NCR 7409-K223 Manual

7409-K223/K225
MSR
Kit Instructions
Issue D

Revision Record
Issue Date Remarks
A Jan 2009 First issue
B Mar 2009 Kit PID changed to accommodate new 19”
terminal; was 7409-K221 (longer ground cable)
C Dec 2009 Added JIS model
D July 2011 Added 7409-K225; was 7409-K224

1
Introduction
This kit provides an MSR module that mounts on the side of the 7409 Display Head.
There are two versions:
JIS MSR (7409-K223)
ISO MSR (7409-K225)
26439

2
Installation Procedures
Warning: Disconnect the AC power cord before disassembling the Terminal.
1. Remove the Display Head from its mount.
Removing the 7409 from the Table Top Mount
a. Release the Mounting Plate Latches and tilt the display back. Relock the
latches.
26901
Mounting Plate Latches

3
b. Loosen the captive screw that secures the Cable Cover and remove the cover.
26690
Cable Cover Captive Screw
c. Disconnect the cables from the I/O Panel.
26445a
Terminal Power Cable
Printer USB Cable
Keyboard USB Cable

4
d. Release the Mounting Plate Latches and remove the 7409 from the mount.
26659
Mounting Plate Latches
Baseplate
Removing the 7409 from the Fixed Angle Mount
a. Remove the screws (2) in the sides of the Fixed Angle Mount.
26681
Screw
(One on each side)

5
b. Rest the bottom of the display on the Display Support.
26680
Display Support
Cable Cover Captive Screw
Note: Place the Display Support behind the extension on then Display Hinge
Bracket.
24753
Display Support
Bracket Extension
c. Loosen the captive screw that secures the Cable Cover and remove the cover.

6
d. Disconnect the cables from the I/O Panel.
Note: The Power Cable connector locks into position when connected to the
terminal and cannot be removed by simply pulling on the cable. You must
grasp the connector and slide the outside housing out from the terminal to
unlock it from the terminal connector.
26445
Terminal Power Cable
Printer USB Cable
Keyboard USB Cable
e. Slide the Locking Brackets (2) to the unlocked position.
24747

7
f. Remove the display from the Fixed Angle Mount.
24629
g. Disconnect the Power Cord from the I/O Panel on the terminal.
2. Lay the terminal face down on a flat surface.
3. Loosen the captive screws (2) that secure the Rear Cover.
26903
Captive Screws
Rear Cover

8
4. Pivot the Rear Cover to the open position.
26651a
Rear Cover Latches
5. Remove the Rear cover by squeezing the Rear Cover Latches together as indicated
above.

9
6. Remove the No MSR Cover (2 screws).
26902
No MSR Cover
7. Insert the cables into the opening in the chassis and install the MSR Assembly in
the slots of the cabinet.
26692
MSR
8. Secure the MSR to the chassis (2 screws).

10
9. Connect the MSR USB Cable to the I/O Board.
10. Connect the MSR Ground Cable to the chassis (screw).
26691
MSR Data Cable
MSR Ground Cable
11. Replace the Rear Cover and mount the Display Head to its mount using the
reverse procedures.

11
MSR Programming
If the MSR Module (ISO) is replaced the customer is responsible for re-programming
the device to custom wedge-emulation parameters, using the NCR MSR
Configuration Utility, which is available on the NCR website at:
http://www.ncr.com
1. At this site, select the Support tab.
2. Select Drivers and Patches →Retail Support Files →NCR RealPOS and
SelfServ Terminal and Operating Systems →NCR RealPOS 25 (7610) →
Windows →[Operating System].
3. Select the MSR Configuration Utility.
For information about how to use the utility see the NCR MSR Configuration Utility
User Guide (B005-0000-2031).