Nortel BSG12aw/ew/tw User manual

BSG8ew and BSG12aw/ew/tw 1.0
Business Services Gateway
Document Status:Standard
Document Number:NN47928-105
Document Version: 01.03
Date: July 2008
Quick Start Guide

Copyright © 2008 Nortel Networks, All Rights Reserved
All rights reserved.
The information in this document is subject to change without notice. The statements, configurations, technical data, and
recommendations in this document are believed to be accurate and reliable, but are presented without express or implied
warranty. Users must take full responsibility for their applications of any products specified in this document. The
information in this document is proprietary to Nortel Networks.
Trademarks
Nortel, the Nortel logo, and the Globemark are trademarks of Nortel Networks.
All other trademarks and registered trademarks are the property of their respective owners.

3
Quick Start Guide
Quick Start Wizard
Use this guide to complete the basic configuration of the Business Services Gateway
(BSG) and to enable remote access configuration.
You will need the following information from your ISP or network administrator to
complete the Wizard:
Login
information
Value
IP address of
the device
default:192.168.1.1
Username default:nnadmin
Password default:PlsChgMe!
WAN
BSGew BSGtw BSGaw
Interface Interface type DSL Name
Encapsulation
mode
Ethernet Interface DSL
Connection
Type
PPPoE Framing ESF
SF
VPI/VCI
Authentication
Required
ISP (PPPoE) Name Clock source Loop Timing
Local Timing
User Name
Password
User name Time slot
Password Authentication
required
User name
Password
Host name
MAC Cloning Enable
Disable
MAC Address
IP Address
Assignment
Manual
Dynamic
WAN IP
address
Subnet Mask

4
NN47928-105
Gateway IP
Address
Primary DNS
Secondary
DNS
LAN
LAN IP address Do not change
LAN subnet
mask Do not change
DHCP Setup Server
Relay
None
DHCP Server
configuration
IP Pool Starting Address
IP Pool End Address
Wireless
Country Code
Wifi Security
selection
Open System
WPA-PSK
WPA2-PSK
WEP select key size- 64, 128, 152
Security Key
SIP Phone connection
SIP host
domain
SIP central
server
Maximum
Simultaneous
calls per WAN
link
WAN port
number of permitted calls

5
Quick Start Guide
Remote Access
Procedure
1Ensure that the BSG is powered up and connected to the Internet.
2Connect a PC to the LAN port of the BSG.
3Open a web browser.
4In the address bar of the browser, enter the LAN IP address of BSG and press Enter.
Remote Access
Enable remote
access
Telnet
SSH

6
NN47928-105
5The BSG login page appears.
6Enter the user name and password and click the login button to access the device.
The system information panel appears.

7
Quick Start Guide
7In the navigation panel on the left, click on the Quick Start Wizard option.
The Quick Start Wizard opens.
8Click on the arrow in the middle of the page to continue.
The Setting Up Your WAN configuration panel appears. The fields on your panel will be
different depending on which model of BSG you are configuring. Select the appropriate model
below:
•BSGtw (page 8)
•BSGew (page 9)
•BSGaw (page 10)

8
NN47928-105
BSGtw
aSelect the interface from the drop down list.
bSelect the Framing.
cSelect the Clock Source.
dEnter the Time Slot.
eSelect whether Authentication is Required.
fIf authentication is required enter the username and password.
gOnce you have finished entering the information click on the Apply button at the
bottom of the panel.
hClick Next.
The Setting Up Your LAN configuration panel appears.

9
Quick Start Guide
BSGew
aSelect the interface from the drop down list.
bSelect the Encapsulation mode.
cOnce you have finished entering the information click on the Apply button at the
bottom of the panel.
dClick Next.
The Setting Up Your LAN configuration panel appears.
PPPoE Ethernet
1. Enter ISP name 1. Select whether to enable or disable the MAC
Cloning.
2. Enter the user name 2. If MAC cloning is enabled enter the MAC
address.
3. Enter the password 3. Select whether IP address assignment is
manual or dynamic
4. Enter the Host Name. 4. If the IP address assignment is manual enter
the:
- WAN IP address
- Subnet Mask
- Gateway IP Address
- Primary DNS
- Secondary DNS

10
NN47928-105
BSGaw
aSelect the DSL Name.
bSelect the DSL Connection Type.
cEnter the VPI/VCI.
dSelect whether Authentication is Required.
eEnter the username.
fEnter the password.
gOnce you have finished entering the information click on the Apply button at the
bottom of the panel.
hClick Next.
The Setting Up Your LAN configuration panel appears.
9Enter all of the parameters identified by your administrator at the beginning of this guide.
10 Once you have finished entering the information click on Apply to save the configuration.

11
Quick Start Guide
11 Click the Next button at the bottom of the panel to advance to the next panel.
The Setting up your Wireless configuration panel appears.
12 Select the Country Code.
13 Refer to the information at the beginning of this guide for the correct security settings to enter.
14 Click on Apply to save the configuration.
15 Click the Next button at the bottom of the panel to advance to the next panel.
The Setting up Your SIP Phone Connection configuration panel appears.
16 Enter the SIP Host Domain.
17 Enter the SIP Central Server address.
18 Enter the maximum number of Simultaneous Calls permitted across the selected WAN
interface.
19 Click on the Apply button to save the configuration.
20 Click on the Next button at the bottom of the panel.

12
NN47928-105
21 You have successfully completed the BSG Quick Start Wizard.
22 Verify all of the information that you have entered is correct. If the information is correct, click
Continue to save the information. If you want to make changes to the information, click on the
Change button at the bottom of the page and you will run through the Wizard again.