No Butts Bin SR1553-F User manual

Assembly Instructions
Product code: SR1553-F
Doc. No.:
SR1553-F-01-130219-USA
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]

1
5
4
13
10
9
11
6
7
8
12
2
3
EXPLODED VIEW AND TOOLS
2
Tools required:
Drill/Screwdriver
Mallet
Hack saw
Spanner
Torx bit
ITEM
NO. PART NAME
DRG NUMBER LENGTH
Default/QT
Y.
1 S1C Frame S1C
Default
8
2 CB1 Bracket CB1
Default
8
3 JF1 Bracket JF1
Default
9
4 FT1 Bracket FT1
Default
2
5 FT3 Bracket FT3
Default
7
6 RB1 Bracket RB1
Default
16
7 R1 Rafter R1
Default
5
8 Sealing Strip SS
Default
8
9 PCE1 Roof Sheet RC1
Default
2
10 PCC1 Roof Sheet PCE1
Default
2
11 RC1 Roof Strip 2MD
Default
5
12 ST3 Roof Tie ST3
Default
1
13 2MD Roof Edging B1
2110 4
14 40x40 End cap BOUGHT IN ITEM
40 x 40 x
20 12

3
PARTS LIST AND FITTINGS
Fittings Bolt set M10 T25 T38 AB1210
M10 x 60mm Nut Washer
Black
Cap
25 mm
Tech
screw
38 mm
Tech
screw
M10/12 x 100
mm Concrete
Bolt
Pack A+B 40 40 80 80 136 66 13
Required 19 19 38 38 100 30 9
Image
ITEM NO. PART NO. DESCRIPTION DIMENSION (MM) DIMENSION (INCH) IMAGE QTY.
1 S1C Frame 2000x1035 78.74x40.75 8
2 CB1 Bracket 110x110 4.33x4.33 8
3 JF1 Bracket 220x40 7.87x1.58 9
4 FT1 Bracket 109x100x40 4.29x3.94x1.58 2
5 FT3 Bracket 109x100x80 4.29x3.94x3.15 7
6 RB1 Bracket 110x42x40 4.33x1.81 16
7 R1 Rafter 1130x40x40 44.49x1.58x1.58 5
8 SS Sealing Strip Trim To 1135 TRIM TO 44.69 2 ROLLS
9 PCE1 Roof Panel 1050 x 1150 41.34x45.28 2
10 PCC1 Roof Panel 1030X1150 40.55x45.28 2
11 RC1 Roof Strip 1130 44.49 5
12 ST3 Roof Tie 2060x40x40 88.98x1.58x1.58 1
13 2MD Roof Edge Trim Trim To Suit 5
14 EC40
Plastic
End Cap
40x40 1.58x1.58 18

4180
1075
1075
42.32
164.57
42.32
A
Check overall dimensions
to ensure correct alignment
Please note 38mm Tec Screws
are for roof panels only
CB1
JF1
S1C FRAME
ST3
NOTE: Insert EC40 into
ST3 before installing.
DETAIL A
SCALE 1 : 7
CB1 UNDERNEATH
JF1 ON INNER
ST3 TIE BAR
CB1CB1CB1CB1
Ensure correct
alignement on all corners
Step 1
Assemble S1C frames to make up the main structure using CB1 brackets
for the corners and JF1 brackets for straight joints. Also use CB1 and JF1
brackets to secure the ST3 tie bar.
4
BLUE DIMENSIONS - MM
GREEN DIMENSIONS - INCH

RB1
R1
3.
1035 1035
C
FT3 FT1
1.
RB1
R1
995
39.17
1035 1035 1035 1035
40.75 40.75 40.75 40.75
SCALE 1 : 30
Step 2
Move the Shelter to its final position and attach all FT1 and FT3 foot brackets.
Attach the RB1 Brackets to the top of the frames and bolt the R1 rafters
through the brackets.
5
2.

SS
PCE1
PCE1
PCC1
PCC1
PCE1
PCE1
PCC1
PCC1
SS
Step 3
Apply sealing strips (SS) to the top of the rafters then arange the roof panels by
lining up the end panels( PCE1 ) flush with the rafters and leaving a gap between
the middle pieces( PCC1 ).
6

RC1
2MD
RC1
2MD
Step 4
Secure the roof panels in place by drilling the RC1 strips directly
into the frame of the shelter using the 38mm screws. Then
apply the 2MD edge trim along the bottom edges of the roof,
tapping them on with a mallet. Push the small black caps onto any
exposed nut or bolt.
7
GENERAL NOTE:
THE 38mm TECH SCREWS
ARE FOR FIXING ROOF
STRIPS(RC) ONLY

995
1056.50
2171.50 1035 1044.50
1044.50
1035 1035 1035
1135.63
4180 OR 164.57
4251 OR 167.36 TO FOOT HOLE CENTERS
41.12 40.75 85.49
44.71
39.17
41.12 40.75 40.75 40.75
41.12
8
GROUND ANCHOR POSITIONS AND OVERALL SIZE
SUGESTED SIZE FOR BASE: 200mm OR 7.87Inch OVERSIZES ON ALL 4 SIDES
Scale 1:20

Notes:
9

Notes:
10