NEW BRUNSWICK SCIENTIFIC innova 4230 User manual

OPTIONAL
PHOTOSYNTHETIC
LIGHT ASSEMBLY
MANUAL NO.: M1233-0051
REVISION F
NEW BRUNSWICK SCIENTIFIC CO., INC.
BOX 4005 . 44 TALMADGE ROAD . EDISON, NJ 08818-4005 . 732-287-1200
TELEPHONE: [phone] . FAX: [phone] . TELEX: 4753012 NBSCO
INTERNET: http://www.nbsc.com/ . E-MAIL: [e-mail]

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD
WARRANTY
Innova shakers are warranted by New Brunswick Scientific Co., Inc. for two
years or 10,000 hours of actual shaker use, whichever comes later. This
warranty covers parts and labor for the entire machine with the exception of
glassware and its contents, illumination tubes and associated starters. This
warranty covers faulty components and assembly, and our obligation under this
warranty is limited to repairing or replacing the shaker or part thereof, which
shall within two years after date of shipment, or 10,000 hours of operating time,
(whichever comes later), prove to be defective after our examination. THIS
WARRANTY DOES NOT COVER ANY LOSS OF TIME, MATERIALS,
BIOLOGICAL OR BIOCHEMICAL BY-PRODUCTS CAUSED BY ANY
WORK INTERRUPTION RESULTING FROM SHAKER FAILURE, NOR
DOES IT EXTEND TO ANY INNOVA SHAKER WHICH HAS BEEN
SUBJECTED TO MISUSE, NEGLECT, ACCIDENT OR IMPROPER
INSTALLATION OR APPLICATION. IN ADDITION, THE WARRANTY
DOES NOT APPLY TO ANY INNOVA SHAKER THAT HAS BEEN
REPAIRED OR ALTERED OUTSIDE THE NBS FACTORY WITHOUT
PRIOR AUTHORIZATION FROM NEW BRUNSWICK SCIENTIFIC CO.,
INC.. For a period of two years (or more) after the shipment date the Innova
warranty will be in effect as long as the shaker has not been in operation for a
total of 10,000 hours.
After the 10,000 hours of operating time have elapsed the Innova warranty may
still be in effect as long as the two-year minimum warranty period has not been
reached. Operating time is based on actual usage of the shaker, as determined
by the shaker’s internal electronic clock. Any tampering or alteration of the
electronic clock will void the 10,000 hr. warranty.

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD
INNOVA 4230 - LIGHT MANIFOLD
COPYRIGHT NOTICE
New Brunswick Scientific Co., Inc.©1990. All rights reserved. No part of this manual may
be reproduced in any form without the express written permission of NBS.
DISCLAIMER
NBS reserves the right to change specifications without notice as part of our continu-
ing program of product improvement.

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD
INTRODUCTION
The Innova 4230 Photosynthetic Light Assembly will provide you with reliable
and maintenance-free operation which is characteristic of all NBS products. The
Innova 4230 is among the newest generation of NBS products and incorporates
a variety of state-of-the-art components and features for your exacting scientific
experiments.

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD
HOW TO USE THIS MANUAL
This Manual is intended to provide the user with an understanding of how the
Innova 4230 Photosynthetic Light Assembly operates, its basic components, and
information about preventive maintenance and service issues. This Manual also
includes a guide to the installation and operation of the Photosynthetic Light
Assembly.
The Manual is divided into three basic sections. Section I provides an overview
of the Innova 4230 Photosynthetic Light Assembly. Section II details the set-up
and operation of the instrument. Section III outlines the service procedures
which should be utilized by a qualified service engineer.
It is recommended that you completely familiarize yourself with this Manual,
prior to actually operating the Photosynthetic Light Assembly.

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD
TABLE OF CONTENTS
PAGENO.
INTRODUCTION
Warranty Statement
How to Use This Manual
INNOVA OVERVIEW, GENERAL PRODUCT DESCRIPTION
General Description................................................................................... 1
INNOVA OPERATION
Installation and Set-Up
Unpacking...................................................................................... 2
Light Manifold Installation......................................................................... 2
Cleaning/Maintenance................................................................................. 5
SERVICE AND MAINTENANCE
Lamp Replacement..................................................................................... 6
Lamp Starter Replacement.......................................................................... 6
Service Parts List........................................................................................ 7

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD 1
OVERVIEW
GENERAL DESCRIPTION
The 4230 Photosynthetic Light Assembly has six 15 watt fluorescent grow lamps which are
designed specifically for photosynthetic investigations.

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD 2
OPERATION
INSTALLATION & SET UP
UNPACKING
Upon unpacking the unit, inspect it carefully for any apparent damage which may have
occurred during transit. Report any damage to the carrier and to the New Brunswick
Scientific Co., Inc. Service Department at 1-800-631-5417. Do not discard the crate or
packing material.
LIGHT MANIFOLD INSTALLATION
1. Place the power switch in the OFF position. Disconnect the unit from its power source.
2. Install (4) bracket clips (K0280-0550) provided with Light Manifold into the (4) rails
located on interior wall of unit, (see Figure 1) at location desired.
3. Set selector switch (located in rear right-hand corner of Light Manifold) to the proper
voltage shown on electrical label for Innova 4230 unit. (See Figure 2 for setting of
switch.)
4. Locate interior socket mounted on rear wall of interior chamber (in upper right-hand
corner), socket is labeled 500 VA. Unscrew protective cap.
5. Install power cord located on rear of Light Manifold into socket and mount Light
Manifold Assembly onto bracket clips installed in note #2.
6. Re-connect unit to its power source.
7. Place main power and interior socket switches in the ON position.
WARNING:
LIGHT MANIFOLD MUST BE LOCATED BELOW
THE FAN (SEE FIGURE 1).

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD 3
OPERATION
FIGURE 1 - MOUNTING

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD 4
OPERATION
100
117
220
240
FUSE HOLDER
SELECTOR
DIRECTIONS FOR SETTING SELECTOR SWITCH
(LOCATED IN REAR OF UNIT)
1. USING FLAT BLADED SCREW DRIVER REMOVE
FUSE HOLDER
2. USING COIN, ROTATE SELECTOR UNTIL PROPER VOLTA
G
FOR UNIT IS INDICATED NEXT TO ARROW ON
SELECTOR SWITCH.
3. REINSTALL FUSE HOLDER.
FIGURE 2 - SELECTOR SWITCH

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD 5
OPERATION
CLEANING/MAINTENANCE
The Innova Light Manifold requires no routine maintenance.
Do not use abrasive or corrosive compounds to clean this module, as they may damage the
unit and void the warranty.
The Light Manifold diffuser should only be cleaned with a non-abrasive glass cleaner.

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD 6
SERVICE AND MAINTENANCE
LAMP REPLACEMENT
1. Turn the power OFF.
2. Open the chamber door, and remove the shaker platform (see Shaking Machine Manual
for instructions on how to remove the platform) that is just below the Light Manifold.
3. Remove the two set screws and clips mounted on the front side of the Light Manifold
Assembly (before removing these screws hold the diffuser in place). Then remove the
diffuser panel.
4. Carefully rotate the lamp to remove it from its sockets.
5. Install the new lamp by sliding into the slots on the sockets and rotating it unit it snaps
into place.
6. Replace the diffuser panel.
LAMP STARTER REPLACEMENT
1. Turn the unit OFF.
2. Open the chamber door, and remove the shaker platform (see Shaking Machine Manual
for instructions on how to remove the platform) that is just below the Light Manifold.
3. Remove the two screws and clips mounted on the front side of the Light Manifold
Assembly (before removing these screws hold the diffuser in place). Then remove the
diffuser panel.
WARNING:
BEFORE PERFORMING ANY SERVICE OR
MAINTENANCE ON THE INSTRUMENT, TURN THE
POWER OFF USING THE ON/OFF SWITCH ON THE
CONTROL CONSOLE AND DISCONNECT THE UNIT OF
ITS POWER SOURCE.

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD 7
SERVICE AND MAINTENANCE
4. Locate the defective starter and rotate it counterclockwise and remove it from its socket.
)NOTE:
The starters are positioned as follows: facing the unit the starter
on the left is for the lamp circuit in the rear of the unit, and as you
come forward the starter positions go to the right.
5. Install the new starter and rotate it clockwise to latch it in place.
6. Replace the diffuser panel.
SERVICE PARTS LIST
INNOVA LIGHT ASSEMBLY
PARTNO. DESCRIPTION
P0420-5180 Lamp Ballast (60 Hz only)
P0420-5190 Lamp Ballast (50 Hz only)
P0300-0042 Fluorescent Lamp
P0400-1420 Starter Fluorescent
P0380-0210 Lamp Socket
M1233-9403 Light Diffuser Assy.
P0380-3390 Fuse, 1.6 Amp

NEW BRUNSWICK SCIENTIFIC •INNOVA 4230 - LIGHT MANIFOLD 8
CONTROL SCHEMATIC
FIGURE 3