Nibe SOLAR 42 User guide

LEK
SOLAR 42
Installatörshandbok SOLAR 42
för NIBE F1145/F1345
SE
Installer manual SOLAR 42
for NIBE F1145/F1345
B
Installateurhandbuch SOLAR 42
für NIBE F1145/F1345
DE
Asentajan käsikirja SOLAR 42
NIBE F1145/F1345
FI
IHB 1218-2
031887

General
With SOLAR 42, F1145/F1345 together with:
႑VPAS can be connected to solar heating for hot water
charging.
႑VPBS (only F1145) is connected to solar heating for hot
water charging.
႑VPB/heater for hot water charging via heat exchanger.
The heat pump prioritises charging from the solar panel.
Caution
This accessory may require a program software
update in your F1145/F1345.
1031 or higher is the minimum software version
for the pump.
Caution
The water from the solar panel can reach high
temperatures. The hot water side must be sup-
plied with a mixing valve.
Contents
Cable ties4 x
Unit box (comprising AA5, FA1 and X1).1 x
Heating pipe paste2 x
Aluminium tape1 x
Insulation tape1 x
Temperature sensor (BT54), black1 x
Temperature sensor, high temp (BT53), trans-
parent
1 x
Component positions
LEK
AA5-X4
AA5-S2
AA5-X2 AA5-X9 X1
FA1
AA5-F1AA5
Electrical components
Miniature circuit-breaker. 10AFA1
Terminal block, power supplyX1
Accessory cardAA5
Terminal block, sensors and external bloc-
king
AA5-X2
Terminal block, communicationAA5-X4
Terminal block, circulation pump, mixing
valve and auxiliary relay
AA5-X9
DIP switchAA5-S2
Fine wire fuse, T4AH250VAA5-F1
Designations in component locations according to
standard IEC 81346-1 and 81346-2.
10
English, Installer manual - SOLAR 42
B

Pipe connections
Charge pump
႑Place the charge pump (GP4) on the return line to the
solar panel according to the outline diagram.
Temperature sensor
႑Sensor, solar panel (BT53) is placed in the solar panel's
submerged tube by the outlet from the solar panel.
6XEPHUJHGWXEH႑Sensor, solar coil (BT54) is positioned in submerged
tube UA3 (VPBS).
Install the temperature sensors with cable ties with heat
conducting paste.
NOTE
Sensor and communication cables must not be
placed near power cables.
NOTE
See manual for VPBS for more information.
Suitable flows/solar panel area
Recommended flow is 50 l/h per m2solar panel area.
11
B

Outline diagram
Explanation
External additional heatEB1
Expansion vessel, closedCM5
External electrical additional heatEB1
Safety valve, heating medium sideFL10
Shut-off valve, heating medium sideQM42 -
QM43
Trim valveRN11
Heat pump systemEB100
Temperature sensor, outdoorBT1
Temperature sensor, hot waterBT6
Temperature sensor, external flow lineBT25
Temperature sensor, external return lineBT71
Heat pumpEB100
Cooling module AEP14
Cooling module BEP15
Safety valve, collector sideFL10 -
FL11
Safety valve, heating medium sideFL12 -
FL13
Particle filterHQ1
HQ12 -
HQ15
Shut-off valve, brine sideQM50 -
QM53
Shut-off valve, heating medium sideQM54 -
QM57
Reversing valve, heating/hot waterQN10
Non-return valveRM10 -
RM13
SOLAR 42EP30
Accessory cardAA5
Sensor, solar panelBT53
Sensor, solar coilBT54
Pump stationGP30
Safety valve, solarFL4
Circulation pump, solarGP4
Shut-off valveQM43 -
QM45
Non-return valveRM3 -
RM4
Hot water comfortQZ1
Accessory cardAA5
Temperature sensor, hot water flowBT70
Mixer valve, hot waterFQ1
Circulation pump, domestic hot water circulationGP11
Non-return valveRM23
Trim valveRN20
Miscella-
neous
Manometer, brine sideBP6
Expansion vessel, heating medium sideCM1,
CM5
Level vesselCM2
Expansion vessel, brine sideCM3
Accumulator tank with solar coilCP10
Buffer vesselCP20
Water heater
EB10
Solar panelEP8
Ground-source heating/Ground collectorEP12
Safety valve, heating mediumFL2
Safety valve, brineFL3
Circulation pump, heating medium externalGP10,
GP18
Filler valve, brineQM12
Venting valve, brine sideQM21
Shut-off valve, heating medium flowQM31
Shut off valve, heating medium returnQM32
Shut off valve, brine returnQM33
Shut off valve, brine flowQM34
Shut-off valveQM42
Non-return valveRM21
Filling set, brineXL15
Connection, filling brineXL27 -
XL28
Designations in component locations according to
standard IEC 81346-1 and 81346-2.
12
B

Outline diagram F1145 with VPBS and SOLAR 42
-QM31
-QM3
-FL3
-QM4
-QM1
-CM
-HQ1
-XL15
-EB100
F1145
-EB100-BT1
-QM34
-FL
-CM1
-EB100
-EB100-BT6
-CP10
-EP30-BT53
-EP8
-AA5
-EP30 -CM5
-GP4
-QM45
-RM3
-QM43
-QM44
TP
-FL4
-RM4 T
-GP30
-EP30
-BT54
-EP1
Outline diagram F1345 with VPAS and SOLAR 42
-BT6
- B100
-CP10
- B100-BT71
- P12
-CM3
P
-BP6-QM21 -FL3
-XL28-XL27
-QM33
-QM34
- B100-BT1
- B100-BT25
-HQ15
-HQ14
-RM12
-RM13
-QM54
-FL12
-QM55
-QM56
-QM57
-FL13
-HQ13
-RM11
-HQ12
-RM10-QM50
-QM51
-FL10
-QM52
-QM53
-FL11
- B100
- P15
- P14
- B100
-CM5
- P30-BT53
- P8
-GP4
-QM45
-RM3
-QM43
-QM44
T P
-FL4
-RM4 T
-GP30
-BT54
- P30
- P30-AA5
- B100-QN10
-QZ1-AA5
-GP11
-RN20
-RM23
- B10
-FQ1 -BT70
-QZ1
-CM5 -FL10
-QM42
-QM43-RN11
- B1
- B1
-RM21
-GP18
-CP20
-GP10
13
B

Electrical connection
NOTE
All electrical connections must be carried out by
an authorised electrician.
Electrical installation and wiring must be carried
out in accordance with the stipulations in force.
The heat pump must not be powered when in-
stalling SOLAR 42.
The electrical circuit diagram is at the end of this Installer
handbook.
Connecting the supply
Connect the power supply to terminal block X1 as illus-
trated.
3
2
1N
230V 50Hz-X1
L
P
8QLWER[([WHUQDO
Connecting communication
This accessory contains an accessory card (AA5) that must
be connected directly to the heat pump on the input card
(terminal block AA3-X4) in F1145 or on terminal block
X6 in F1345.
If several accessories are to be connected or are already
installed, the following instructions must be followed.
The first accessory card must be connected directly to the
input card's terminal block (AA3-X4) in F1145 or on ter-
minal block X6 on F1345. The following cards must be
connected in series with the previous card.
Use cable type LiYY, EKKX or similar.
1
2
3
4
5
6
7
8
AA5-X4
15
A
B
GND
A
B
GND
A
B
GND
A
B
GND
A
B
GND
14
13
AA3-X4
1
2
3
4
5
6
7
8
AA5-X4
X6
1 2 3 4
A
B
GND )
$$;
ON
1 2 3 4 5 6 7 8
-X9
-X2
24 20212223 1516171819 1011121314 56789 1
1
N
L
PE
PE
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
9
234
-X8
-X4
-X10
-X1
$$;
ON
1 2 3 4 5 6 7 8
-X9
-X2
24 20212223 1516171819 1011121314 56789 1
1
N
L
PE
PE
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
9
234
-X8
-X4
-X10
-X1
$$;
LEK
)$FFHVVRU\FDUG$FFHVVRU\FDUG(%;14
B

ON
1 2 3 4 5 6 7 8
-X9
-X2
24 20212223 1516171819 1011121314 56789 1
1
N
L
PE
PE
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
9
234
-X8
-X4
-X10
-X1
$$;$$;Caution
The relay outputs on the accessory card can have
a max load of 2 A (230 V) in total.
Connecting sensors
Use cable type LiYY, EKKX or similar.
Sensor, solar panel (BT53)
Connect the sensor (solar panel) to AA5-X2:23-24.
Caution
Sensor cable splicing must fulfil IP54.
Sensor, solar coil (BT54)
Connect the sensor (solar coil) to AA5-X2:21-22.
24 20212223 1516171819 1314
%7%7$$;([WHUQDO8QLWER[
Connection of the circulation pump (GP4)
Connect the circulation pump (GP4) to AA5-X9:2 (230
V), AA5-X9:1 (N) and X1:3 (PE).
1
2
3
4
L
N
P
3
2
1
Unit box External
AA5-X9
GP4
X1
Connecting solar panel cooling
Connect solar panel cooling (if applicable) to AA5-X9:3
(N) and AA5-X9:4 (230 V).
1
2
3
4
5
6
7
8
96RODUSDQHOFRROLQJ1/$$;8QLWER[([WHUQDO
DIP switch
The DIP switch on the accessory card must be set as fol-
lows.
ON
1 2 3 4 5 6 7 8
$$6
ON
12345678
-X9
-X2
24 20212223 1516171819 1011121314 56789 1
1
N
L
PE
PE
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
9
234
-X8
-X4
-X10
-X1
15
B

Program settings
Program setting of SOLAR 42 can be performed via the
start guide or directly in the menu system.
Caution
Also see the Installer manual for F1145/F1345.
Caution
This accessory may require a program software
update in your F1145/F1345.
1031 or higher is the minimum software version
for the pump.
Start guide
The start guide appears upon first start-up after heat
pump installation, but is also found in menu 5.7.
Menu system
If you do not make all settings via the start guide or need
to change any of the settings, this can be done in the
menu system.
Menu 5.2 - system settings1)
Activating/deactivating of accessories.
Select: solar heating
1) Applies to NIBE F1145.
Menu 5.2.4 - accessories2)
Activating/deactivating of accessories.
Select: solar heating
2) Applies to NIBE F1345.
Menu 5.3.4 - solar heating
Settings for solar heating.
Menu 5.6 - forced control
Forced control of the different components in the heat
pump as well as in the different accessories that may be
connected.
EP30-AA5-K1: Activating the circulation pump (GP4).
EP30-AA5-K2: Activating solar panel cooling.
EP30-AA5-K3: Signal to three way valve (QN23).
EP30-AA5-K4: No function.
16
B