Olympus HysteroFlow User manual

HysteroFlow / HysteroBalance II
Hysteroscopic Fluid Management System
Quick Reference Guide

2Hysteroflow Quick Reference Guide
This quick reference guide is only a summary
of the HysteroFlow/HysteroBalance II
Instructions for Use. For detailed operating
instructions, be sure to follow the Instruction
Manual that was included with your
device when purchased.
Warning

3Hysteroflow Quick Reference Guide
1. Turn the unit on.
2. After self test, press Menu to check or
change system settings. (Refer to page
4 for menu settings)
3. Hang fluid irrigation bags on the upper
scale hooks.
4. Close inflow and outflow stopcocks on
the instrument.
5. Connect blue Leur Lok on the inflow
tubing to the inflow port on the
instrument.
6. Press OK next to Operative Mode and
press Start.
7. Carefully insert the pressure chamber
on the inflow tubing into the lower
retainer on the pump, and wrap the
tubing up and around the roller wheel,
locking it into place.
8. Clamp tubing and spike fluid irrigation
bag(s). Open one clamp.
Connect Inflow Tubing

4Hysteroflow Quick Reference Guide
Menu Settings
After each menu selection,
press OK.
Nominal Flow Menu
Select a nominal flow value between
30 and 500 ml/min.
Maximum Deficit Menu
Select a deficit threshold value
between 200 and 2500 ml.
Alarm Volume Menu
Select a volume between 1 and 5.
Bag Size
Select a bag size between 0 and
5 liters.
General Settings Menu
To view and change Language,
Sensor Test, Factory Defaults,
Demo Mode, Brightness.

5Hysteroflow Quick Reference Guide
Connect Outflow Tubing
Instrument Recognition (IR)
1. Open the inflow stopcock on the
instrument.
2. Close the outflow stopcock on the
instrument.
3. Hold the instrument at operative
height.
4. When prompted, press Yes to begin
IR activation.
5. Turn the inflow stopcock off when
IR is complete. Screen prompt and
single beep indicate IR completion.
Do Not Press Stop!
1. Place containers on the bottom scale
and toggle them with the connection
tubes.
2. Connect the yellow Leur Lok on the
outflow tubing to the outflow port
of the instrument.
3. Connect the short end of the Y tube
to the patient drape.
4. Connect the long end of the Y tube
to the “Patient” port of the first
container.
5. Connect the last container tubing
to suction.
To Suction
Outflow

6Hysteroflow Quick Reference Guide
Warnings
Begin the procedure
Begin the Procedure
1. Press Details to display inflow
and outflow volumes.
2. Press (–) or (+) to set Nominal Pressure.
3. Press Reset Actual Deficit, then
press Yes.
4. Open inflow then open outflow
stopcocks on the instrument to
begin the procedure.
Warning Message Alert Cause
Change Fluid Bag 3 Beeps > 500 ml remaining
Deficit Reached 3 Beeps Deficit exceeds the preset value
Overpressure 3 Beeps Actual pressure 10 mmHg above nominal pressure
Deficit Exceeded 10 Beeps In increments of 100 ml above the preset value
Critical Overpressure 10 Beeps Actual pressure > 200 mmHg above nominal
pressure
Rapid Deficit 10 Beeps Deficit change > 300 ml in 1 minute

7Hysteroflow Quick Reference Guide
System Accessories
WA40634A
Inflow and Outflow Tubing Set, Sterile, 5/pkg
WA40635A
Inflow Tubing Set, Sterile, 10/pkg
006772-901
3L Canisters 36/pkg
Part # Description
WA40634A Inflow and Outflow Tubing Set, Sterile, 5/pkg
WA40635A Inflow Tubing Set, Sterile, 10/pkg
006775-901 Under Buttocks Drape/Fluid Collection Set, 5/pkg
006772-901 3L Canisters 36/pkg

This is designed as a quick reference guide only.
This guide is not a substitute for reading and learning the
entire Operator’s Manual and/or Instructions For Use (IFU)
provided with the HysteroFlow/HysteroBalance II System.
Olympus cannot encourage or recommend any actions that
deviate from or are not covered by the IFU.
Olympus is a registered trademark of Olympus Corporation, Olympus America Inc., and/or their affiliates.
Medical devices listed may not be available for sale in all countries.
For more information, contact your Olympus
sales representative, or call 800-848-9024.
www.medical.olympusamerica.com
©2019 Olympus America Inc. All rights reserved.
Printed in USA OAIGYN0319QRG29604
136 Turnpike Road, Southborough, MA 01772
For Assistance: 800-848-9024
Option 1: Technical Assistance
Option 2: Orders/Order Status
Option 3: Service & Repair