NordicTrack NTEVEL19016.2 User manual

USER’S MANUAL
Model No. NTEVEL19016.2
Serial No.
Write the serial number in the space
above for reference.
CAUTION
Read all precautions and
instructions in this manual before
using this equipment. Keep this
manual for future reference.
Serial
Number
Decal
www.iconeurope.com
CUSTOMER SERVICE
UNITED KINGDOM
Call: 0330 123 1045
From Ireland: 053 92 36102
Website: www.iconsupport.eu
E-mail: [email protected]
Write:
ICON Health & Fitness, Ltd.
Unit 4, Westgate Court
Silkwood Park
OSSETT
WF5 9TT
UNITED KINGDOM
AUSTRALIA
Call: 1800 993 770
E-mail: [email protected]
Write:
ICON Health & Fitness
PO Box 635
WINSTON HILLS NSW 2153
AUSTRALIA

2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning
decal(s). If a decal is missing or illegible, see
the front cover of this manual and request a
free replacement decal. Apply the decal in the
location shown. Note: The decal(s) may not be
shown at actual size.
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS..................................................................3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
THE CHEST HEART RATE MONITOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
HOW TO USE THE ELLIPTICAL ..............................................................11
MAINTENANCE AND TROUBLESHOOTING.....................................................25
EXERCISE GUIDELINES ....................................................................27
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
ORDERING REPLACEMENT PARTS .................................................. Back Cover
RECYCLING INFORMATION ......................................................... Back Cover
NORDICTRACK and IFIT are registered trademarks of ICON Health & Fitness, Inc. The BLUETOOTH®word
mark and logos are registered trademarks of Bluetooth SIG, Inc. and are used under license. Google Maps is a
trademark of Google Inc. Wi-Fi is a registered trademark of Wi-Fi Alliance. WPA and WPA2 are trademarks of
Wi-Fi Alliance.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical before using your elliptical. ICON
assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. It is the responsibility of the owner to ensure
that all users of the elliptical are adequately
informed of all precautions.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
3. The elliptical is not intended for use by
persons with reduced physical, sensory, or
mental capabilities or lack of experience and
knowledge, unless they are given supervi-
sion or instruction about use of the elliptical
by someone responsible for their safety.
4. Use the elliptical only as described in this
manual.
5. The elliptical is intended for home use only.
Do not use the elliptical in a commercial,
rental, or institutional setting.
6. Keep the elliptical indoors, away from mois-
ture and dust. Do not put the elliptical in a
garage or covered patio, or near water.
7. Place the elliptical on a level surface, with at
least 4 ft. (1.2 m) of clearance in the front of
the elliptical, 6 ft. (1.8 m) in the rear, and 2 ft.
(0.6 m) on each side. To protect the floor or
carpet from damage, place a mat under the
elliptical.
8. Inspect and properly tighten all parts each
time the elliptical is used. Replace any worn
parts immediately.
9. Keep children under age 13 and pets away
from the elliptical at all times.
10. The elliptical should not be used by persons
weighing more than 330 lbs. (150 kg).
11. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical. Always wear athletic
shoes for foot protection while exercising.
12. Hold the handlebars when mounting, dis-
mounting, or using the elliptical.
13. The heart rate monitor is not a medical
device. Various factors may affect the accu-
racy of heart rate readings. The heart rate
monitor is intended only as an exercise aid
in determining heart rate trends in general.
14. The elliptical does not have a freewheel; the
pedals will continue to move until the fly-
wheel stops. Reduce your pedaling speed in
a controlled way.
15. Keep your back straight while using the ellip-
tical; do not arch your back.
16. Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.
IMPORTANT PRECAUTIONS

4
Thank you for selecting the revolutionary
NORDICTRACK®FREESTRIDE TRAINER FS7I
elliptical. The FREESTRIDE TRAINER FS7I elliptical
provides an impressive selection of features designed
to make your workouts at home more effective and
enjoyable.
For your benefit, read this manual carefully before
you use the elliptical. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Handlebar
Fan
Handle
Accessory Tray
Console
BEFORE YOU BEGIN
Wheel
Leveling Foot
Length: 5 ft. 2 in. (157 cm)
Width: 2 ft. 5 in. (74 cm)
Weight: 282 lbs. (128 kg)
Incline Control
Resistance Control
Pedal

5
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.
M8 x 68mm Screw
(125)–2
M4 x 16mm
Screw (98)–7
M8 x 14mm
Shoulder
Screw (112)–2
M4 x 10mm
Screw (128)–1
M8 Locknut
(123)–4
Pedal Arm Washer (89)–2
M8 x 45mm Bolt
(124)–4
M6 x 16mm
Screw
(111)–6

6
2. With the help of a second person, raise the
Upright (2) to the vertical position.
While a second person holds the Upright (2),
attach the Upper Pillar (47) to the Lower Pillar
(48) with two M8 x 45mm Bolts (124) and two
M8 Locknuts (123); start both Bolts, and then
tighten them. Make sure that the indicated
Locknut is in the hexagonal hole (A).
2
124
123
48
2
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish all assembly steps.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
• To identify small parts, see page 5.
• In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver
two adjustable wrenches
one rubber mallet
Assembly may be easier if you have a set of
wrenches. To avoid damaging parts, do not use
power tools.
ASSEMBLY
1
47
124
A
123
1. Go to www.iconsupport.eu on your computer
and register your product.
• activates your warranty
• saves you time if you ever need to contact
Customer Service
• allows us to notify you of upgrades and offers
Note: If you do not have internet access, call
Customer Service (see the front cover of this
manual) and register your product.

7
3. Attach the Left Large Slot Cover (22) to the
Left Inner and Outer Shields (27, 28) with two
M4 x 16mm Screws (98).
Attach the Right Large Slot Cover (142) to the
Right Inner and Outer Shields (21, 23) in the
same way.
4. Attach Pillar Covers A and B (29, 30) around
the Lower Pillar (48) with two M4 x 16mm
Screws (98).
3
4
98
98
29 48
30
142
21, 23
22
27, 28
98
5
5. Press the Upper Pillar Cover (26) onto the Left
Inner and Outer Shields (27, 28).
Attach the Upper Pillar Cover (26) with an
M4 x 10mm Screw (128).
128
26
27, 28

8
7. See the inset drawing. Loosen the indicated
M8 x 45mm Bolt (124).
Next, rotate the Right Upper Body Arm (7) into
the vertical position.
Secure the Right Upper Body Arm (7) to the
Right Leg (5) with an M8 x 45mm Bolt (124) and
an M8 Locknut (123).
IMPORTANT: See the inset drawing. Tighten
the indicated M8 x 45mm Bolt (124).
Tip: Avoid pinching the wires (not shown).
Slide the Right Leg Cover B (36) downward and
press it into place.
Repeat this step on the other side of the
elliptical.
124
123
7
5
36
7
Avoid pinching
the wires
124
133
89
6
6. Identify the Left Pedal Arm (9). Using a plastic
bag to keep your fingers clean, apply a generous
amount of the included grease to the axle on the
Left Pedal Arm.
Then, insert the Left Pedal Arm (9) into the Left
Leg (6).
Attach the Left Pedal Arm (9) with an
M8 x 14mm Shoulder Screw (112), an
Outer Pedal Cover (133), and a Pedal Arm
Washer (89).
Attach the Right Pedal Arm (132) to the Right
Leg (5) in the same way.
9
132
5
112
Grease 6

9
9
8
9. Tip: Avoid pinching the wires. Insert the
Console Bracket (3) into the Upright (2). Attach
the Console Bracket with two M8 x 68mm
Screws (125).
Then, connect the wires from the Console
(4) to the Main Wire (141), the Right and Left
Control Wires (12, 13), and the Accelerometer
Wire (138).
8. Route the right Strap (119) under the right Roller
(67); make sure that the Strap is not twisted
and that it is routed under the Roller.
Attach the right Strap (119) to the right rear Glide
Belt Cover (63) with three M6 x 16mm Screws
(111) and a Strap Clamp (64); start all the
Screws, and then tighten them.
Repeat this step on the other side of the
elliptical.
10. Tip: Avoid pinching the wires. Attach the
Upper Neck Cover (17) to the Upper Bridge
Cover (16) with an M4 x 16mm Screw (98).
4
125
98 17
16
3
2141
12
111
63
64
119
Avoid
pinching
the wires
Avoid pinching
the wires
125
13
138
10
11. Make sure that all parts are properly tightened before you use the elliptical. Extra parts may be included.
Place a mat beneath the elliptical to protect the floor.
67

10
THE CHEST HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
If the heart rate monitor looks like the one shown
in drawing 1, press the transmitter (A) onto the snap
fasteners on the chest strap (B). If the heart rate
monitor looks like the one shown in drawing 2,
insert the tab (C) on one end of the chest strap (D) into
one end of the transmitter (E). Then, press the end of
the transmitter under the buckle (F) on the chest strap;
the tab should be flush with the transmitter.
Next, wrap the heart
rate monitor around
your chest in the loca-
tion shown; the heart
rate monitor must be
under your clothes,
tight against your skin.
Make sure that the logo
is right-side-up. Then, attach the other end of the chest
strap. Adjust the length of the chest strap, if necessary.
Next, pull the trans-
mitter and the chest
strap away from your
body a few inches
and locate the two
electrode areas (G).
Using saliva or con-
tact lens solution, wet the electrode areas. Then, return
the transmitter and the chest strap to a position against
your chest.
CARE AND MAINTENANCE
• Thoroughly dry the electrode areas with a soft towel
after each use. Moisture may keep the heart rate
monitor activated, shortening the life of the battery.
• Store the heart rate monitor in a warm, dry place. Do
not store the heart rate monitor in a plastic bag or
other container that may trap moisture.
• Do not expose the heart rate monitor to direct
sunlight for extended periods of time, and do not
expose it to temperatures above 122°F (50°C) or
below 14°F (-10°C).
• Do not excessively bend or stretch the heart rate
monitor when using or storing it.
• To clean the transmitter, use a damp cloth and a
small amount of mild soap. Then, wipe the transmit-
ter with a damp cloth and thoroughly dry it with a soft
towel. Never use alcohol, abrasives, or chemicals
to clean the transmitter. Hand wash and air dry the
chest strap.
TROUBLESHOOTING
• If the heart rate monitor does not function when
positioned as described at the left, move it slightly
lower or higher on your chest.
• If heart rate readings are not displayed until you
begin perspiring, re-wet the electrode areas.
• For the console to display heart rate readings, you
must be within arm’s length of the console.
• If there is a battery cover on the back of the trans-
mitter, replace the battery with a new battery of the
same type.
• The heart rate monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical condi-
tions such as premature ventricular contractions
(pvcs), tachycardia bursts, and arrhythmia.
• The operation of the heart rate monitor can be
affected by magnetic interference from high power
lines or other sources. If you suspect that magnetic
interference is causing a problem, try relocating the
fitness equipment.
1 2
A
B
EF
CD
G