Neptronic TSU00 Series User manual

Standalone Wall-Mount Controller
Specification and Installation Instructions
TSU-200324 Page | 1
Models
Model
Temp
RH
PIR
TSU00-110
●
TSU00-111
●
●
TSU00-114
●
●
TSU00-115
●
●
●
Description
The TSU is a standalone wall-mount controller with a built-in temperature
sensor. The unit is designed for simple and accurate control of a fan coil
unit or heating/cooling equipment. Its field configurable algorithms enable
versatile implementation of required control sequences.
Featuring an external humidity sensor input for accurate humidity control,
this comprehensive unit also provides a dehumidification sequence
compensated by auto activation of reheat output.
The controller is available with additional sensors, such as the PIR motion
detection and humidity sensor, providing more functionality for the terminal
device.
TSU00 Series
Features
•Fan control: 1, 2 or 3-speed (auto/on), or analog (ECM)
•Optional internal/external humidity sensor input for simple and accurate humidity control
•Dehumidification sequence compensated by auto activation of reheat output
•Real time clock (RTC) with 24-hour backup
•7-day programmable schedule
•Precise temperature control with configurable PI (Proportional-Integral) function
•Selectable internal or external temperature sensor
•Low limit set protection (10°C / 50°F)
•Occupancy and night set back (NSB) mode
•Select direction on outputs
•Select controller’s default display
•Multi-level lockable access menu and setpoint
•Selectable Fahrenheit or Celsius scale
•Option of pulse/floating/on-off output on binary outputs
•Internal/external occupancy input
•Compressor anti-cycling delay (configurable)
•ΔT control (on request)
Onboard Sensors
•Temperature sensor (°C/°F)
•Humidity sensor (%RH), select models
•PIR motion detection sensor, select models

Standalone Wall-Mount Controller
Specification and Installation Instructions
www.neptronic.com Page | 2
Technical Specifications
Description
TSU Series
Temperature Sensor
Setpoint Range
10ºC to 40ºC [50ºF to 104ºF]
Control Accuracy
Temperature: ±0.4ºC [0.8ºF]
Display Resolution
±0.1ºC [0.2ºF]
Humidity Sensor (select models)
Setpoint Range
10% to 90% RH
Control Accuracy
±3.5% RH
Display Resolution
0.1%
PIR Motion Sensor (select models)
Operating Principle
Passive Infrared (PIR)
Detection Angle
100º
Detection Distance
4m [13ft]
Detection Area
100º
4m
(13ft)
Other
Inputs
2 Universal Inputs (0-10Vdc, 10KΩ sensor, dry contact)
Outputs
5 Binary Outputs (OptoFET, 250mA max)
2 Analog Outputs (0-10Vdc, adjustable)
Power supply
22 to 26 Vac 50/60Hz
Power consumption
1 VA max
Proportional band
0.5ºC to 5ºC [1ºF to 9ºF] adjustable (heat/cool/reheat independent)
Dead band
0.0ºC to 5ºC [0.0ºF to 9ºF] adjustable (heat/cool/reheat independent)
Electrical connection
0.8 mm2 [18 AWG] minimum
Operating temperature
0ºC to 50ºC [32ºF to 122ºF]
Storage temperature
-30ºC to 50ºC [-22ºF to 122ºF]
Relative Humidity
5 to 95% noncondensing
Degree of protection of housing
IP 30 (EN 60529)
Weight
135 g. [0.30 lb]
Dimensions:
A = 4.88” | 124mm
B = 3.25” | 83mm
C = 1.75” | 44mm
D = 0.96” | 24mm
E = 2.07” | 53mm
F = 2.36” | 60mm
G = 3.28” | 83mm
H = 0.78” | 20mm
E
D
B
A
CPIR Sensor
(Optional)
G
F
H

Standalone Wall-Mount Controller
Specification and Installation Instructions
www.neptronic.com Page | 3
Wiring
1
2
3
4
7
6
5
8
9
10
11
12
13
14
15
PGM
RUN
JP1
We strongly recommend that all Neptronic
products be wired to a separate grounded
transformer and that transformer shall service
only Neptronic products. This precaution will
prevent interference with, and/or possible damage
to incompatible equipment.
Terminal Description
Terminals
Option Heat Pump
Analog Option
1-Speed Fan
2-Speed Fan
3-Speed Fan
Fan analog
1-Speed Fan
2-Speed Fan
3-Speed Fan
TB1
1
COM (PWR)
Common (power input)
Common (power input)
2
24 Vac (PWR)
24 Vac (power input)
24 Vac (power input)
3
COM (BO)
Common (for binary output)
Common (for binary output)
4
N/A
N/A
N/A
5
N/A
N/A
N/A
6
BO3
Heat W1
select any ramp*
7
BO4
Compressor Y2
Compressor Y2
Fan (speed 3)
select any ramp*
Fan (speed 3)
8
BO5
Heat W2
Fan (speed 2)
Fan (speed 2)
select any ramp*
Fan (speed 2)
Fan (speed 2)
9
BO6
Fan (speed 1)
Fan (speed 1)
Fan (speed 1)
select any ramp*
Fan (speed 1)
Fan (speed 1)
Fan (speed 1)
10
BO7
select any ramp*
select any ramp*
11
AO2
select any ramp*
Fan Speed option
•Modulating
0-10Vdc for ECM Motors
•Steps of 3,6,9V for 3 Speed
select any ramp*
12
AO3
select any ramp*
select any ramp*
13
COM
Common
Common
14
UI1
Universal Input selection:
•0-10 Vdc (External sensor, humidity, CO2)
•10K Ohm (External sensor, changeover)
•Dry Contact**
Universal Input selection:
•0-10 Vdc (External sensor, humidity, CO2)
•10K Ohm (External sensor, changeover)
•Dry Contact**
15
UI2
* = select from any of the following ramps:
** = select from any of the following:
•Cooling 1 w/ fan
•Cooling 2 w/ fan
•Heating 1 w/ fan
•Heating 2 w/ fan
•Heating 2 without fan
•Cool/Heat 1 w/ fan
•COR (changeover) w/ fan
•Humidify w/ fan
•CO2Alarm
•Off
•Off
•Override
•Flow Switch
•Local/Remote Selector Switch
•Overheat
•Dirty Filter
•Window & Door Contacts
•Occupancy & NSB Sensor
•Changeover Input

Standalone Wall-Mount Controller
Specification and Installation Instructions
www.neptronic.com Page | 4
Interface
AM PM
F
C
%RH
Network
Communication
User Lock
Programming Mode
(Technician Setting)
Alarm Status
Energy Saving Mode
(NSB/OCC)
AM PM
Time
°C
°F
%RH
ºC: Celsius Scale
ºF: Fahrenheit Scale
%RH: Humidity
A
Automatic Mode
Cooling
Heating
Fan
Humidify/
De-humidify
Mounting Instructions
CAUTION: Remove power to avoid a risk of malfunction.
A. Remove the captive screw that’s holding the base and the front cover of the unit together.
B. Lift the front cover of the unit to separate it from the base.
C. Pull all wires through the holes in the base.
D. Secure the base to the wall using wall anchors and screws (supplied). Make the appropriate connections.
E. Mount the control module on the base and secure using the screw.
ABC D E
Programming Mode
The Mode Selector jumper JP1 must be set to the PGM position (Programming Mode). Refer to the Wiring section on page
3. To exit, set the jumper back to the RUN position (Operation Mode). Changes are saved as soon as they are made.
Setting Value
Advance to next setting
Change value
Return to previous setting

Standalone Wall-Mount Controller
Specification and Installation Instructions
www.neptronic.com Page | 5
Symbols used in this Manual
Icon
Description
Icon
Description
Icon
Description
Icon
Description
Temperature
Heating
Cooling
Humidity
Fan
Analog Output 2
Analog Output 3
Time
Binary Output 3
Binary Output 4
Binary Output 5
Binary Output 6
BO7
Binary Output 7
UI1
Universal Input 1
UI2
Universal Input 2
Night Set Back
Occupancy
Valve
Lock
Carbon Dioxide
Setpoint and User Control
“Intern Temp Sensor Offset”
Range:
Offset:
Increment:
0ºC to 50ºC [32ºF to 122ºF]
Max. ± 5ºC [± 9ºF]
0.1ºC [0.2ºF]
Compare the displayed temperature reading with a known value from a thermometer or other temperature sensing device. To
offset or calibrate the sensor, use the arrow buttons to set the desired temperature reading. This is useful for controllers
installed in areas where the temperature read is slightly different than the room’s actual temperature. For example, a controller
placed right under the air diffuser.
“Minimum User Setpnt”
Default:
Range:
Increment:
15ºC [59ºF]
10ºC to 40ºC [50ºF to 104ºF]
0.5ºC [1.0ºF]
In Operation mode, you cannot decrease the setpoint to less than the value set as the minimum user point. The minimum value
is restricted by the maximum value set at Step 3, “Maximum User Setpnt”. In other words, the value that is set as the minimum
cannot be greater than the maximum value.
“Maximum User Setpnt”
Default:
Range:
Increment:
30ºC [86ºF]
10ºC to 40ºC [50 to 104ºF]
0.5ºC [1.0ºF]
In Operation mode, you cannot increase the setpoint to more than the value set as the maximum user point. The maximum
value is restricted by the minimum value set at Step 2, “Minimum User Setpnt”. In other words, the value that is set as the
maximum cannot be less than the minimum value.
“User Setpnt locked”
Default:
Range:
No (Unlocked)
No (Unlocked), yES (Locked)
If set to No, the user setpoint option is not locked and the user can adjust the desired temperature setpoint. If set to yES, the
user setpoint option is locked and the user cannot set the desired temperature setpoint. A lock symbol appears to indicate
that the setpoint is locked.
“User Setpnt”
Default:
Range:
Increment:
22ºC [72ºF]
10ºC to 40ºC [50ºF to 104ºF]
0.5ºC [1.0ºF]
Set the desired temperature setpoint within the defined range. If the setpoint option was locked at Step 4, “User Setpnt locked”,
a lock symbol is displayed. The setpoint value is restricted by the minimum at Step 2, “Minimum User Setpnt”and maximum
at Step 3, “Maximum User Setpnt” values. In other words, the setpoint should be within the minimum and maximum setpoint
range.

Standalone Wall-Mount Controller
Specification and Installation Instructions
www.neptronic.com Page | 6
“Temp Control Mode”
Default:
Range:
COOL(Cooling Only)
Auto (Automatic), HEAt (Heating Only), COOL(Cooling Only), On (Cooling or Heating),
CLHt (Automatic only)
Select the control mode that you want to authorize to the user. To authorize all the available modes, select Auto (Automatic
Mode). The cooling and heating symbols are also displayed. The selection made at this step determines the options
available via the Control Mode (see page 30).
“Enable On Off Control Mode”
Default:
Range:
yES (Enable)
yES (Enable), No (Disable)
If set to yES, the user can set the unit to “Off” via the Control Mode (see page 30). If set to No, the “Off” selection does not
appear in the Control Mode.
"Display Info"
Default:
Range:
t - Hu %RH °C (temperature, humidity, and cooling heating demand)
t - Hu %RH °C (temperature, humidity), StP %RH °C (temperature, humidity setpoint), OFF (no display),
t - Hu %RH °C (temperature, humidity, and cooling heating demand), StP %RH °C (temperature, humidity setpoint, and cooling
heating demand)
Select the desired information to appear on the display.
Keypad Lock Settings
“Keypad Upper Left Locked”
Default:
Range:
No (Disable)
yES (Enable), No (Disable)
If set to yES, the button is locked and cannot be used by the user. If set to No, the button is unlocked and can be used
by the user.
“Keypad Lower Left Locked”
Default:
Range:
No (Disable)
yES (Enable), No (Disable)
If set to yES, the button is locked and cannot be used by the user. If set to No, the button is unlocked and can be
used by the user.
“Keypad Arrows Locked”
Default:
Range:
No (Disable)
yES (Enable), No (Disable)
If set to yES, the and buttons are locked and cannot be used by the user. If set to No, the and buttons are
unlocked and can be used by the user.
Heat Pump Settings
"Heat Pump Option"
Default:
Range:
OFF (Disable)
ON (Enable), OFF (Disable)
Enable or disable the heat pump option.
If you select OFF:
•Heat Pump options (Steps 13 to 15 and 35) will not be available.
•Binary Output ramps (Steps 36, 42, 48 and 54) will be available.
If you select ON:
•Heat Pump options (Steps 13 to 15 and 35) will be available.
•Binary Output ramps (Steps 36, 42, 48 and 54) will not be available.

Standalone Wall-Mount Controller
Specification and Installation Instructions
www.neptronic.com Page | 7
"Revers Valve O/B"
Default:
Range:
o
o, b
This option appears only if you have selected ON at Step 12, "Heat Pump Option". Set the mode in which the reversing valve is
energized; cooling mode (o) or heating mode (b). The cooling symbol is displayed if you select oand heating symbol is
displayed if you select b.
"EMH Output"
Default:
Range:
dIS (Disable)
dIS (Disable), ENA (Enable)
This option appears only if you have selected ON at Step 12, "Heat Pump Option". Select ENA to enable emergency heat (EMH)
outputs W1 and W2, and the EMH option via the Control Mode (see page 30). Select dIS to disable EMH availability. The heating
symbol is also displayed.
If you select dIS, Step 15,"EMH Auto Mode" will not be available.
If you select ENA, Step 15,"EMH Auto Mode" will be available.
"EMH Auto Mode"
Default:
Range:
NO (Disable)
YES (Enable), NO (Disable)
This option appears only if you have selected ENA at Step 14, "EMH Output". If you select YES, the emergency heat (EMH)
will be operational in Automatic mode. If you select NO, the EMH will not be operational in Automatic mode. The heating
symbol is also displayed.
Valve Settings
“Valve Size”
Default:
Range:
1”
1/2”, 3/4”, 1”
Select the desired valve size in inches for the 6-way valve from the available options.
Analog Output 2 (AO2)
"AO2 Ramp"
Default:
Range:
Hr1 (Heating Ramp 1)
Cr1, Cr2, Hr1, Hr2 (heat with fan), Hr2 (heat without fan), CH1, HU, CO2, 6w, dto, VFdt, VFdP, FAN,
OFF, COr
Select the desired signal from the available options.
•Cr1 (Cooling Ramp 1) or Cr2 (Cooling Ramp 2). The Cr1 and Cr2 ramps are used for cooling. If selected, the controller
performs cooling based on the cooling proportional, integral, and dead band values.
•Hr1, Hr2 (heat with fan), or Hr2 (heat without fan). The Hr1 and Hr2 ramps are used for heating. If selected, the controller
performs heating based on the heating proportional, integral, and dead band values.
•CH1 (Cooling and Heating). If selected, the controller performs cooling regularly. If another output is set to heat, it
performs heating regularly.
•HU (Humidify). If selected, the controller modulates the output based on the humidify demand.
•CO2 (Carbon dioxide). If selected, the controller will activate or deactivate the output based on carbon dioxide levels.
•6W (6-way Valve). If selected, the controller will modulate the 6-way valve depending on the heating or cooling demand.
•dto (Delta temperature control). If selected, the controller will modulate the ΔT control based on the inlet and outlet
temperature of the water inside the fan coil unit.
•VFdt (VFD Temp Loop). If selected, the controller will modulate the VFD fan based on the selected temperature input.
•VFdP(VFD Pressure Loop).If selected, the controller will modulate the static pressure based on the reading and the
pressure setpoint.
•FAN. The FAN option is available only if you selected OFF at Step 12, "Heat Pump Option". If selected, the controller
modulates the output based on the Fan demand.
•OFF. If selected, the controller does not use the output.
•COr (Changeover). If selected, the controller will modulate heating and cooling, as appropriate.
If you select OFF, Steps 18 to 20 will not be available.
If you select VFdt or VFdP,Steps 28 to 33 will not be available.

Standalone Wall-Mount Controller
Specification and Installation Instructions
www.neptronic.com Page | 8
If you select CH1, Step 27, "Minimum Cool 1 Heat 1 Percent" will be available.
If you select FAN, Step 28, "Fan Spd Signal" will not be available.
Cr1
Cr2
Hr1
Hr2 (with fan)
Hr2 (without fan)
CH1
HU
CO2
6W
dto
VFdt
VFdP
FAN
OFF
COr
"AO2 Minimum Voltage"
Default:
Range:
Increment:
0.0 Volt
0.0 to 10.0 Volts
0.1 Volt
This option does not appear if the signal ramp for AO2 is set to OFF (Step 17, "AO2 Ramp"). Select the desired minimum voltage
(“zero” value) for the AO2 ramp. The minimum value is restricted by the maximum value at Step 19, "AO2 Maximum Voltage". In
other words, the minimum value should be less than the maximum value.
"AO2 Maximum Voltage"
Default:
Range:
Increment:
10.0 Volts
0.0 to 10.0 Volts
0.1 Volt
This option does not appear if the signal ramp for AO2 is set to OFF (Step 17, "AO2 Ramp"). Select the desired maximum
voltage (“span” value) for the AO2 ramp. The maximum value is restricted by the minimum value at Step 18, "AO2 Minimum
Voltage". In other words, the maximum value should not be less than the minimum value.
"AO2 Dirrev"
Default:
Range:
dir (Direct)
dir (Direct), rEV (Reverse)
This option does not appear if the signal ramp for AO2 is set to OFF (Step 17, "AO2 Ramp"). Set the direction of the analog
signal to either Direct (e.g. 0 to 10Vdc), or Reverse (e.g. 10 to 0Vdc).
”AO2 Signal Type”
Default:
Range:
ANLg (Analog Output)
ANLg (Analog Output), OnOF (On/Off), PuLs (Pulsing)
This option does not appear if the signal ramp for AO2 is set to OFF (Step 17, "AO2 Ramp"). Set the signal type for AO2 toeither
Analog Output, On/Off or Pulsing.
Analog Output 3 (AO3)
“AO3 Ramp”
Default:
Range:
Hr1 (Heating Ramp 1)
Cr1, Cr2, Hr1, Hr2 (heat with fan), Hr2 (heat without fan), CH1, HU, CO2, 6W, dto, OFF, COr
Select the desired signal from the available options. The AO2 input signal has priority over AO3.
•Cr1 (Cooling Ramp 1) or Cr2 (Cooling Ramp 2). The Cr1 and Cr2 ramps are used for cooling. If selected, the controller
performs cooling based on the cooling proportional, integral, and dead band values.

Standalone Wall-Mount Controller
Specification and Installation Instructions
www.neptronic.com Page | 9
•Hr1, Hr2 (heat with fan), or Hr2 (heat without fan). The Hr1 and Hr2 ramps are used for heating. If selected, the controller
performs heating based on the heating proportional, integral, and dead band values.
•CH1 (Cooling and Heating). If selected, the controller performs cooling regularly. If another output is set to heat, it
performs heating regularly.
•HU (Humidify). If selected, the controller modulates the output based on the humidify demand.
•CO2 (Carbon dioxide). If selected, the controller will activate or deactivate the output based on carbon dioxide levels.
•6W (6-way Valve). If selected, the controller will modulate the 6-way valve depending on the heating or cooling demand.
•dto (Delta temperature control). If selected, the controller will modulate the ΔT control based on the inlet and outlet
temperature of the water inside the fan coil unit.
•OFF. If selected, the controller does not use the output.
•COr (Changeover). If selected, the controller will modulate heating and cooling, as appropriate.
If you select OFF, Steps 23 to 26 will not be available.
If you select CH1, Step 27, "Minimum Cool 1 Heat 1 Percent" will be available.
If you select FAN, Step 28, "Fan Spd Signal" will not be available.
Cr1
Cr2
Hr1
Hr2 (with fan)
Hr2 (without fan)
CH1
HU
CO2
6w
dto
OFF
Cor
“AO3 Minimum Voltage”
Default:
Range:
Increment:
0.0 Volt
0.0 to 10.0 Volts
0.1 Volt
This option does not appear if the signal ramp for AO3 is set to OFF (Step 22, “AO3 Ramp”). Select the desired minimum voltage
(“zero” value) for the AO3 ramp. The minimum value is restricted by the maximum value at Step 24, “AO3 Maximum Voltage”. In
other words, the minimum value should be less than the maximum value.
“AO3 Maximum Voltage”
Default:
Range:
Increment:
10.0 Volts
0.0 to 10.0 Volts
0.1 Volt
This option does not appear if the signal ramp for AO3 is set to OFF (Step 22, “AO3 Ramp”). Select the desired maximum
voltage (“span” value) for the AO3 ramp. The maximum value is restricted by the minimum value at Step 23, “AO3 Minimum
Voltage”. In other words, the maximum value should not be less than the minimum value.
“AO3 Dirrev”
Default:
Range:
dir (Direct)
dir (Direct), rEV (Reverse)
This option does not appear if the signal ramp for AO3 is set to OFF (Step 22, “AO3 Ramp”). Set the direction of the analog
signal to either Direct (e.g. 0 to 10Vdc), or Reverse (e.g. 10 to 0Vdc).
“AO3 Signal Type
Default:
Range:
ANLg (Analog Output)
ANLg (Analog Output), OnOF (On/Off), PuLs (Pulsing)
This option does not appear if the signal ramp for AO3 is set to OFF (Step 22, “AO3 Ramp”). Set the signal type for AO3 to either
Analog Ouptut, On/Off or Pulsing.

Standalone Wall-Mount Controller
Specification and Installation Instructions
www.neptronic.com Page | 10
"Minimum Cool 1 Heat 1 Percent"
Default:
Range:
Increment:
0 %
0 to 100%
5 %
This option appears if you have selected CH1 at Step 17, "AO2 Ramp" or at Step 22, “AO3 Ramp”. Set the percentage at
which the controller sets the CH1 output during heating, provided another output has also been set to heating.
Fan Settings
"Fan Spd Signal"
Default:
Range:
3
1, 2, 3
This option does not appear if you have selected FAN at Step 17, "AO2 Ramp". Select the desired number of fan speed
contacts. The fan symbol is also displayed.
"Fan Speed Option"
Default:
Range:
Std (Standard)
AdV (Advanced), Std (Standard)
Select between the Standard (Neptronic) and Advanced (OE1) fan speed specifications. The fan symbol is also displayed.
"Enable Fan Contrl Mode"
Default:
Range:
No (Disable)
yES (Enable), No (Disable)
This option appears only if you have selected Adv at Step 29, "Fan Speed Option". Select to enable or disable the fan control
mode option. If you select No, the Fan Speed Selection Mode option is not available in Control Mode. The fan symbol is
also displayed.
"Hide Fan Display Info"
Default:
Range:
No (Disable)
yES (Enable), No (Disable)
Select to enable or disable the fan display information. If you select Yes, the Fan demand (fan icon) does not appear on the
display and the Fan Speed Selection Mode is disabled. The fan symbol is also displayed.
"Fan Auto Mode"
Default:
Range:
yES (Enable)
yES (Enable), No (Disable)
If set to yES, the user can set the fan speed to "Automatic" via the Fan Speed Selection Mode (see page 31). If set to No, the
"Automatic" speed does not appear in the Fan Speed Selection Mode. The fan symbol is also displayed.
If you select yES, Step 33 "Fan Auto Timeout Seconds" will be available.
If you select No, Step 33 "Fan Auto Timeout Seconds" will not be available.
"Fan Auto Timeout Seconds"
Default:
Range:
Increment:
120 seconds
0 to 255 seconds
1 second
This option appears only if you have selected yES at Step 32, "Fan Auto Mode". Select the desired value for the automatic
shutoff delay when there is no demand. The fan symbol is also displayed.
"Damping Factor Time In Seconds"
Default:
Range:
Increment:
0 second
0 to 255 seconds
1 second
Select the desired damping factor value for the fan. The fan symbol is also displayed.