Namco Ace driver victory lap User manual

Operators Manual

ITIS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY AT

ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL

ARE FOLLOWED PRECISELY,

Part No. 90500024

No part of this publication may be reproduced by any mechanical, photographic or electronic

process, or in the form of phonographic recording, nor may it be stored in a retrieval system,

transmitted or otherwise copied for public or private use, without permission from

NAMCO EUROPE LIMITED

While the information contained in this manual is given in good faith and was accurate at the

time of publication, NAMCO EUROPE LIMITED reserve the right to make changes and

alterations without notice.

This machine has been manufactured in accordance with European Community directives

(1st. January 1996), and as such bears the marking. Any changes or modifications to this

machine must be in accordance with European Community directives (1st. January 1996).

If you make any unauthorised changes to this product, you may contravene European

Community directives (1st. January 1996).

Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic

discharge or mains borne transients, some degradation of performance may occur. However

the machine will recover normal performance once the source of interference has ceased or

been removed.

Published by:

NAMCO EUROPE LIMITED

Namco House,

8 Acton Park Estate,

The Vale,

London W3. 7QE

Phone: 0208-324-6000

Fax:-0208-324-6010

SAFETY WARNING

Inordertousethismachinesafely, be sure to read this operators manual carefully

before installation, adjustment or use of this machine.

Whenevertheownerofthismachineentrusts disassembly, installation, adjustment

orroutine maintenance to another person, the owner should ensure that that person

readtheappropriateprecautions and relevant sections of this manual before starting

work.

In order that no accidents occur when the machine is in operation, strictly

follow the notes on safety described below. Also, carefully read section (2),

"Precautions".

Warnings for Operation ( Requirements)

NOTE:

Only operate this machine after checking that it has been installed correctly

and in accordance with the Installation and Commissioning Manual.

NOTE:

Parts of this machine move during game play, so there are places where the

distancebetweenthe stationary section and moveablesectionchanges.There

are warning notices to keep hands and feet clear of moving parts, however if

the operator feels that a person is in any danger, he should warn that person

accordingly.

NOTE:

The warning notices must always be kept in good condition and replaced if

worn, so that the customer can read them clearly.

NOTE:

If there is an error or problem with the machine, operation must be

stopped immediately and the problem rectified before any further use.

NOTE:

Installation,Service,AdjustmentsandRoutineMaintenanceshouldbecarried

out by qualified personnel only.

Warnings for Disassembly, Installation, Routine Maintenance and Troubleshooting.

DANGER:

Namco Ltd. bears absolutely no responsibility for accidents, injury or damage

resulting from unauthorized changes to this machine.

DANGER:

Ensure that the machine has been turned OFF before making adjustments or

carryingoutmaintenance.Alsoensureonlyqualifiedpersonnelturnthepower

ON to this machine.

DANGER:

The power supply and inside the monitor will remain hot and have areas of

high voltage even though the machine has been turned OFF, and there is the

possibility of burns or electric shock. Be careful not to touch these areas.

DANGER:

In order to prevent injury due to mis-operation, be sure that the voltage of the

main power supply is within the prescribed limits. Also to prevent possible

electric shock due to failure, this machine MUST be fitted with a securely

connected earthed plug.

NOTE:

Do not turnthe power switch ON untilthe machine has been installed correctly.

Contents

Operators Manual............................................................................................1

SAFETY WARNING .......................................................................................... 3

1.SPECIFICATIONS.....................................................................................5

2.PRECAUTIONS.........................................................................................6

2-1Cautions when Transporting.................................................................................6

2-2Cautions when Handling.......................................................................................6

2-3Cautions when Operating......................................................................................6

2-4Cautions when Installing.......................................................................................7

3.HOW TOPLAY..........................................................................................8

4.MAJOR COMPONENTS.........................................................................10

5.INSTALLATION.......................................................................................11

5-1Connecting the Seat Assemblies to the Main Cabinet........................................11

5-2Adjusting the Level Adjusters..............................................................................11

6.LINKING TWO OR MORE MACHINES..................................................12

6-1Setting the Link Switches....................................................................................13

7ADJUSTMENTS......................................................................................14

7-1Turning on the Power..........................................................................................14

7-2Adjustment Switches...........................................................................................14

7-3Test Mode............................................................................................................15

7-3-1Coin Options.........................................................................................16

7-3-2Game Options......................................................................................17

7-3-3I/O Test..................................................................................................19

7-3-4Switch Test............................................................................................20

7-3-5Motor Test.............................................................................................21

7-3-6Lamp Test..............................................................................................21

7-3-8Monitor Test...........................................................................................22

7-3-7Sound Test............................................................................................22

7-4Adjustments When Replacing Parts (Initialization).............................................23

8.MAINTENANCE......................................................................................24

8-1Replacing the Fluorescent Lamp........................................................................24

8-2.AB Pedal Assembly.............................................................................................25

8-2-1.Removing the AB Pedal Assembly.......................................................25

8-2-2Replacing the Control Pots...................................................................25

8-3.Shift Assembly Maintenance...............................................................................26

8-4Steering assembly Maintenance.........................................................................26

8-4-1Replacing the Control Pot.....................................................................27

8-4-2Replacing the Drive Belt or Steering Motor..........................................27

9.PARTS.....................................................................................................28

10SHEMATIC..............................................................................................34

Page 5

1. SPECIFICATIONS

POWER SUPPLY :- 230volts AC

MONITOR :- Hantarex 28" Polo Colour Monitor with auto degauss.

COIN ACCEPTOR:- Mars CashFlow - 4 Channel

DIMENSIONS :-

Assembled 1396(w) x 1700(d) x 1870(h)

Monitor Cabinet 1396(w) x 760(d) x 1870(h)

Seat Assembly 470(w) x 940(d) x 1230(h)

WEIGHT :-

Assembled 310kg

Monitor Cabinet 250kg

Seat Assembly 30kg

ACCESSORIES :- Keys: (Cash Door) .....................2

(Coin Door) ......................2

(Back Door) .....................2ea

IEC Mains Lead .....................................1

Operators Manual ..................................1

Monitor Manual ......................................1

Cashflow Manual ...................................1

Link Cable .........................................1

Seat/Cabinet Joint Bracket ....................4

M10x35 Hex Head Set Screw................24

M10 Spring Washer ...............................24

M10 Flat Washer....................................24

M5 Security Wrench ..............................1

Page 6

2. PRECAUTIONS

2-1 Cautions when Transporting.

a. Do not subject the game to physical shock when transporting or moving it.

b. Always return the levellers to the UP position before moving the machine.

c. Take care not to rope any moulded (plastic) parts when transporting.

d. Always separate the seat assemblies from the cabinet before moving or

transporting the machine.

e. The main cabinet has a high centre of gravity, take care that the machine is

balanced if using a fork lift.

2-2 Cautions when Handling.

a. AC power must always be turned OFF, and the game disconnected, before

replacing any parts or connecting/disconnecting connectors.

b. When unplugging the game from an electrical outlet, always grasp the plug, not

the mains lead.

c. The machine must be earthed with a securely connected earthed plug.

d. Care must be taken at all times to avoid electric shock when inspecting or

adjusting the game.

2-3 Cautions when Operating

a. Only parts specified by Namco Ltd. should be used when replacement is

necessary.

b. Only operate the machine after checking that has been installed in accordance

with the installation details (See 2-4 "Cautions when Installing")

c. Adjustment is required whenever the game PCB board, ROM, Steering Assy,

Accelerator/Brake Assy or Controls are replaced. (See 7-4 "Adjusting the Game

After Replacing Parts" on page 19)

d. Always turn power OFF before performing any maintenance or adjustments.

e. The Switch Mode Power Supply and Monitor Chassis may still be hot and retain

high voltage after the power has been turned OFF, take care not to touch these

areas.

f. Before performing any work not described in this manual, contact your dealer for

instructions.

Page 7

2-4 Cautions when Installing

This machine is designed for indoor use only. The game must not be installed outdoors

or under the following conditions:-

a. In areas directly exposed to sunlight, high humidity, direct water contact, dust, high

heat or extreme cold.

b. In locations that would present an obstacle in the case of an emergency, ie. near fire

equipment or emergency exits.

c. On an unstable or uneven surface, or subject to floor vibration.

d. To allow sufficient access, ensure that there is at least 300mm each side between

other machines or walls and 500mm at the rear.

(Note: If the other machine is another Victory Lap there is no need to leave a gap

between machines.)

Page 8

3. HOW TO PLAY

• This machine is a multi-player racing game that allows several people to play at

the same time, up to a maximum number of eight.

• When two or three players are competing against each other, a computer car is

included and competition is between four cars.

When only one player is playing, he/she competes against the computer cars.

When four or more players compete against each other, competition is amongst

those players only.

• In the case of linked play, the "Championship Point Mode" functions and players

are able to carry over their individual race points for up to three games.

[Game Summary]

• The object of the game is to complete the set number of laps as fast as possible

within the set time.

• The game is over after completing the set number of laps. The finishing position,

lap time, and total time are displayed at the end of the game.

• If the set time runs out (becomes "0") before the laps are completed, the game is

over.

[Championship Point Mode]

• At the end of a game, the race ranking, total points acquired and points ranking

are displayed.

The participating players are awarded points according to the final position for

each race. Also, points are awarded during the race to the lap leader (player

leading at the start of each lap). In this way, points are accumulated every race.

• After the first or second game, only those players that continue are included in

the points accumulation.

The shift type and the race class for the next race are the same as the previous

race, however the course is selected automatically.

If only one player continues, no points are awarded.

• At the end of the third race, the final accumulated points ranking is displayed and

the game is over.

[Starting the Game]

• Insert a coin/s. Move the shift lever up or down to select the course.

SEROW VALLEY (High speed course), STREAM FIELD (semi-technical course),

CAPITAL CITY CIRCUIT (Technical course). Then depress the accelerator

• Next, move the shift lever up or down to select the level of difficulty (beginner,

expert, expert (pro)) and then depress the accelerator.

• Finally, move the shift lever up or down to select the method of gear shifting,

AT (auto) or MT (manual) and then depress the accelerator.

Page 9

• After making selections, wait for the empty seat entry.

• A linked game starts when all of the connected seats have been entered, or

twenty seconds after the first coin/s have been inserted.

If there is no entry by another person within the twenty seconds, the game starts

as a single player.

• A single player game can be started without waiting for other players by inserting

a coin/s while pressing the view change button.

Page 10

4. MAJOR COMPONENTS

Page 11

5. INSTALLATION

5-1 Connecting the Seat Assemblies to the Main Cabinet

a. Place the main cabinet in its final position.

b. Connect the connectors between the Seat Assembly and Main Cabinet.

c. Fix the Seat Assemblies to the Cabinet using the Joint Plates, M10 hex head

screws, flat washers and spring washers taking care not to trap any wires

between the Seat Assembly and Cabinet.

5-2 Adjusting the Level Adjusters

When the seats have been assembled to the main cabinet, lower the level adjusters,

(4 on the main cabinet and 4 on each seat assembly), with a spanner so that all

castors are raised from the floor and the machine is level.

Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Page 12

6. LINKING TWO OR MORE MACHINES

Up to four machines (8 seats) can be linked together.

The machines should be linked as described below.

NOTE: Each machine can draw up to 3 amps. Make sure that the power supply

is adequate.

a. Ensure that the power is "OFF".

b. Loosen the two screws (M4x10) on the back of the main cabinet, and remove the

connector cover.

c. Set the link switches to "ON" , "EXT", and

"ON". (See Diag.)

d. Use the supplied link cable and connect

the machines between "IN" and "OUT"

sockets (See Diag.)

[Examples of Linked Machines]

a) 2 Machines

(4 Seats)

b) 3 Machines

(6 Seats)

c) 4 Machines

(8 Seats)

Page 13

e. Turn the power to each machine "ON", and set the PCB ID using the test mode.

(Refer to section 7-3-2 "Setting the Game Options" (page17))

Note: Settings other than those described will cause the machine to operate

incorrectly.

6-1 Setting the Link Switches

The link switches are used to set the connection between seats and machines.

a. Setting only one machine (2 seats)

Set the link switches to "ON", "INT", and "ON".

Note: Do not use a link cable.

b. Setting two or more machines.

Set the link switches to "ON", "EXT", and "ON".

c. Install the connector cover using the

two screws (M4x10).

The link procedure is now complete.

d. Setting for faulty PCB.

If the game PCB of only one side is faulty, set the link on that side to "OFF"

[Example of setting for faulty left side]

Page 14

7 ADJUSTMENTS

7-1 Turning on the Power

After the machine has been installed, turn ON the power. The Power switch is

located on the rear of the Main cabinet. (See section 4 "Major Components"

(page 10).)

7-2 Adjustment Switches

The adjustment switches are located inside the coin door.

1. Service Switch

Press this switch to obtain game credits without incrementing the play meters.

2. Test Switch

Slide this switch "ON" to enter test mode.

Test mode allows game testing and the changing of game settings. (Refer to

section 7-3 "Test Mode" (page 15).)

Service Bracket

Page 15

7-3 Test Mode

1. Open the coin door and slide the test switch "ON". The "Menu Screen" will be

displayed on the monitor.

2. Select the test required by moving the shift lever up or down. The colour of

the selected test will change.

3. Enter the selected test by stepping on the accelerator. Select "EXIT" to return

to the "Menu Screen" (step on the accelerator when using the monitor test

screen).

4. After testing is completed, ensure that the test switch is returned to the "OFF"

position to return to game mode.

The Test Switch must always be in the "OFF" position for normal game mode.

COIN OPTIONS------(1)Sets the price of play. (See 7-3-1)

GAME OPTIONS------(2)Sets the game options. (See 7-3-2)

I/O TEST ------ (3) Used for testing the switches and motor.

(See 7-3-3)

MONITOR TEST------(4)Used for adjusting the monitor. (See 7-3-8)

SOUND TEST ------ (5) Used for adjusting the speaker volume.

(See 7-3-7)

ADS DATA ------ (6) Displays the accumulated game data.

OTHERS ------ (7) Used for testing the PC boards and for

initializing all of the settings.

GAS: ENTER SHIFT: CHOOSE

Page 16

7-3-1 Coin Options

a. Select item (1)

"COIN OPTIONS"

on the menu screen,

to set the game cost

and related settings.

b. Use the shift lever to

select the required

item then step on

the accelerator.

c. Use the shift lever to

change the settings

then step on the

accelerator to store

the new values.

d. Select "EXIT" to

return to the menu

screen.

ITEM CONTENTS FACTORY SET

(a) Game Cost Coins required for 1 credit - - - - - - settable 1 - 9 1

(b) Coin 1 Mech Value Number of pulses on meter per coin - - - - - - settable 1 - 9 1

(d) Bonus Coin Extra coin pulse at specified coins in NONE

(e) Free Play Game started by pressing accelerator - - - - - - Yes/No NO

COIN OPTIONS [DEFAULT IN GREEN]

GAME COST

1 COIN 1 CREDIT ........... (a)

COIN1 MECH VALUE

1 COIN COUNT AS 1 COIN ........... (b)

COIN MECH 2 VALUE

1 COIN COUNT AS 1 COIN ........... (c)

BONUS FOR QUANTITY BUY IN

NONE ........... (d)

FREE PLAY

OFF ........... (e)

EXIT

GAS: ENTER SHIFT: CHOOSE

Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that

the Coin Options on the screen are set as shown in the following table.

Page 17

7-3-2 Game Options

a. Select item (2) "GAME

OPTIONS" on the

menu screen to set the

game options.

b. Use the shift lever to

select the required item

then step on the

accelerator.

c. Use the shift lever to

change the settings

then step on the

accelerator to store the

new values.

d. Select "EXIT" to return

to the menu screen.

NOTES

•The rank (level of difficulty) and number of laps must be set the same

on all positions that are linked.

•The PCB number of the seat furthest left (when facing the front of the

machine) should be set to 1, and the other seats set to 2, 3, 4 and so

on in order from left to right. The PCB number of the farthest right

position should equal the number of positions linked.

•Settings other than those described will cause the machine to operate

incorrectly.

(See page 14 for descriptions)

GAME OPTIONS [DEFAULT IN GREEN]

PCB ID NUMBER 1 ................. (a)

TEAM COLOUR BLUE 3 ................. (b)

COURSE SEROW VALLEY............. (c)

RACE CLASS BEG EXP PRO.......... (d)

SOLO DIFFICULTY B B B ............... (e)

SOLO RACE LAPS 3 3 3 ............... (f)

LINK DIFFICULTY B B B ............... (g)

LINK RACE LAPS 3 3 3 ............... (h)

SPEED DISPLAY KM/H ................. (i)

SOUND IN ATTRACT ON ................. (j)

EXIT

GAS: ENTER SHIFT: CHOOSE

Page 18

ITEM DESCRIPTION FACTORY SET

(a) PCB Number The PCB number should be set so that none of the linked positions have the same number

(b) Team Colour RED 25 or 26

BLUE 3 or 4

YELLOW 17 or 18

GREEN 11 or 12

* When more than three sets (6 seats) are linked, different race numbers should be used for

the same team colours.

(f) Number of laps (Solo game) 2 to 6 3