olympia electronics KLD-30 User manual

KLD-30, KLD-22, & KLR-20
922502050_09_008
12
922502050_09_008
45
MAINS VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-Cd)
BATTERY PROTECTION
INDICATIONS
RECHARGING TIME
VIEWING DISTANCE
MINIMUM EMERGENCY DURATION
LIGHT SOURCE INTENSITY (230V / EMERG.)
DEGREES OF COVER PROTECTION
OPERATION TEMPERATURE RANGE
PRODUCED IN ACCORDANCE WITH
RELATIVE HUMIDITY
CONSTRUCTION MATERIALS
EXTERNAL DIMENSIONS (LXWXH)
GUARANTEE
KLD-30
KLD-30
KLD-22
KLD-22
KLR-20
KLR-20
LED Characteristics
Charge LED/ Test button
220-240V AC / 50-60Hz
3 hours
24 hours
22m 20m30m
Overcharging and deep discharging protection
3.6V/1 Ah
3.2W / 3.4VA
EN 60598-1, EN 60598-2-22, EN 55015,
EN 61547, EN 61000-3-2, EN 61000-3-3
75lm/75lm
IP54
o
5 to 40 C
up to 95%
PC, Acrylic plate PC
3 years (1 year for the battery)
Olympia Electronics S.A.
45 °C max. across the board
11.2-13.2V DC
0.72W
0405183
Built-in main board
Warranty
IP54
Maintained
M
75lm
Light output
3h
Duration
30m22m20m
KLD-22 & KLD-30
KLR-20
12
The light source of this luminary is not replaceable when the light source
reaches its end of life the whole luminary shall be replaced.
ATTENTION!!!
KLD-30
KLD-22
KLR-20
MAINTAINED EMERGENCY ILLUMINATION SIGNS
Thank you for your trust in our products
Olympia Electronics - European manufacturer
European
manufacturers
Technical Characteristics
MANUFACTURER
MODEL NUMBER
VOLTAGE RANGE
CONNECTIONS
NOMINAL POWER
TEMPERATURE (tc)
Olympia Electronics guarantees the quality, condition and operation of the goods. The
period of warranty is specified in the official catalogue of Olympia Electronics and also in
the technical leaflet, which accompanies each product. This warranty ceases to exist if
the buyer does not follow the technical instructions included in official documents given
by Olympia Electronics or if the buyer modifies the goods provided or has any repairs or
re-setting done by a third party, unless Olympia Electronics has fully agreed to them in
writing. Products that have been damaged can be returned to the premises of our
company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to
or not charge the buyer depending on the reason of defection. Olympia Electronics
reserves the right to charge or not the buyer the transportation cost.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
E: With non-replacable lamp(s) and/or battery
G: Internally illuminated safety sign
180: 3 hours duration
(*) Maintained operation: The luminary lights its illumination source, when it is
powered by the mains power supply or not.
Non Maintained operation: The luminary lights its illumination source, only in
power supply’s failure.
Legend installation-replacement
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[e-mail]
TYPICAL WEIGHT 520gr.920gr. 700gr.
254x35x170mm254x35x180mm310x35x216mm

922502050_09_008
These luminaries are used indoors
o
(ta 40 C) on th e wa ll, where
emergency light is needed. Each
luminary must be permanently
connected to mains power supply.
In normal operation the battery is
charging. In case of a mains power
supply failure the luminary will
light the led strip automatically in
emergency mode. When the mains
power supply is restored the device
turns to normal operation.
Non Maintained / maintained
operation there is an option to
select the non maintained or
maintained operation by placing
the jumper to the appropriate
position according to figure 4 (see
page 3).
Installation
T yo install the luminar follow the
installation instructions on pages 2
and 3.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation,
maintainance or testing must be
done by authorized personnel only.
2. The device must be connected
to the mains power supply through
a fuse dependent by the total
amount of the line’s power load.
3. It is suggested to check every
month the indication LED for
battery charging, and by pushing
the TEST button to check the
emergency circuit. The led strip
should light as long as the TEST
b u t t o n i s p r e s s e d a n d t h e
indication LED for battery charging
should be off. If the luminary
doesn’t work as described above
contact the installer.
4. It is suggested to check every 6
months the minimum autononous
duration by disconnecting the
mains power supply. Count the
time that the led strip lights and in
case of less time than the nominal
autonomy, the battery must be
replaced. If the measured time is
considerably less than the nominal
autonomy In contact the installer.
case of battery replacement, this
must be replaced by part of the
same type, by the manufacturer or
by a competent person.
5. In case of inactive use for a
period greater than 2 months,
disconnect the battery by pulling
out the battery’s connector.
6. I s not allowed to discard t i
batteries in to common
trash bins, they must be
discarded only in battery
recycling points. Do not
incinerate.
Test Button- Manual Test for
emergency operation
The manual test can be conducted
only if the mains power supply and
the battery is connected:
After 3 seconds, the luminary
returns to normal operation.
Indication LED status
Charge
On: Fully charged.
Off: No battery (No charging
current or disconnected battery).
Blink: Charging.
1
1
1
1
Luminaire
Wall mounting accessorie
Ceiling mounting accessorie
Manual
Package contents
Γενικά
1922502050_09_008 2922502050_09_008
Installation methods
Wall mounting
Luminary disassembly
Luminary assembly
3
Battery replacement
4
3
5
2
1
Ενδεικτικά
12
N
L
Insert the
power cable
Insert the
power cable
Insert the
power cable
Insert the
power cable
1. Disassemble the luminary.
2. Remove the battery connector and carefully remove the battery from its base.
3. Install a new battery of the same type and rating.
4. Assemble the luminary and power the device.
Α-2130: Accessorie for ceiling (1m)
Α-2131: Accessorie for ceiling (0,5m)
Α-2132: Accessorie for ceiling (0,25m)
Α-2133: Accessorie for wall mounting
Α-2136: Accessorie for hanging installation (2,5m)
A-2520/PL: Suspended ceiling base
>5mm
General
Insert the
cable grommet
Hanging installation
After the desired installation follow the steps below
Ceiling mounting
Maintained
(default)
Non
maintained
Battery
connection
Accessories for installation
(After request)
Insert the
cable grommet
Insert the
cable grommet
Insert the
power cable