Oki MPS3537mc Series User manual

1 / 9
GN-1060 with GN-3010
GN-1060 with GN-3010
for MC760/MC770/MC780/ES7460/ES7470/ES7480/MPS3537/MPS4242
SET-UP GUIDE
Warnings Points
• Theunpackingandsetupprocedureshallbedonebyaqualiedservicetechnician.
• Besuretounplugthepowercableoftheequipmentbeforeinstallingandsettinguptheproduct.
• Disconnectthegroundwireafterunpluggingthepowercable.Inaddition,besuretoconnectthegroundwire
beforepluggingthepowercable.
Cautionary Points
• Installtheequipmentnearanoutlet.Besuretowirethepowercablesecurelysoastounplugiteasilyandnot
totripoverit.
• Accordingtotheequipmentmodel,theseillustrationsmaydiffer.
• Thecoversofthisequipmenthavebeendesignedsoasnottobeeasilyremoved.Therefore,whenusing
tools,besurenottoputyourfaceandhandsinthedirectioninwhichforcewillbeapplied;otherwisethiscould
resultininjury.Inaddition,payattentionnottodeformpartsbyusingtoomuchforce.
• Whenunpackingandsettinguptheproduct,besuretowearglovestoavoidinjury.
 Accessories
GN-1060
GN-3010
AB
D
E
f
J H

2 / 9
GN-1060 with GN-3010
 Setup
1. Take out the accessories.
2. Take off the cover.
*Youmustwearglovesforthisprocedure.
1) Remove[b]and[e].
 •b:1
 •e:1
2) Open[F].
3) Pushthelockingbuttontoopen[G].
4) Remove[b].
5) Remove[e].
F
G
b
e
b
e

3 / 9
GN-1060 with GN-3010
6) Openthecoversintheorderof(A)and(B).
7) Close[G].
8) Releasethelatches(A)ofthecover.
 •A:2
* Asshowninthegure,insertaathead
screwdriverintothegrooveandpushitin
thedirectionofthearrowtoreleasethe
latches.
When using tools, be sure not to put your
face and hands in the direction in which
force will be applied; otherwise this could
result in injury.
9) Releasethelatches(B)ofthecover.
 •B:2
* Asshowninthegure,insertaathead
screwdriverintothegrooveandpushitin
thedirectionofthearrowtoreleasethe
latches.
When using tools, be sure not to put your
face and hands in the direction in which
force will be applied; otherwise this could
result in injury.
G
B
A
A
A
B
B

4 / 9
GN-1060 with GN-3010
10)Releasethelatch(D)ofthecover.
 •D:1
* Asshowninthegure,insertaathead
screwdriverintothegrooveandpushitin
thedirectionofthearrowtoreleasethe
latches.
When using tools, be sure not to put your
face and hands in the direction in which
force will be applied; otherwise this could
result in injury.
11)Closer[F].
12)Takeofftheuppersideofthecover,release
thelatch(E)andthentakeoffthecover.
 •E:1place
3. Cut out the gray portion shown in the figure
and dispose of it.
D
E
F

5 / 9
GN-1060 with GN-3010
4. Loosen the screws and take off the cover.
•Screws:15places
5. Set [A] as shown in the figure.
* Makingsurethatitsterminalcontactsthatof
[A],fullyinserttheconnectorandpushitto
theboardsidetosetit.
6. Wire the cable of [D] as shown in the figure,
and then hook [D].
7. Secure [D] with [f].
•f:1
A
f
D
D
D
A

6 / 9
GN-1060 with GN-3010
8. Wire the cable of [D] inside the product as
shown in the figure.
9. Attach [E] and [H].
•E:1
•H:2
10. Set [J] to the position of the cable indicated
in the figure, and fix it with [H].
•H:2
11. Loop the cable twice as shown in the figure,
and fix it with [E].
•E:1
H
H
E
H
J
H
AB
E
D
J

7 / 9
GN-1060 with GN-3010
12. Pass the cable through the hole as shown
in the figure, and connect it with [A].
13. Attach the cover and tighten the screws.
•Screws:15places
14. Insert its latch (E) and then the parts
indicated by the arrows as shown in the
figure.
Perform this operation with care to avoid
injury. In addition, be sure not to damage
the cover.
15. Insert the latches (A) and (B) of the cover.
•A:2places
•B:2places
E
A
B
A
B
A

8 / 9
GN-1060 with GN-3010
16. Open [F].
17. Insert the latch (D) of the cover.
18. Close the covers in the order of (A) and (B).
19. Push the locking button to open [G].
20. Attach [b].
•b:1
G
b
BA
F
D

9 / 9
GN-1060 with GN-3010
21. Attach [b] and [e].
•b:1
•e:1
22. Attach [e].
•e:1
23. Close in the order of [G] and [F].
24. Affix the label [B].
•B:1
25. The operation is now completed.
G
F
b
e
e
45564403EERev.1
OR
1mm
1mm
B
B