No Butts Bin SR1601-F User manual

Assembly Instructions
SR1601-F-02-14022019-USA
Shelter Type: SR1601-F
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]

13
2
1
15
16
8
12
11
10
6
4
3
14
7
59
2
EXPLODED VIEW
Spanner
Torx bit
Tools required:
Drill/Screwdriver
Mallet
Hack saw
ITEM
NO. PART NAME
DRG NUMBER LENGTH
Default/QT
Y.
1 S1C Frame S1C
No Plastics
2
2 Frame S3C
Default
2
3 JF1 Bracket JF1
Default
2
4 CB1 Bracket CB1
Default
4
5 RB1 Bracket RB1
Default
4
6 Rafter R3
Default
3
7 L3 Bracket L3
Default
2
8 L1 Bracket L1
Default
4
9 Beam B1
Default
1
10 Sealing Strip SS
Default
4
11 PCE1 Roof Sheet PCE1
Default
2
12 RC1 Roof Strip RC1
Default
3
13 2MD Roof Edging 2MD
2110 2
14 FT1 Bracket FT1
Default
2
15 FT3 Bracket FT3
Default
3
16 40x40 End cap BOUGHT IN ITEM
40 x 40 x
20 5

PARTS LIST
3
Fittings Bolt set M10
Nut Washer
Black
Cap
T25 T38 AB1210
M10 x 60
25mm
Tech
screw
38mm
Tech
screw
M10 x 100
Concrete Bolt
Pack A
30 30 60 60 72 30 8
Required 22 22 49 49 32 18 5
Image
ITEM NO. PART NO. DESCRIPTION DIMENSION (MM) DIMENSION (INCH) IMAGE QTY.
1 S1C FRAME 2000x1035 78.74x40.55 2
2 S3C FRAME 2000x517 78.74x20.35 2
3 JF1 BRACKET 220x40 8.66x1.58 2
4 CB1 BRACKET 110x110 4.33x4.33 4
5 RB1 BRACKET 110x40x40 4.33x1.81 4
6 R3 RAFTER 1035x40x40 40.75x1.57x1.57 3
7 L3 BRACKET 73x38 2.87x1.50 2
8 L1 BRACKET 95x45 3.74x1.77 4
9 B1 BEAM 2100x40x40 82.68x1.57x1.57 1
10 SS SEALING STRIP TRIM TO SUIT TRIM TO SUIT 1 Roll
11 PCE1 ROOF PANEL 1130x1050 44.49x41.34 2
12 RC1 ROOF STRIP 1130 44.49 3
13 2MD ROOF EDGE TRIM TO SUIT TRIM TO SUIT 3
14 FT1 FOOT BRACKET 109x100x40 4.29x3.93x1.57 2
15 FT3 FOOT BRACKET 109x100x80 4.29x3.93x3.27 3
16 EC40 END CAP 40x40 1.57x1.57 10

ENSURE CORRECT
ALIGNMENT ON
BOTH SIDES
4
ENSURE CORRECT
ALIGNMENT ON
BOTH SIDES
517
2110
557
20.35
83.07
21.93
Check dimensions to ensure
correct alignment
S1C
S3C
FT1
FT3
FT3
FT1
CB1
JF1
JF1
CB1
Step 1
Assemble main frame using S1C and S3C welded Frames. Join the frames
using CB1 brackets in the corners and JF1 brackets for the flat joints.
Then move the shelter to its final position, attach FT1 and FT3 foot brackets
and use the concrete bolts to secure it to the ground.
MEASUREMENTS IN BLUE - MM
MEASUREMENTS IN GREEN - INCHES

RB1
RB1RB1
RB1
L3
L3
R3
R3
R3
5
RB1
RB1RB1
RB1
R3
R3
R3
L3
Step 2
Attach R3 rafters using RB1 brackets at rear and L3 brackets in
the centre.

Step 3
Attach L1 brackets to R3 rafters. Then attach B1 tie bar.
L1
L1L1
L1
R3
B1
6
L1
L1
L1
B1
L1

RC1
PCE1
PCE1
2MD
2MD
SS
7
PCE1
PCE1
RC1
RC1
RC1
2MD
2MD
Step 4
Apply sealing strips to R3 rafters then put the PCE1 Panels on top,
secure down RC1 strips with 38mm Tech screws . Then attach the
2MD edge trim.
NOTE: Sealing Strip
to be attached to
rafters as below.

2193 HOLE CENTERS ON FEET
477
2110
1035
86.34
20.73
526.50
18.78
40.75
83.07
44.90
1140.56
PLAN VIEW
Suggested size for concrete base: 200mm / 7.87in
oversized on all four sides
8

Notes:
9

Notes:
10