NEC NC1100CM User manual

12016-02-10 #:126-9107-2 2016-04-15
ENG
Projector Mount
NC1100CM
150 lb
(68 kg)
MAX
CONFIGURATION NC900C NC1100L PX750U
PROJECTORS NC900C NC1100L, NC1201L,
PH1202HL,
PH1202HL1,PH1201QL
PX602WL, PX602UL,
PX700W, PX750U,
PX800X, PX700W2,
PX750U2, PX800X2,
PX803UL

22016-02-10 #:126-9107-2 2016-04-15
Before installing make sure the supporting truss will support the combined load of the equipment and hardware.
Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never
exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and
position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to
product failure or personal injury. For support please call customer care at 1-800-865-2112.
WARNING
Symbols
WARNING x3
Screws must get
at least three full
turns and fit snug.
Tools Needed for Assembly.
Do not over tighten screws
WARNING
To properly tighten screws: Tighten until screw head
makes contact, then tighten another 1/2 turn. Do not
overtighten screws.
7/16"
Parts List Part #Description Qty
Aextension bracket 1 056-1369
Bhook-on bracket 1 056-1370
Cadapter bracket 2 056-1364
Dcollar 1 1800-375
Ehandle bracket 2 056-1365
Fhandle bar 2 056-1371
Ghandle tab 2 056-1366
HM6 x 16mm socket pin screw 6 520-1132
Iknob 8 560-0252
J1/4" flat washer 16 540-9440
K.26ID x .7OD x .062 nylon washer 14 540-9439
L1/4-20 socket screw 2 520-1013
M1/4-20 hex nut 2 530-9413
NM5 x 10mm type F screw 7 520-9250
O1/4-20 x 1/4" set screw 4 500-1084
P5/32" (4mm) security wrench 1 560-9646
QM4 x 16mm socket pin screw 6 510-1087
RM4 x 12mm socket pin screw 6 510-1079
Scable assembly 1 130-8012
T2.125" fiber washer 1 540-9432
UM6 x 12mm socket pin screw 6 520-1050
Vcable tie (not shown) 4 560-9711
B (1)
hook on
bracket
C (2)
adapter bracket
A (1)
extension
bracket

32016-02-10 #:126-9107-2 2016-04-15
D (1)
collar
E (2)
handle bracket
F (2)
handle bar
G (2)
handle tab I (8)
knob
J (16)
1/4" flat washer
K (14)
nylon washer
O (4)
set screw
P (1)
wrench S (1)
cable
assembly
T (1)
washer
H (6)
M6 x 16mm L (2)
1-4x20 x 3/4"
M (2)
1/4-20 hex nut
Q (6)
M4 x 16mm R (6) M4 x 12mm U (6) M6 x 12mm
N (7)
M5 x 10mm

42016-02-10 #:126-9107-2 2016-04-15
Assemble as shown. Locate projector below and follow
proper configuration.
I (4)
L (2)
J (4)
K (4)
K (6)
J (2)
M (2)
CONFIGURATION NC900C NC1100L PX750U
PROJECTORS NC900C NC1100L, NC1201L,
PH1202HL,
PH1202HL1,PH1201QL
PX602WL, PX602UL, PX700W,
PX750U, PX800X, PX700W2,
PX750U2, PX800X2, PX803UL
1

52016-02-10 #:126-9107-2 2016-04-15
Thread collar (D) onto the extension column. Align the notch inside the
extension column with one of the threaded holes in the collar as shown.
Secure using an M5x 10mm type-F screw (N). hardware as shown.
Secure set screws to prevent excess movement.
A
D
N
D
2
3
O (4)

62016-02-10 #:126-9107-2 2016-04-15
Attach assembly to projector as shown. Note the orientation for each specific projector.
H or U (6)
H or U(6)
S (4)
J (6)
J (6)
R or Q (4)
PH1000U Configuration
NC900C Configuration
NC1100L Configuration
x3
x3
x3
center screw
not required
4

72016-02-10 #:126-9107-2 2016-04-15
E
F
PX750U Configuration
NC900C Configuration
NC1100L Configuration
N (4)
5
6

82016-02-10 #:126-9107-2 2016-04-15
Position second handle bar in the relief cut in the handle
brackets at the opposite end of the assembly. Secure using
the handle tabs with M5 x 10 mm type-F screws (N).
N
G
F
7 a
a
a
a

92016-02-10 #:126-9107-2 2016-04-15
Hook the assembly to the ceiling mount assembly as shown. Use handle bars (F) to lift projector.
Attach cable assembly.
S
I(4)
J(4)
K(4)
U-BOLT
CLAMP
S
8-1
8-2

10 2016-02-10 #:126-9107-2 2016-04-15
Adjust tilt and roll by loosening the knobs, setting
the position, then retightening the knobs.
Loosen
Adjust
Tighten
Loosen
Adjust
Tighten
generic projector generic projector
9