TMG TMG-ST3040C User manual

►www.tmgindustrial.com 0/12 TOLL FREE:1-877-761-2819

►www.tmgindustrial.com 1/12 TOLL FREE:1-877-761-2819
MAIN SPECIFICATIONS :
Overall assembled size : W9.15 x L12 x H2.2 (m) / 30 x 39.37 x 7.22 (ft)
Ridge Peak Height : 2.2 m / 7.22ft + container height
PRIOR TO ASSEMBLY
Please read the instructions carefully before installation. It is very important to follow your local safety regulations and
industry standards during installation. Regulations may include but are not limited to:
 Safety helmets, protective eyewear, and clothing
 Safety harnesses for all elevated workers
 Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part number, please refer to the parts list
to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not make any alterations to the structure.
Do not hang any weights on the frame during installation, including parts. We are not responsible for any damages or
injuries caused by inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to tape or add foam/rubber on the frame where joints connect and where it touches the cover. This
will help extend the life span of the cover.
Read the following item list carefully and count the number of items to ensure that all parts are included prior to setup.
STEP 1 : REVIEW THE WHOLE STRUCTURE AND CHOOSE THE PROPER INSTALLATION SITE.
Choose a solid flat level ground area to set up the building. Do not install the building on soft ground, wetland, uneven
surfaces, sloped surfaces, or on top of structures that are not rated to hold its weight.
We strongly recommend that you put the containers on hard foundations before installing the shelter.
Be aware of the surrounding area. Do not set up the building near snowdrifts, open flames or exposed electrical wires. Do
not keep heat sources near the fabric cover. Keep the building surroundings clear at all times.

►www.tmgindustrial.com 2/12 TOLL FREE:1-877-761-2819
TMG-ST3040C PART LIST
NO.
PICTURE
DESCRIPTION
LENGTH
QTY
1
Peak arch tube
L1910mm
9
2
Middle rafter tube
L2160mm
18
3
Shoulder tube
L2168mm
10
3A
Shoulder tube
L2168mm
8
4
Middle truss baseplate
W150xL200mm
14
4L
Left corner baseplate
(front and rear truss)
W150xL200mm
2
4R
Right corner baseplate
(front and rear truss)
W150xL200mm
2
5
Roof purlin
(horizontal tube)
L1438mm
40
5A
Middle truss connectors
W50xL180mm
70
5B
Front and rear connectors
W50xL121mm
10
5C
Self-tapping screws
#12x25mm
45
6
Ceiling cross bar
L2190mm
9
7
Sidewall frame steel tension
cables
L1700mm
8
7A
Ratchet
2T
18
7B
Tie down straps
W38xL800mm
18
8
Mounting base
W40xL100mm
8

►www.tmgindustrial.com 3/12 TOLL FREE:1-877-761-2819
9
Top cover tension tube
(for both bottom sides)
L1993mm
12
9A
Top cover tension tube
L500mm
2
11
Bolt
M8x70mm
108
11A
Bolt
M8x60mm
80
12
Hex bolt
M10x30mm
18
13
Top cover
L11664xW12610mm
1
14
Braided rope
φ8x60m
1
15
Scratch resistant tape
10m
2
16
Water plug
Φ32
4

►www.tmgindustrial.com 4/12 TOLL FREE:1-877-761-2819
STEP 2 : BASEPLATE POSIT INSTALLATION.
Place the containers making sure they are parallel and the correct width apart. Make sure there is a gap of about 3 feet
around the building. the center point of the round pipe of the base is the reference point, and the diagonal X and Y must
be equal. The base plate shall be welded to the top of the container on the same horizontal plane to ensure that the
welding is firm and reliable.
NO.
PART
QTY
4
14
4L
2
4R
2

►www.tmgindustrial.com 5/12 TOLL FREE:1-877-761-2819
STEP 3 : CONNECT ALL TRUSSES.
Front and rear trusses (4 trusses).
NO.
PART
QTY
NO.
PART
QTY
1
1x4
6
1x4
2
2x4
11
8x4
3A
2X4
12
2x4

►www.tmgindustrial.com 6/12 TOLL FREE:1-877-761-2819
Middle trusses (5 trusses).
NO.
PART
QTY
NO.
PART
QTY
1
1x5
6
1x5
2
2x5
11
8x5
3
2X5
12
2x5

►www.tmgindustrial.com 7/12 TOLL FREE:1-877-761-2819
Lay down all (9) trusses on the ground when the assembly is all completed and before moving to next step, and then
wrap (#15) around the sharp points of the joint to avoid friction between the fabric and the interface, resulting in fabric
damage.
NO.
PART
QTY
15
2

►www.tmgindustrial.com 8/12 TOLL FREE:1-877-761-2819
STEP 4 : PUT UP ALL TRUSSES.
Install each truss on the base tube. Use hex bolt (#11) to secure the truss to the base tube firmly. We recommend to use
a crane or forklift to lift the truss and have 2 to 3 people on site to work together. Please make sure it is safe and secure
when installation is proceeding.
NO.
PART
QTY
11
36

►www.tmgindustrial.com 9/12 TOLL FREE:1-877-761-2819
STEP 5 : CONNECT ALL PURLINS (#5) WITH BOLT (#11A). TENSION CABLE INSTALLATION .
NO.
PART
QTY
NO.
PART
QTY
5
40
7
8
5A
70
8
8
5B
10
11A
80
5C
45

►www.tmgindustrial.com 10/12 TOLL FREE:1-877-761-2819
OVERALL STRUCTURAL INSPECTION :
Check all components and trusses to ensure the entire structure is rectangular as specified in. All trusses must be 90
degrees straight up from the container.
Secure and tighten all bolts and nuts on this step. But do not over tie! Otherwise you might damage the tubes or
components.
STEP 6 : INSTALL THE TOP COVER (#13) STRETCH AND TIGHTEN TOP COVER.
DO NOT INSTALL THE COVER DURING WINDY WEATHER!
Stretch and adjust the cover from back and forth, to make sure it is square and centered.
Unpack the top cover and place it along one of the long sides of the structure.
Use 3 to 5 ropes to pull the cover over the top of the structure, from the inside 2 or 3 people standing inside
on ladders to push upwards will help to move the cover without any damage.
13

►www.tmgindustrial.com 11/12 TOLL FREE:1-877-761-2819
 After the cover is installed on the roof, then insert tension tubes (#9,#9A) in the groove on both sides of the cover
bottom, Add the water plug (#16) on the 1st tube (#9) to protect the fabric while the tube is going through and add
the water plug on the last tube also to keep water away.
 Stretch and adjust the cover from left and right, back and forth, to make sure it is square and centered. Cut the
grooves from inner side facing to the ratchet hardware (#7A), and add tie down straps (#7B) to pull the tension tube
and tie the strap to the base.
 Starting from the center point of the frame (highest ridge point) use ropes (#14) through the grommets to tie the
panel to the truss firmly. All grommets need to be tied to the frame as shown.
NO.
PART
QTY
ROPE SHEAR SIZE
7A
18
14
QTY
7B
18
14
10000mm
4
9
12
9A
2
16
4

►www.tmgindustrial.com 12/12 TOLL FREE:1-877-761-2819
AFTER INSTALLATION.
Walk around and inspect the building periodically to make sure the parts are firmly fixed and the whole building is well
supported. Check all bolts and hardware connectors to make sure they are in place and tightened. Check the base plates,
adjust the ropes if necessary and clean the cover regularly.
Snow accumulating on the fabric cover must be removed as soon as possible. If snow is allowed to become solid ice on
the cover, it could increase the weight on the roof and collapse the building or reduce the life span.
We strongly recommend you remove any snow from the roof immediately. Do not leave any snow load on the roof
overnight. Keep 3 feet of clearance on all sides at all times. Do not allow snow to accumulate and pile up on the sides of
the building. Otherwise the pressure from the sides will push inwards and could lead to a collapse.