NRS Healthcare N43541 User manual

Intended Use
The Easylift Over Bed Table Range provide users with a firm, flat surface that is suitable for
eating, writing, reading, etc. The single column construction and adjustable height makes
them suitable for use with most types of beds and chairs. N43565, N43577 & N43589 are also
suitable for use with wheelchairs.
N43541 Easylift Over Bed Table-Beech Top - Standard Base
N43553 Easylift Over Bed Table-Beech Top - Standard Base - Low
N43565 Easylift Over Bed/ChairTable-Beech Top - Curved Base
N43577 Easylift Over Bed/Chair Table-Standard Top - Curved Base
N43589 Easylift Over Bed/Chair Table-Tilt Top - Curved Base
User Instructions
General Safety Warning
Please ensure these instructions are fully read, understood and followed - failure
to do so may result in injury to the user or damage to the product.
Please keep this instruction leaflet for future reference.
N43589
N43577
N43553
N43541
N43565
-

Unpacking - Before assembly:
Read instructions carefully
Take particular care when handling the
Spring Loaded Column (see below).
Check all parts against the contents list below,
if there are any parts missing, damaged or you
suspect a fault do not assemble the product,
contact your supplier immediately.
Note: All tools required to assemble this
product are supplied
List of Components:-
Base Assembly (Castors fitted)
Lift Column Assembly
Top Assembly (Either Fixed or Split Top)
M8 x 50mm Bolts x 3
M8 x 15mm Cap Screws x 4
M8 Washers x 7
Split Washer x 3
Spanner
Allen Key
2 –Assembling Spring Loaded Column to the base
You may require assistance to perform this task
This operation is best done with the base assembly on
its side as shown in Diagram: 2. Secure the column to
the base assembly using the (3) M8 x 50 Bolts and (3)
M8 ID Washers & (3) Split Washers.
3 –Assembling Spring Loaded Column to the table
top. You may require assistance to perform this
task
Place the table top on to a carpeted (non abrasive)
surface. WARNING (N43589 Easylift Over Bed/Chair
Table-Tilt Top version only) When turning the table
top over take care to not allow the hinged angular
section to swing away from the frame. This could
cause damage to the tilt mechanism and could
cause injury.
Assembly Instructions
Diagram:1
Diagram:2
Diagram:3
3 –Continued: Secure the lift column to the top section
using the (4) M8 x 15 Cap Screws and (4) M8
Washers. As shown in Diagram: 3
Before returning the table to its castors it is
recommended that the table be extended to the top of
its height range.
Spring Loaded Column
The column contains a compression spring that
will open rapidly, in the direction shown, if
compressed during assembly. Handle with care.
Once assembled the weight of the table top
ensures that the ‘rapid expansion’does not occur
during use

Tilt Section Adjustment (Diagram:5)
The tilt angle section of the table may be adjusted
to one of five positions
To Increase The Angle:
Hold the edge of the table as shown (B). Lift
the table until the ratchet (C) engages at the
required position.
To Reduce The Angle:
Hold the edge of the table as shown (B). Lift
the table as far as it will go, then lower back
to the flat position.
SAFETY PRECAUTIONS
Always ensure that the table is correctly
positioned and adjusted to allow it to be
used safely and comfortably.
Do not lean or sit on the table.
Do not exceed the Safe Working Load of
25Kg evenly distributed.
Do not place hot utensils, dishes, bowls,
cups, etc. directly on to the table surface.
Maximum heat resistance 65° C or 149° F.
Take care when moving the table over rough
or uneven surfaces. Lift the table over large
ridges and wide gaps.
User Instructions
Height Adjustment - All tables (Diagram: 4)
To lower the table height:
Lift the height adjustment lever (A) and push
the table top downward.
To raise the table height:
Simply pull up the table top to raise.
The ‘height adjustment lever’ is not used.
As well as this being simple to use it also acts
a safety mechanism against accidental
adjustment of electrically operated beds.
User Instructions
WARNING
Take care not to trap fingers between the fixed
and movable parts of the table.
Diagram:4
The table tilting function is only available with:
N43589 ONLY
Diagram:5
B
C

Product Care: Cleaning
Wearing suitable protective clothing, clean all
surfaces with a disposable cloth soaked in
neutral detergent and hot water.
Start by cleaning the upper sections of the
table and work along all horizontal surfaces.
Work methodically towards the lower
sections of the table and clean the castors
last. Take extra care to clean areas that may
trap dust or dirt.
Rinse with clean water and dry with
disposable paper towels.
After cleaning the table as described above,
wipe all surfaces with sodium
dichloroisocyanurate (NaDCC) at a
concentration of 1,000 parts per million
(0.1%)
In the case of pooling body fluids, e.g. blood,
the concentration of NaDCC should be
increased to 10,000 parts per million (1%)
WARNINGS
Avoid excessive wetting of the product,
particularly the table top.
Do not use abrasive compounds or pads.
Do not use phenol-based disinfectants.
Do not use excessively hot water. The table
top has a maximum heat resistance
temperature of 65°C or 149°F.
Product Care: Maintenance
The Easylift Over Bed Table Range are designed
to provide years of trouble free service, however
after prolonged or improper use, the castors,
mechanical lift mechanism, rollers or tilt mechanism
may become worn or damaged.
The following preventive maintenance procedures
should be carried out regularly. In the event that
there is an issue with the product, all service or
repair activities must be carried out by properly
qualified and trained persons.
Height Adjustment: Check that the height
adjustment mechanism functions smoothly and that
the table locks securely in position over the full range
of table height.
Castors: Make sure all four castors are securely
fixed to the base and that they swivel and rotate
freely. Remove any debris that may have been
picked up by the wheels.
UI/ N43577/N43589/0316/Iss3
Product Care: Maintenance - Continued
Tilt Top Table: Check that the table locks securely
in each position.
Service & Warranty
For service, maintenance and any question
regarding this, or any other NRS product, please
contact: [e-mail] or
telephone: [phone]
All Products in the Easylift Over Bed Table
Range are warranted to be free of defects in
materials and workmanship for one year from the
date of purchase. If there is a defect covered by
this warranty, we will, at our option supply parts or
replace the product.
This warranty does not cover product failure due to
owner misuse, negligence or normal wear and tear.
If you have any queries or require full warranty
conditions, please contact NRS Healthcare
Customer Service; details below.
The Easylift Over Bed Table Range is part of a
range of over 3,000 daily living aids available from
NRS Healthcare.
To view the full range please visit our website:
www.nrshealthcare.co.uk
Or request a catalogue from the number below.
IMPORTANT
Additional copies of this user instruction are
available on our website:
www.nrshealthcare.co.uk
NRS Healthcare
Sherwood House,
Cartwright Way,
Forest Business Park,
Bardon Hill,
Coalville,
Leicestershire,
LE67 1UB,
United Kingdom.
Tel. Customer Services: 0345 121 8111
Email: [e-mail]
www.nrshealthcare.co.uk