Nederman FE840 PLUS User manual

REV.1 1023
Operation Manual
Portable and Compact Extraction Units
Fume Eliminator
FE840 PLUS

Fume Eliminator

Fume Eliminator
1 Preface....................................................................................................................................................6
2 Notices....................................................................................................................................................6
3 Description ...........................................................................................................................................6
3.1 Function ................................................................................................................................6
3.2 Technical Data ....................................................................................................................7
4 Fume Eliminator Operation ...........................................................................................................7
4.1 Operation ..............................................................................................................................7
5 Maintenance ........................................................................................................................................7
5.1 Changing Carbon Brushes ..............................................................................................7
5.2 Changing Filter and Emptying the Coarse Separator .........................................8
5.3 Spare Parts ...........................................................................................................................8
6 Recycling ...............................................................................................................................................8
Figures .......................................................................................................................................................5
Table of Contents
Nederman Customer Service & Technical Support [e-mail] [phone]
3
Declaration of Conformity .................................................................................................................4
Notes......... ..................................................................................................................................................8

Fume Eliminator
Declaration of Conformity
Declaration of conformity
We, AB Ph. Nederman & Co., declare under our sole responsibility that the
Nederman product:
Fume Eliminator (Part No. **, and stated versions of **) to which this
declaration relates, is in conformity with all the relevant provisions of the
following directives and standards:
Directives
2006/42/EC, 2014/30/EU, 2014/35/EU.
Standards
EN 60204-1, EN ISO 12100, EN ISO 15012-1,EN 61000-4-4.
The name and signature at the end of this document, is the person
responsible for both the declaration of conformity and the technical file.
AB Ph. Nederman &
Co. P.O. Box 602
SE-251 06
Helsingborg Sweden
Lars Nagy
Manager Product
Centre 2016-08-15
**
2161419
Nederman Customer Service & Technical Support [email protected] [phone]
4

Fume Eliminator
1
4 2
1-3/4"
(45 mm)
8.2 ft
(2.5 m)
31.9"
(810 mm)
16.1"
(410 mm)
8.9"
(225 mm)
Wiring diagram
Figures
1
2
X
3
5
3

Fume Eliminator
1 Preface
This manual is for the proper installation, use and maintenance of this product. Please
review it carefully before using this product or completing any maintenance. Replace
the manual immediately if lost.
All installation, repair and maintenance should be completed by qualified personnel
using only original spare parts. Contact the nearest authorized distributor or Nederman
for advice on technical service and obtaining spare parts.
Nederman continuously improves its products’ design and efficiency through
modifications, and reserves the right to do so without introducing these improvements
to previously supplied products. Nederman also reserve the right to, without previous
notice, modify data and equipment as well as operating and maintenance instructions.
This document contains important information that is presented either as a warning,
caution or note. See the following examples:
WARNING! (injury)
Warnings indicate a potential hazard to the health and safety of personnel, and
how that hazard can be avoided.
CAUTION! (risk)
Cautions indicate a potential hazard to the product but not to personnel nor how
that hazard can be avoided
Notes contain information important to personnel
3.1 Function
See Figure 2 Page 5.
1. Handle and lock for the coarse separator
2. Coarse separator
3. Power switch
4. Exhaust
6
Nederman Customer Service & Technical Support [email protected] [phone]
2 Notices
3 Description

Fume Eliminator
3.2 Technical Data
Table 3-1: Technical data
Dimensions See Figure 2 page 5
Noise level 75 dB(A) ISO 11201
Weight 30 lbs (13.6 kg)
Voltage 120V 60 Hz
Power 1.3 hp (1 kW)
Max. Working Pressure 64 in. w.g. (16 kPa)
Air Flow Capacity 88 cfm (150 m3/h)
Filter Area 54 ft2 (5.3 m2)
Filtration Efficiency
4.1 See Figure 2 page 5
FE840 PLUS (Manual)
Switch (3) to ON position. The unit will work continuously.
Installation, repair and maintenance work must be completed by qualified
personnel using only original Nederman spare parts. Please contact your
nearest authorized distributor or Nederman for advice on technical service.
NOTE! The service intervals in this chapter are based on the unit being professionally
maintained.
5.1 Changing Carbon Brushes
WARNING! Risk of personal injuries.
• Remove the power cabl;e plug before perfoming any motor maintenance.
• The carbon brushes are to be replaced by a qualified electrician. Instructions
for proper fitting are included with every brush set.
Nederman Customer Service & Technical Support [email protected] [phone]
7
4 Fume Eliminator Operation
Hose Diameter 1-3/4" (45 mm)
Hose Length 8.2 ft (2.5 m)
840 NANO
F9 - W3 - MERV 14 - 99% (carbon reinfoced nanofiber)
5 Maintenance

Fume Eliminator
5.2 Changing Filter and Emptying the Coarse Separator
See Figure 2 Page 5. A new filter needs to be installed when the suction
becomes inadequate. The coarse separator usually needs to be emptied only
when the filter is changed, but heavy use of some types of electrodes may
require more frequent emptying.
How to change filter:
1. Switch off the unit. Remove suction hose.
2. Turn handle (A) down and remove the coarse separator (C).(The
handle works as a lock for the coarse separator).
3. Pull out and dispose the old filter.
4. Insert a new filter.
5. Unscrew the locking screw (D) and remove outer part.
6. Empty the coarse separator.
7. Check the separator rubber seal for any signs of damage.
8. Reassemble the coarse separator. Lock the handle.
NOTE! The coarse separator is locked partially when the handle is in the upright
position and fully locked when handle it is down position.
5.3 Spare Parts
Contact your nearest authorized distributor or Nederman for advice on technical
service or if help with spare parts is required. Also visit www.nederman.com.
When ordering spare parts always state the following:
•Part number and control number (see the product name plate)
•Description and name of the spare part (see www.nederman.com).
•Quantity of the parts required.
6 Recycling
The product has been designed for component materials to be recycled. Its different
material types must be handled according to relevant local regulations. Contact the
distributor or Nederman if uncertainties arise when scrapping the product at the end
of its service life.
Nederman Customer Service & Technical Support [email protected] [phone]
8

Notes
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
Nederman Customer Service & Technical Support [e-mail] [phone]
9
Fume Eliminator

The Nederman Group is one of the World’s leading suppliers of products and solutions within
the environmental technology sector focusing on industrial air filtration and recycling. These
products and solutions reduce the environmental impact of industrial production and create
safe and clean working environments while boosting production efficiency.
The group’s offering covers the design stage through installation, commissioning and servicing
with subsidiaries in 29 countries and agents and distributors in over 30 countries.
Nederman is ISO 9001 and 14001 certified and develops and produces in its own manufacturing
and assembly facilities in Europe, North America and Asia.
Nederman Service Capabilities
Nederman has certified service partners trained extensively in servicing our machinery. Make
sure to choose a certified technician to service your Nederman equipment as they have the
correct tools and knowledge to solve any machinery issues and improve its performance. Be
sure to ask if your technician is certified by Nederman.
Our services for fume & dust collection systems are customized to your particular needs. We
work with you to understand your needs, then develop a program to meet your specific
needs. Our services include: (not all services available in all locations)
Bag & Filter Change-outs
Bag Selection Recommendations
Collector Re-builds
Dye Testing for Leakage
Electrical Tests - Current, Voltage
Emergency Call-outs
Filter Media Analysis
Mechanical Survey and Repair
Multi-year Contracts
New Collector Start-up Service
On-going Technical Support
Preventative Maintenance Programs
Repair and Replace
Gauges/Timers/Valves
Stack Emission Testing
Training Programs
Troubleshooting / Auditing
Velocity, Pressure and Temperature Tests
Written Service Report
Customer Service and Technical Support
Nederman Corporation USA
4404-A Chesapeake Drive
Charlotte, NC 28216
336-821-0800
www.nederman.com
Nederman Customer Service & Technical Support [e-mail] [phone]
10