Necta Rondo Owner's manual

PROGRAMMING MANUAL
Code: Date:P2125EN00
English
01 - 2008
Rondò

P2125EN00 01 - 2008
In t r o d u c t I o n
This “Programming Manual” is a very useful tool for those operators who want to get the most out of the poten-
tial of the installed software and know in detail all of the available software functions.
This document is available in PDF format in the Reserved Area of our internet site
www.nwglobalvending.com or, on request, through our after-sales service.
The Manual is divided into 3 parts:
The First Part regards Normal Vending Mode; it describes the operations to be carried out during the vending
machine normal use:
- Power-on
- Messages for the user.
The Second Part descries the Filler Menu, the programming part that is used for changing individually the
sales prices of the selections and for simple controls on the functioning and on the machine sales.
The Third Part describes the Technician Menu, the programming part that is meant for technical personnel,
used for changing the machine performance.
The operations described can modify the functioning cycles, therefore they must be carried out only by per-
sonnel who have the specic knowledge of the machine functioning from a point of view of electrical safety
and health regulations.
The appendix contains the List of Failures, which describes the possible error signals and the self-diagnosis
conditions of the machine; it also describes the functions concerning the coin mechanism communication
protocols.
no r m a l v e n d I n g m o d e
Po w e r -o n
When closing the payment system compartment door or energising the machine, the power-on process is
started and the display indicates the version number of the installed software.
The machine can be programmed for displaying, for a few second, the number of selections made.
After a few seconds the internal lighting lamp is switched on and the machine goes into normal operating
mode:
A

P2125EN00 01 - 2008
B
me s s a g e s f o r t h e u s e r
The following table indicates the most common strings that may be shown on the machine display in normal
vending mode.
String Description
SELECT THE PRODUCT The machine waits for the user to make a product selection by
pressing the relevant selection button.
NO CHANGE The machine signals that, in the event the money in the tubes is
lower than the required minimum, the change is not guaranteed.
WAiT PLEASE The machine is dispensing the selected product.
TAKE THE PRODUCT The machine has completed the dispensing of the selected
product.
DiSPENSiNG fAiLED The machine signals that there was a failure or malfunction that
did not permit the correct dispensing of the product.
VENDiNG MACHiNE OUT Of ORDER It is not possible to make selections. Besides this message, the
failure that caused this condition is displayed alternating.
SUSPENDED SERViCE
It is not possible to make selections. This condition occurs when
the machine is in Energy Saving mode or while dispensing a prod-
uct from the slave machine.
NOT DiSPENSED
The machine signals that it is not possible to dispense the product
being selected because presumably the product is nished or
there is a motor failure.
SELECTiON DiSAbLED It is not possible to make the selection chosen, as such selection
was disabled in the programming menus.
CAUTiON! DiSPENSiNG COMPARTMENT CLOSiNG The machine signal also with a sound warning that the dispensing
compartment locking device is operating.

P2125EN00 01 - 2008
Pr o g r a m m I n g m e n u
In order to access the programming menu rotate the key in the lock (1) to open the metal door, rotate the inter-
nal handle clockwise to open the sliding compartment of the vending machine (2) pulling it outwards, switch on
the machine by inserting the yellow key supplied in the relevant slot (3) shown in the gure.
Press the programming access button as shown in the gure:
The machine goes into “Filler Menu” mode.
The buttons shown in the gure are used for surng through the dierent menus:
Scrolling buttons UP “” and DOWN “”
The UP and DOWN scrolling buttons are used for moving from one programming menu item to the next one,
located in the same level, and at the same time change the status or the numeric value of the corresponding
functions.
”
The conrm / enter key is used for moving to the lower level or for conrming a value after being entered or
changed.
”
The exit key is used for returning to the higher level or for exiting a change eld of a function. When reaching
the highest level in the menu, this button is pressed for going from the Technician menu into the Filler menu
and vice versa.
C

P2125EN00 01 - 2008

1
1 - STATiSTiCS
1.1 - STATiST.PRiNTiNG
1.1.1 - PARTiAL PRiNTiNG
1.1.1.1 - SELECT. COUNT.
1.1.1.2 - bAND COUNTER
1.1.1.3 - fAiLURE COUNT.
1.1.1.4 - COiN MECH.DATA
1.1.1.5 - PRiNT PHOT. ERR.
1
st a t I s t I c s
1.1
Pr I n t I n g t h e st a t I s t I c s
1.1.1
Pa r t I a l P r I n t o u t
1.1.1.1
Pr I n t I n g t h e s e l e c t I o n c o u n t e r s
When conrming this function, the counters regarding the dierent
selections are printed.
1.1.1.2
Pr I n t I n g t h e t I m e b a n d c o u n t e r s
When conrming this function, the counters regarding the dierent
time bands are printed.
1.1.1.3
Pr I n t I n g t h e f a I l u r e c o u n t e r s
When conrming this function, the counters regarding the dierent
failure are printed.
1.1.1.4
Pr I n t I n g t h e c o I n m e c h a n I s m d a t a
When conrming this function, the counters regarding the coin
mechanism data are printed.
1.1.1.5
Pr I n t I n g t h e P h o t o c e l l e r r o r s
When conrming this function, the counters regarding the photocell
errors are printed.
1.1.1.6 - PRiNT MOTOR ERR.
1.1.1.6
Pr I n t I n g t h e m o t o r e r r o r s
When conrming this function, the counters regarding the motor
errors are printed.
1.1.2
t
o t a l P r I n t o u t
When conrming this function, all statistics are printed.
1.1.2 - TOTAL PRiNTiNG

P2125EN00 01 - 2008

2
1.2 - PRiNT REL.STATS.
1.2.1 - PARTiAL PRiNTiNG
1.2.1.1 - SELECT. COUNT.
1.2.1.2 - bAND COUNTER
1.2.1.3 - fAiLURE COUNT.
1.2.1.4 - COiN MECH.DATA
1.2.1.5 - PRiNT PHOT. ERR.
1.2
Pr I n t I n g t h e r e l a t I v e s t a t I s t I c s
1.2.1
Pa r t I a l P r I n t o u t
1.2.1.1
Pr I n t I n g t h e s e l e c t I o n c o u n t e r s
When conrming this function, the relative counters regarding the
dierent selections are printed.
1.2.1.2
Pr I n t I n g t h e t I m e b a n d c o u n t e r s
When conrming this function, the relative counters regarding the
dierent time bands are printed.
1.2.1.3
Pr I n t I n g t h e f a I l u r e c o u n t e r s
When conrming this function, the relative counters regarding fail-
ures are printed.
1.2.1.4
Pr I n t I n g t h e c o I n m e c h a n I s m d a t a
When conrming this function, the relative counters regarding the
coin mechanism data are printed.
1.2.1.5
Pr I n t I n g t h e P h o t o c e l l e r r o r s
When conrming this function, the relative counters regarding the
photocell errors are printed.
1.2.1.6 - PRiNT MOTOR ERR.
1.2.1.6
Pr I n t I n g t h e m o t o r e r r o r s
When conrming this function, the counters regarding the motor
errors are printed.
1.2.2
t
o t a l P r I n t o u t
When conrming this function, all relative statistics are printed.
1.2.2 - TOTAL PRiNTiNG

P2125EN00 01 - 2008

3
1.3 - STATiST. DiSPLAY
1.3.1 - SEL.COUNT.DiSPL.
1.3.1.1 - COUNT X S. SEL.
1.3.1.2 - TOT.COUNT DiSPL.
1.3.2 - DiSP.bAND COUNT.
1.3.3 - fAiLURE COUNT.
1.3.4 - COiN MECH.DiSPL.
1.3.4.1 - AUDiT DATA DiSP.
1.3
dI s P l a y I n g t h e s t a t I s t I c s
1.3.1
dI s P l a y I n g t h e s e l e c t I o n c o u n t e r s
1.3.1.1
dI s P l a y I n g t h e s I n g l e c o u n t e r s
This function is used for displaying the counters regarding each
selection, divided by price band (0, 1, 2, 3, 4, Free, Test).
1.3.1.2
dI s P l a y I n g t h e t o t a l c o u n t e r s
This function is used for displaying the total counters regarding each
selection.
1.3.2
dI s P l a y I n g t h e t I m e b a n d c o u n t e r s
When selecting the desired price band (0, 1, 2, 3, 4, Free, Test), the
total number of selections made for that price band is displayed.
1.3.3
dI s P l a y I n g t h e f a I l u r e c o u n t e r s
This function is used for displaying the number of times each pos-
sible failure occurred in the vending machine.
1.3.4
dI s P l a y I n g t h e c o I n m e c h a n I s m d a t a
1.3.4.1
dI s P l a y I n g t h e a u d I t d a t a
This function is used for displaying the number of coins inserted in
the vending machine, dierentiated by the type of coin.
1.3.4.2 - CASH COUNT.DiSP.
1.3.4.2
dI s P l a y I n g t h e c a s h e d a m o u n t
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit

P2125EN00 01 - 2008

4
1.3.5
dI s P l a y I n g t h e P h o t o c e l l e r r o r c o u n t e r s
This function is used for displaying the value of the counter regard-
ing the photocell errors.
1.3.6
dI s P l a y I n g t h e m o t o r e r r o r c o u n t e r s
This function is used for displaying the value of the counter regard-
ing the motor errors.
1.4
dI s P l a y I n g t h e r e l a t I v e s t a t I s t I c s
1.4.1
dI s P l a y I n g t h e s e l e c t I o n c o u n t e r s
1.4.1.1
dI s P l a y I n g t h e s I n g l e c o u n t e r s
This function is used for displaying the counters regarding each
selection, divided by price band (0, 1, 2, 3, 4, Free, Test).
1.4.1.2
dI s P l a y I n g t h e t o t a l c o u n t e r s
This function is used for displaying the total counters regarding each
selection.
1.4.2
dI s P l a y I n g t h e t I m e b a n d c o u n t e r s
When selecting the desired price band (0, 1, 2, 3, 4, Free, Test), the
total number of selections made for that price band is displayed.
1.4.3
dI s P l a y I n g t h e f a I l u r e c o u n t e r s
This function is used for displaying the number of times each failure
occurred in the vending machine.
1.3.5 - PHOT.ERR.COUNTER
1.3.6 - MOT.ERR.COUNTER
1.4 - DiSP.REL.STATS.
1.4.1 - SEL.COUNT.DiSPL.
1.4.1.1 - COUNT X S. SEL.
1.4.1.2 - TOT.COUNT DiSPL.
1.4.2 - DiSP.bAND COUNT.
1.4.3 - fAiLURE COUNT.

P2125EN00 01 - 2008

5
1.4.4 - COiN MECH.DiSPL.
1.4.4.1 - AUDiT DATA DiSP.
1.4.4.2 - CASH COUNT.DiSP.
1.4.5 - PHOT.ERR.COUNTER
1.4.6 - MOT.ERR.COUNTER
1.4.4
dI s P l a y I n g t h e c o I n m e c h a n I s m d a t a
1.4.4.1
dI s P l a y I n g t h e a u d I t d a t a
This function is used for displaying the number of coins inserted in
the vending machine, dierentiated by the type of coin.
1.4.4.2
dI s P l a y I n g t h e c a s h e d a m o u n t
This function is used for displaying the value of:
- Total cashed
- Total sold
- Total cashed by credit
1.4.5
dI s P l a y I n g t h e P h o t o c e l l e r r o r c o u n t e r s
This function is used for displaying the value of the counter regard-
ing the photocell errors.
1.4.6
dI s P l a y I n g t h e m o t o r e r r o r c o u n t e r s
This function is used for displaying the value of the counter regard-
ing the motor errors.

P2125EN00 01 - 2008

6
1.5
de l e t I n g t h e r e l a t I v e s t a t I s t I c s
1.5.1
Pa r t I a l d e l e t e
1.5.1.1
de l e t I n g t h e s e l e c t I o n c o u n t e r s
When conrming this function, the counters regarding the dierent
selections are deleted.
1.5.1.2
de l e t I n g t h e f a I l u r e c o u n t e r s
When conrming this function, the counters regarding the dierent
failure are deleted.
1.5.1.3
de l e t I n g t h e c o I n m e c h a n I s m d a t a
When conrming this function, the counters regarding the coin
mechanism data are deleted.
1.5.1.4
de l e t I n g t h e P h o t o c e l l e r r o r c o u n t e r s
When conrming this function, the counters regarding the photocell
errors are deleted.
1.5.1.5
de l e t I n g t h e m o t o r e r r o r c o u n t e r s
When conrming this function, the counters regarding the motor
errors are deleted.
1.5.2
t
o t a l d e l e t e
When conrming this function, all relative statistics are deleted.
1.5 - CANC.RELAT.STATS
1.5.1 - PARTiAL RESET
1.5.1.1 - SELE. COUNT RESET
1.5.1.2 - fAiLURE COUNT.
1.5.1.3 - COiN MECH DATA
1.5.1.4 - CANC. PHOT. ERR.
1.5.1.5 - CANC.MOT.ERR.CNT
1.5.2 - TOTAL RESET

P2125EN00 01 - 2008

7
2 - iNDiViDUAL PRiCE
2.1 - PRiCE bAND 0
2.2 - PRiCE bAND 1
2.3 - PRiCE bAND 2
2.4 - PRiCE bAND 3
2.5 - PRiCE bAND 4
2
sI n g l e P r I c e s
2.1
Pr I c e b a n d 0
This function is used for setting a dierent price for each selection in
time band 0.
2.2
Pr I c e b a n d 1
This function is used for setting a dierent price for each selection in
time band 1.
2.3
Pr I c e b a n d 2
This function is used for setting a dierent price for each selection in
time band 2.
2.4
Pr I c e b a n d 3
This function is used for setting a dierent price for each selection in
time band 3.
2.2
Pr I c e b a n d 4
This function is used for setting a dierent price for each selection in
time band 4.
3 - TUbE CONTROL
3.1 - fiLLiNG TUbE
3.2 - TUbE EMPTYiNG
3
ch a n g e t u b e s c o n t r o l
3.1
fI l l I n g t h e c h a n g e t u b e s
From this function, the change tubes can be lled manually.
Conrming the relling, the display will indicate
“Credit: ——” which is the value of money available in change the
tubes; insert the desired coin into the validator and the display will
indicate the value of money available in the change tubes.
3.2
re l e a s I n g t h e c h a n g e t u b e s
From this function, the change tubes can be released manually.
When conrming the releasing, it will be possible to decide which
tube to release. Each time the conrm button is pressed, a coin is
ejected from the active tube.

P2125EN00 01 - 2008

8
4 - SPECiAL SELECT.
4.1 - ViRTUAL SELECT.
4.2. - ViRT. PRiCE RET.
4
sP e c I a l s e l e c t I o n s
4.1
vI r t u a l s e l e c t I o n s
This function is used to dene a pair of selections that can be sold
at a price dierent from the sum of the two selections, using a single
selection number. 10 virtual selections can be programmed (70 to
79).
4.2
re t u r n o f v I r t u a l P r I c e
This function is used to dene, in the event of failed second dis-
pensing in a virtual selection, not to cash the price of the second se-
lection (only if an MDB payment system or validator are used). With
other payment systems, it can be decided whether or not return the
entire amount.
4.3 - TWO-MOTOR SELECT
4.4 - PHOTOCELL PARAM.
4.3
tw o -m o t o r s e l e c t I o n s
With this function the operation of two motors for dispensing long
shaped products can be combined, specifying the selection number
of the second motor.
The rst motor number will be the selection number, while the selec-
tion number of the associated motor will remain disabled.
4.4
Ph o t o c e l l P a r a m e t e r s
The vending machine can be tted (as standard feature or as op-
tional according to the model) with a device that detects the pas-
sage of dispensed products.
4.4.1 - SETTLiNG TiME
4.4.2 - MONEY RETURN
4.4.3 - EMPTY SEL.CONTR.
4.4.1
se t t l I n g t I m e
This function is used for setting an additional rotation time to the
spiral beyond the limit switch to allow the selected product to fall in
the dispensing compartment.
re t u r n o f m o n e y
This function is used for enabling the return of the amount paid in
the event the photocells do not detect the passage of the selected
product.
4.4.3
em P t y s e l e c t I o n c o n t r o l
This function is used for disabling the selection that recorded a pho-
tocell error, i.e. failed product dispensing/detection.

P2125EN00 01 - 2008

9
5 - TEST
5
t
e s t
5.1
te s t s e l e c t I o n
This function is used to simulate the normal dispensing of products
without inserting any money to check the functioning of the spiral
rotation by pressing the selection buttons.
5.1 - TEST SELECTiON
5.2 - MOTOR TEST
5.3 - AUTOTEST
5.2
mo t o r t e s t
This function is used for actuating all motors in a sequence, indicat-
ing on the display the number of the involved selection.
5.3
au t o t e s t
This function allows testing, in a semiautomatic way, of the main ma-
chine components. When pressing the conrm button, the message
“AUTOTEST” will be start blinking.
It is possible to cancel each operation and go to the next one by
pressing the exit button, but conrming with the conrm button to
start the autotest routine. Some checks occur automatically, others
need the manual operation of the monitored component.
In a sequence:
- Push-button panel test; the machine will display the number of the
button which must be pressed and awaits the actuation before going
to the next button.
- Temperature test; the machine will display the value of temperature
detected by the probe. In the event of interruption the value -11.0 is
displayed; in the event of short-circuit the value 41.0 is displayed.
- Buzzer test; the machine will emit a series of test sounds.
- Compressor test; the compressor is activated/deactivated using
the “” and “” buttons.
- Selection test; the machine will simulate the dispensing of each
selection in a sequence.
- Coin mechanism test; the machine checks that communication
with the coin mechanism takes place correctly and which validator
lines are set as being active.
- Photocell test; in the event where the machine is equipped with a
device for detecting the passage of products the light beam reading
and interruption are checked.
- Dispensing compartment lock test; in the event where the machine
is equipped with a device for locking the dispensing compartment,
the “” and “” buttons are used for locking and unlocking the
compartment opening.
- Direct push-button test; the machine will display the number of the
button which must be pressed and awaits the actuation before going
to the next button.

P2125EN00 01 - 2008

10
6
gsm
6.1
re s e t t I n g t h e P r e -a l a r m c o u n t e r s
With this function the counters that control the pre-alarms are reset.
7
evadts
7.1
co n n e c t I o n
This function places the machine in wait mode for connection to
retrieve data.
6 - GSM
6.1 - RESET PRE-AL.CNT
7 - EVADTS
7.1 - CONNECTiON

P2125EN00 01 - 2008

11
1 - fAiLURES
1.1 - fAiLURE READiNG
1.
fa I l u r e s
1.1
re a d I n g t h e f a I l u r e s
When the “Failure” function is displayed, press the conrm button
“” to display the present failures.
If no failures are currently present, after pressing the conrm button
“” the message “End failures” will be displayed.


1.2
re s e t t I n g t h e f a I l u r e s
By conrming this function all current failures will be reset.
1.2 – fAiLURE RESET
1.3 - MOTOR ERRORS
1.3
mo t o r e r r o r s
With this function the failed motors are displayed for approximately
1 second. In the event the is more than 1 motor errors at the same
time, scrolling between errors is automatic.
1.4 - MOTORS’ STATUS
1.4
mo t o r s ’ s t a t u s
This function is used to read the last failure that occurred in each
spiral, even if the machine conguration has an empty position.
A motor can be in one of the following conditions:
- motor functioning
- motor not present; when the motor is not detected at machine
power-on
- motor disconnected; when a motor detected at machine start-up is
not detected during a selection
- motor blocked; when the positioning button is not operated within
the “timeout”
- empty spiral; when, with the dispensing control (photocells) in-
stalled, no dispensed product is detected.


1.5 - RESET MOTOR ERR.
1.5
re s e t m o t o r e r r o r s
By conrming this function all current failures regarding the motors
will be reset.

P2125EN00 01 - 2008

12
2 - PROGR.PARAMETERS
2.1 - CASH
2.1.1 - PRiCES
2.1.1.1 - iNDiViDUAL PRiCE
2.1.1.1.1 - PRiCE bAND 0
2.1.1.1.2 - PRiCE bAND 1
2
Pr o g r a m m I n g P a r a m e t e r s
2.1
ca s h
This set of functions controls all parameters regarding the payment
systems and the sales prices.
2.1.1
Pr I c e s
Four dierent prices can be set for each selection according to the
programmed time bands for when the time table option is enabled.
For each of the 4 time bands prices (0 to 65,535) can be pro-
grammed globally (same price for all selections) or for the single
selections.
2.1.1.1
se t t I n g s I n g l e P r I c e s
2.1.1.1.1
Pr I c e b a n d 0
th I s f u n c t I o n I s u s e d f o r s e t t I n g ad I f f e r e n t P r I c e f o r e a c h s e l e c t I o n
f o r t I m e b a n d 0.
2.1.1.1.2
Pr I c e b a n d 1
This function is used for setting a dierent price for each selection
for time band 1.
2.1.1.1.3 - PRiCE bAND 2
2.1.1.1.3
Pr I c e b a n d 2
This function is used for setting a dierent price for each selection
for time band 2.
2.1.1.1.4 - PRiCE bAND 3
2.1.1.1.5 - PRiCE bAND 4
2.1.1.1.4
Pr I c e b a n d 3
This function is used for setting a dierent price for each selection
for time band 3.
2.1.1.1.5
Pr I c e b a n d 4
This function is used for setting a dierent price for each selection
for time band 4.

P2125EN00 01 - 2008

13
2.1.1.2 - GLObAL PRiCES
2.1.1.2.1 - PRiCE bAND 0
2.1.1.2.2 - PRiCE bAND 1
2.1.1.2.3 - PRiCE bAND 2
2.1.1.2.4 - PRiCE bAND 3
2.1.1.2
se t t I n g g l o b a l P r I c e s
2.1.1.2.1
Pr I c e b a n d 0
This function is used for setting a single price for all selections avail-
able in time band 0.
2.1.1.2.2
Pr I c e b a n d 1
This function is used for setting a single price for all selections avail-
able in time band 1.
2.1.1.2.3
Pr I c e b a n d 2
This function is used for setting a single price for all selections avail-
able in time band 2.
2.1.1.2.4
Pr I c e b a n d 3
This function is used for setting a single price for all selections avail-
able in time band 3.
2.1.1.2.5 - PRiCE bAND 4
2.1.1.2.5
Pr I c e b a n d 4
This function is used for setting a single price for all selections avail-
able in time band 4.

P2125EN00 01 - 2008

14
2.1.1.3.4 - TiME bAND 3
2.1.1.3.5 - TiME bAND 4
2.1.1.3.4
tI m e ba n d 3
The time bands are programmable for beginning and end time by
hours (00 to 23) and minutes (00 to 59). If the values for start and
end of the time band are set to 00.00 the time period is disabled.
2.1.1.3.5
tI m e ba n d 4
The time bands are programmable for beginning and end time by
hours (00 to 23) and minutes (00 to 59). If the values for start and
end of the time band are set to 00.00 the time period is disabled.
2.1.1.3.3 - TiME bAND 2
2.1.1.3.3
tI m e ba n d 2
The time bands are programmable for beginning and end time by
hours (00 to 23) and minutes (00 to 59). If the values for start and
end of the time band are set to 00.00 the time period is disabled.
2.1.1.3 - TiME bANDS
2.1.1.3.1 - SET DATE & TiME
2.1.1.3
tI m e b a n d s
Four programmable time bands are provided for selling products at
dierent prices.
Time band 0 is not programmable and covers the 24 hours.
2.1.1.3.1
se t da t e a n d tI m e
This function is used for setting the reference time given by an inter-
nal clock programmable for:
day/month/year/week-day 1-7 (1=Monday, 2=Tuesday, etc…) and
then hour/minutes/seconds.
2.1.1.3.2 - TiME bAND 1
2.1.1.3.2
tI m e ba n d 1
The time bands are programmable for beginning and end time by
hours (00 to 23) and minutes (00 to 59). If the values for start and
end of the time band are set to 00.00 the time period is disabled.

P2125EN00 01 - 2008

15
2.1.2 - COiN MECHANiSMS
2.1.2.1 - COiN MECHAN.SET.
2.1.2.2 - CHANGE iMMEDiAT.
2.1.3 - DECiMAL POiNT
2.1.2
co I n m e c h a n I s m s
2.1.2.1
se t t I n g t h e c o I n m e c h a n I s m s
It is possible to decide which of the payment system protocols avail-
able are to be enabled for the functions.
The available payment systems are:
- Executive
- Validators
- BDV
- MDB
-

2.1.2.2
Im m e d I a t e c h a n g e
This function is valid only in the case where a change-giver coin
mechanism is installed in the machine.
Normally the amount for a selection is cashed after the machine
sends the message “Selection successful”, consequently the
change is returned at the end of dispensing the selected product.
By enabling this function, disabled by default, the cashed signal is
sent at the beginning of dispensing, consequently the change owed
to the user is returned at the same time of dispensing the product.
2.1.3
de c I m a l P o I n t
Press the conrm key “” to display the position of the decimal
point, i.e.:
0 decimal point disabled
1 XXX.X
2 XX.XX
3 X.XXX
Press the conrm key “”, these values will start blinking and can
then be modied as necessary.