Remove the original marquee plastic panel and replace with the new acrylic
Rave Racer marquee.
13. Perform game initialization per Section3.5, Power-Up and Initialization.
3.3 Cabinet Graphics
1. Install the cabinet graphics provided. Float the graphics on by applying a
spray of ammonia cleaner to each surface. Smooth out the bubbles and
liquid with a paint squeegee. Wipe the decal dry with a soft cloth.

RIDGE RACER 2’”
Upgrade Kit Manual
namco *
RAVE RACER-
3.4 Linked Game Operation
It is possible to link up to eight RAVE RACER driver positions together.
The linking procedure is the same as that used on Ridge Racer 2:
1. Turn OFF the main AC power to the game.
2. Remove the link cables from the kit or cash box.
3. Using the link cables, connect the cabinets as shown in Figure 1
Note: The switch settings shown apply to the Ridge
Racer 2 two-player cabinet. Ridge Racer 2 single-
player upright cabinet requires the addition of optional
1 P Link PCB p/n VG03-04270-00.
4.
5.
6.
Be careful not to pull on the cables while working around the rear of the
cabinet.
Turn ON the main AC power.
Refer to section TEST MODE, Game Options, for instructions on how to set
up the “CPU Number” and car type/color for each of the linked driver
positions.
w-
Connecting three 5etf
Q-
Connecting four sets Figure 1
4

namco 0
RAVE RACER’”
RIDGE RACER 2”
3.5 Power-Up and Initialization
The following procedure should always be performed at the time of initial power-up, or
when any of these components have been removed or replaced:
l Game PCBs
. ROMS
0 Steering system potentiometers
l Pedal assembly potentiometers ‘
1.
System initialization is performed as follows:
a. Open the coin door to gain access to the Service Panel.
b. Center the steering wheel and remove hands/feet from the controls.
C. While pressing the SERVICE button, toggle the TEST switch ON.
d. The ADJUSTMENT screen will appear as shown in Figure 2.
ADJUSTMENT
HANDLE 000x
GAS 000x
BRAKE 000x
Figure 2: Adjustment (Initialization) Screen
e. Controls are properly biased when values are as close to ‘0000’ as
possible.
f. Release the SERVICE button and toggle the TEST switch OFF.
5

RIDGE RACER 2- namco m
Upgrade Kit Manual RAVE RACER-
2. Turn the TEST switch ON and the TEST MODE screen, as in Figure 3, will
appear.
ITEST MODE I
CHECK
COIN OPTIONS
GAME OPTIONS
110 TEST
MONITOR TEST
SOUND TEST
ADS DATA
OTHERS
(1) Status 2% test screen (see fig. 4)
(2) Sets game cost
(3) Sets game options
(4) Switch test, etc.
(5) Screen test
(6) Adjust speakersvolume
(7) Displays accumulated game data
(8) Board test and EEPROM clear
\ ’
Figure 3: Test Mode Screen

namco @ RIDGE RACER 2m
RAVE RACER”
A. Select the CHECK screen option by turning the steering wheel, and call
up the screen by stepping on the accelerator.
CHECK
(DEFAULT IN GREEN)
FEEDBACK STEERING OFF
VIEW SWITCH OFF
STEERING 0000
SHIFT CENTER
SWITCH f OFF
SWITCH 2 OFF -
EXIT
Not applicable
Ridge Racer
- Status ON/OFF
- (4
-
Status ON/OFF,
UP/DOWN/CENTER
Figure 4: Check Screen
RIDGE RACER 2 Conversion
(4
Note: Steering’status will show full scale reading +FFFF in the CW
direction and -FFFF in the CCW direction, and “OK” if steering passes
the displacement test.
Select the desired option using the steering wheel, and use the the
accelerator to change the value of the option. Use the EXIT option (or press
the accelerator and brake simultaneously) to return to the TEST MODE main
menu.