olympia electronics GR-938/30L User manual

Page 1 from 4 923939100_09_013
GENERAL
These luminaires are used in places where
emergency luminaires are needed. Each
luminaire must be permanently connected to
mains power supply. In normal operation (L1
connected to L) the led strip lights and the
battery is charging. In case of a mains
power supply failure the luminaire will light
the led strip automatically in emergency mode
(powered by its battery). When the mains
power supply is restored the device turns to
normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 3.
OPERATION
Battery Charging
The battery charging is completely controlled.
Thereby, the best possible battery
maintenance is achieved, as well as the
elongation of its duration. When the battery
has completely charged, it charges with a
maintenance current.
Battery Cut-off
The luminaire enters in this operation when
the mains power supply fails and battery has
lost its energy. During this operation the
luminaire enters the idle state and battery
consumption is negligible, in order to be
protected from deep discharge.
Manual Test
The manual test can be conducted only if the
mains power supply and the battery is
connected. By pressing the TEST/RESET
button briefly (page 3) an operation test is
initiated. During this test period all indication
LEDs are OFF.
Tests
Normally the illumination source and the
autonomy tests are programmed by the
control panel and the test results are sent to
the control panel.
Automatic Operational Test
This test includes all the operations that
provide the manual test and is conducted
automatically every 15 days. In order to be
performed, the mains power supply and the
battery should be connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the device’s back up operation
220-240V AC/50-60Hz
4.5W / 4.9VA
ABS/PC, PC
TECHNICAL CHARACTERISTICS (for LED MODULE Specs. see page 4)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION (MAINS / EMERGENCY)
ILLUMINATION SOURCE
90min
24h
Charge, Lamp Fault, Battery Fault indication LED
From overcharge and deep discharge
IP 65
3.6V/3Ah
210lm / 210lm
30 white LEDs
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
5 to 40 C
o
Up to 95%
3 years (1 year for the battery)
930gr.
363 x 145 x 73 mm
3.4W / 3.8VA
GR-938/15L GR-938/30L GR-939/15L GR-939/30L
3.6V/0.6Ah
105lm / 105lm
15 white LEDs
180min
5.3W /5.6VA3.3W / 3.7VA
3.6V/1.5Ah
210lm / 210lm 105lm / 105lm
30 white LEDs 15 white LEDs
790gr. 860gr.
Thank you for your trust in our products.
Olympia Electronics - European manufacturer.
WATERPROOF SELF TESTING MAINTAINED EMERGENCY LUMINAIRES

and emergency duration. This test is
conducted automatically every 6 months. In
order to be performed, the mains power
supply and the battery should be connected
and fully charged. If the battery is not fully
charged, the test is postponed until the battery
is completely charged. If during this test, the
autonomy is less than nominal then the battery
fault led turned on continuously and the
battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the list of the technical
characteristics. During emergency mode, a
light source test is also performed.
Resetting Errors
Push the TEST/RESET button for 5 seconds,
to delete all the indicated LED errors (page 3).
Then the luminaire enters regular operation
mode.
Indication LED status (with connected
mains power supply).
Charge
On: Good charge condition.
Οff: No battery (No charging current
or disconnected battery).
Lamp Fault with L1 connected to L
Οn (with LED strip off): Faulty LED strip
(must be replaced).
Οn (with LED strip on): Problem in the back
up circuit of the LED strip (must be checked by
an authorized personnel).
Off: Good LED strip.
Battery Fault
Οff: Battery OK.
Blink (With Charge LED ON): Autonomy or
low battery problem (the battery must be
replaced).
Blink (With Charge LED Off): No charging
current or disconnected battery.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or
testing must be done by authorized personel
only, after a mains interruption.
2. The device must be connected to the mains
power supply through a fuse dependent on the
total amount of the line’s power load.
In case of battery or lamp replacement,
these must be replaced by parts of the same
type, by the manufacturer or by a competent
person.
3.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
5. I s not allowed to discard batteries in to
common trash bins, they must be
discarded only
t i
in battery recycling
points. Do not incinerate.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
G: Internally illuminated
90: 1.5 hour duration
180: 3 hours duration
(*) Maintained operation: The luminaire lights
its illumination source, when it is powered by
the mains power supply or not.
Non Maintained operation: The luminaire lights
its illumination source, only in power supply’s
failure.
Note!! The installer should fill in, on the
specification label, the letter G if the luminaire
is used as a safety sign.
NOTE!! After finishing the installation you
must power the luminaire at least for 24
hours for battery charging to perform the
nominal autonomy.
Battery replacement
It can be done only by a competent person
and after the mains interruption.
1. Unfasten the 4 retaining screws (not all the
way) (step 10 of the installation instructions)
and remove the diffusor.
2. Unfasten the 2 retaining screws (step 9 of
the installation instructions) and remove the
reflector.
3. Remove the old battery and place a new
one of the same type and characteristics.
4. Replace the removed parts (previous steps
1,2).
The light source contained in this
luminaire shall only be replaced by the
manufacturer, or his agent, or a similar
qualified person.
NOTE! The light source is non-user
replaceable.
923939100_09_013
Page 2 from 4
X19 0A G

INSTALLATION INSTRUCTIONS FOR WALL OR CEILING MOUNTING
1
8
910
67
N
L
N
L
L1 L N L1 L N
External
switch
Controlled operation of the lamp
Link
Permanent maintained operation
1 Remove the diffusor. Place a flat blade screwdrivers and pull up gently the reflector.
2 Install the included plastic cover in to the unused hole and install the base plastic (with the
included mounting screws and plugs).
3 Always use in any case round mains cable, with external diameter of 6-9mm (H05RN-F
type 2x1mm² or any other type, at least equal to it’s mechanical and electrical properties).
ATTENTION!! The cable must not be deformed in any way (This requirement is important
to ensure the IP65 rating). Install the cable gland, pass the round cable through and tighten it all
the way.
4 Place the battery’s connector to the corresponding connector on the P.C.B.
5 Connect the mains cables to the respective terminal block (connect the ground wire if required).
6 Ν for neutral, L for live wire and L1 for the maintained operation. The L1 wire can be connected
to an external switch to control the maintained or non maintained operation of the luminaire.
7 For permanent maintained operation use two wires to power the luminaire, Ν for neutral and L for
live wire, and link the L and L1.
8 Install the included tie (if needed) to fasten securely the power cables.
9 Refit the reflector and fasten the two small screws (included).
10 Finally place the diffusor by using the 4 included screws (tightening torque 1.2 Nm).
23
L1 L N
45
Page 3 from 4 923939100_09_013
Manual TEST or Resetting Errors
In order to test or reset the device
you must carefully remove the
diffusor by unfastening the 4
mounting screws. Then push the
button as described in the according
paragraphs on page 1 and 2.

923939100_09_013
Page 4 from 4
LED MODULE CHARACTERISTICS
Olympia Electronics S.A
45 °C max. across the board
Cable connection with non reversible connectors
8.5-10.5 V DC
1W 2W
1605163/15L 1605163/30L
GR-938/15L GR-939/15L GR-938/30L GR-939/30L
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]