Optex SL-100 TNR User manual

EN-1
BATTERY OPERATED
PHOTOELECTRIC DETECTOR
BATTERY OPERATED
PHOTOELECTRIC DETECTOR
CONTENTS
1 INTRODUCTION
1-1 BEFORE YOUR OPERATION ............................... 2
1-2 PRECAUTIONS...................................................... 3
1-3 PARTS IDENTIFICATION...................................... 3
2 PREPARATIONS......................................................... 4
3 INSTALLATION
3-1 SEPARATING ........................................................ 5
3-2 WALL MOUNTING ................................................ 5
3-3 POLE MOUNTING ................................................. 8
3-4 MOUNTING EXAMPLE AT PARTICULAR CASE.. 9
3-5 WIRING .................................................................. 9
4 SETTINGS
4-1 FUNCTIONS......................................................... 11
4-2 OPTICAL ALIGNMENT ........................................ 12
5 OPERATION CHECK
5-1 LED INDICATION................................................. 13
5-2 OPERATION CHECK........................................... 13
6 TROUBLESHOOTING............................................... 14
7 DIMENSIONS............................................................. 14
8 SPECIFICATIONS ..................................................... 15
9 OPTIONS ................................................................... 16
INSTALLATION INSTRUCTIONS
FEATURES
No.59-2606-0 1612-16
Smart Line series
Smart Line series
MODEL DETECTION RANGE
30 m / 100 ft.
60 m / 200 ft.
SL-100 TNR
SL-200 TNR
™
™
•Battery operated detector
- D size lithium battery or CR123A lithium battery
(OPTION CRH-5)
•Simplified optical adjustment
- Sniper View Finder with ×2 magnification
•Avoids having to install a wireless transmitter in the
photoelectric transmitter.
- IR signal transmission technology transfers the low
battery signal to the receiver
•Possible to connect the power and alarm cables to both
the receiver and the transmitter or either of them
- OPTION PCU-5
•Long battery life
•Battery saving function
•Intermittent output function
•Slim body design
•Easy to see vivid interior color for optical alignment
•IP65 waterproof structure
•Tamper function
•Indicator LED for an easy alignment
•Various options (Refer to "2 PREPARATIONS" and
"9 OPTIONS").)
(CRH-5, BCU-5, PCU-5)

EN-2
Warning
Caution
This symbol indicates prohibition. The specific prohibited action is provided in and/or around the figure.
This symbol requires an action or gives an instruction.
Do not use the product for purposes other than the detection of moving objects such as people and vehicles.
Do not use the product to activate a shutter, etc., which may cause an accident.
Never attempt to disassemble or repair the product. It may cause fire or damage to the devices.
Do not use batteries that have different levels of power remaining (i.e., new and used batteries). Not
observing the above may result in an explosion, leakage of electrolyte, emission of toxic gases or other
outcomes that may be harmful to people and property.
[Handling of Batteries] Do not recharge, short circuit, crush, disassemble, exceed heat above 100°C (212°F),
incinerate, or expose contents to water. Do not solder directly to the cell.
Do not pour water over the product with a bucket, hose, etc. The water may enter, which may cause damage
to the devices.
Clean and check the product periodically for safe use. If any problem is found, do not attempt to use the
product as it is and have the product repaired by a professional engineer or electrician.
Do not touch the unit base or power terminals of the product with a wet hand (do not touch when the
product is wet with rain, etc.). It may cause electric shock.
Warning
Caution
1INTRODUCTION
1-1 BEFORE YOUR OPERATION
•Read this instruction manual carefully prior to installation.
•After reading, store this manual carefully in an easily accessible place for reference.
•This manual uses the following warning indications for correct use of the product, harm to you or other people and
damage to your assets, which are described below. Be sure to understand the description before reading the rest
of this manual.
Failure to follow the instructions provided with this indication and improper handling may cause
death or serious injury.
Failure to follow the instructions provided with this indication and improper handling may cause
injury and/or property damage.

EN-3
1-3 PARTS IDENTIFICATION
1-2 PRECAUTIONS
Do not install the unit on
an unstable surface.
Do not install the pole in a
location where sufficient
stability can not be
ensured.
Do not install the unit in
trees, leaves, or other
objects that may swing in
the wind and block the
beam.
Do not install the receiver
in a location where it is
exposed to direct sunlight.
Do not allow the infrared
beam from an other pair of
the detector to reach the
receiver.
Install the unit at least 1 m
(3.3 ft.) away from the wall
or fence that may be running
parallel to the beam.
This symbol indicates prohibition. This symbol indicates recommendation.
Install the unit at a height
where an object can be
detected without fail.
The pole size should be
43 to 48 mm dia.
(1.69 to 1.89 inch dia.).
Main unit cover
Battery cover
Main unit Back box
Viewfinder
Optical
alignment dial
Optical lens
Battery cover
lock screw
Battery
Plate
Main unit cover
lock screw
Main unit mounting
bracket
Dip SW
(Receiver only)
Unit: mm (inch)
141 (5.6)
35 (1.4)
47 (1.9)
Wireless transmitter size
Receiver
Transmitter
(another
detector)
Receiver
(another
detector)
Transmitter
1 m (3.3 ft.)

EN-4
2PREPARATIONS
Velcro tape: 1 set
4×20 self tapping for wall mounting
(with rubber washer): 4 Cables: 3
U-brackets: 2Pole brackets: 2
M4×16 screws for pole mounting
(with rubber washer): 4
Accessories
1. Both transmitter and receiver use batteries *= depends on each type of the wireless transmitter
** = Refer to "9 OPTIONS"
2. Eithertransmitter or receiver powered by wired source
3. Both transmitter and receiver are powered by wired source
Detector Wireless transmitter
Shared
Independent
Shared
Independent
Power source selection
D size
CR-123A
Detector Wireless transmitter
Shared
Independent
Shared
Independent
D size +
wired
CR-123A
+ wired
Detector Wireless transmitter
Shared
Independent
Wired
D size CR-123A Other *CRH-5 BCU-5 PCU-5
4 - - - 1 -
4 - *- - -
- 16 - 2 1 -
- 16 *2 - -
**stesnoitpOseirettaB
Numberof required sets
D size CR-123A Other *
2 - -
2 - *
- 8 -
- 8 *
CRH-5 BCU-5 PCU-5
- 1 1
- - 1
1 1 1
1 - 1
D size CR-123A Other *
- - -
- - *
CRH-5 BCU-5 PCU-5
- 1 2
- - 2

EN-5
4Remove the main unit from the back box.
5Remove the main unit mounting bracket.
3
1
2
Take the main unit out of the back box.
2
Turn the optical unit
90 degrees and
loosen the screw.
1
Caution
Do not place the main unit where it is exposed to
direct sunlight. Doing so may cause damage to the
product.
1Using a screwdriver or similar tool, break the knockout position (×2) in the back box as shown.
3-2 WALL MOUNTING
Break the knockout
from inside of the
back box as shown
direction, to avoid
the making burrs.
Knockout position
WALL
POLE (1)
POLE (2)
1Remove the battery cover. 2Remove the main unit cover. 3Remove the connectors.
3INSTALLATION
3-1 SEPARATING
Pull
2
Loosen the
battery cover
lock screw.
1Pull
2
Loosen the
main unit cover
lock screw.
1

EN-6
3Using Velcro tape, fix the wireless transmitters in the back box.
For more information on wiring, see “3-5 WIRING”.
4Mount the main unit.
Note>>
• When using BCU-5 (option), refer to
BCU-5 manual.
Velcro tape
Cut the supplied Velcro
tape to an appropriate
length and apply.
Tighten the main unit
fixing screw and turn the
optical unit 90 degrees.
3
1Attach the main unit
mounting bracket to the
back box.
2Route the three connectors
of the back box through the
slits on the upper part of the
main unit.
1
3
4
2
2Mount the back box to the wall.
4×20 self tapping
(with rubber washer)
Side wall
Distance from
the side wall:
at least 1m
Pitch: 83.5 mm
For connection
to gang electric
box

EN-7
Attach the connectors.
5
Insert batteries.
• Apply the same procedure for the battery replacement.
6
Note>>
•Avoid placing the cables in a
position where they can be
caught between the main unit
and cover.
Disposal method for batteries
Insert the two batteries into their compartment.
Ensure the positive terminals are facing toward
the front.
2
Close the battery plate.
3
Connect the CRH-5 male connectors to the
female connectors of the battery plate.
4
1Open the battery plate in the direction of the
arrow.
Set CR123A in the CRH-5 and insert two CRH-5
into their compartment. Ensure the positive
terminals are facing toward the front.
2
Close the battery plate.
3
1Open the battery plate in the direction of the
arrow.
< When using D size battery >
< When using CR123A battery >
Dispose of used batteries in accordance with local government regulations/laws and EU Battery
Directive (2013/56/EU).
1
3
4
2
D size
Lithium batteries
CR123A
put into CRH-5
Warning
•Do not mix D size lithium batteries with CRH-5 batteries.
•Do not mix batteries that have different levels of power remaining (i.e., new and used batteries or batteries of
different manufacturers). Not observing the above may result in an explosion, leakage of electrolyte, emission
of toxic gases or other outcomes that may be harmful to people and property.
Caution
•Remove all batteries prior to replacing with new ones. If this is not followed, the low battery indicator LED will
not reset and will continue to blink.
•When returning this detector to the supplier, remove all batteries from both transmitter and receiver.
Referring to “4 SETTINGS”, perform the necessary settings.
7

EN-8
3-3 POLE MOUNTING
Using a screwdriver or similar tool, break the knockout position (×2) in the back box as shown.
1
Close the main unit cover.
8Close the battery cover. 9
One detector
Two detectors in
opposing directions
Knockout position
Detector No. 1 Detector No. 2
Instruction
condition
POLE (1) -
POLE (1) POLE (2)
Break the knockout from inside of the back box
as shown direction, to avoid the making burrs.
Knockout position
WALL
POLE (1)
POLE (2)
Caution
• Unnecessary knockout broken wrong,
should be closed with a waterproof
material. Otherwise, it may result in
waterproof failure and malfunction of the
product.
Caution
• Do not touch the optical unit when mounting the
cover. Otherwise, the resulting shift of the optical
axis may result in malfunction of the unit and
require readjustment.
Caution
• When closing the cover, be careful that the
cables are not caught by the cover.
Tighten the fixing screw for the battery cover.
2
Close the battery cover.
1
1
2
3
Hook on the upper part
of the back box.
Push the lower part of
the main unit cover.
Fasten the main unit
cover lock screw.
2
1
3
Just fit

EN-9
3-5 WIRING
3-4 MOUNTING EXAMPLE AT PARTICULAR CASE
Receiver
Red
Black
Main unit
Yellow
Orange
Brown
Green
Blue
Purple
Gray
Battery
Plate
Alarm
COM
Low battery
Tamper
NC
NO Wireless
Transmitter
Back box
Transmitter
Red
Black
Main unit
Green
Blue Low battery Wireless
Transmitter
Back box
revieceRrettimsnarT
[ Top view ]
ex) SL-200TNR 60m/200ft. 30m/100ft.
It is not recommended to be installed the
transmitter and the receiver facing each other
through the corner of the cover.
1
Fix the back box on the pole.
2
In doing this installation, the maximum detection
range shall be half of the original detection range.
(This is to compensate the attenuation of beam by
the corner of the cover.)
2
3
Side wall
M4×20 screw
(with rubber washer)
Pole bracket U-bracket
Distance from the side
wall: at least 1m
Pole 43 to 48 mm dia.
(1.69 to 1.89 inch dia.)
Detector
No. 1
Detector
No. 2
Battery
Plate
Note>>
•This section shows for reference as an example of duplicate communication.
•It can usually be omitted because the low battery signal of the transmitter is to be
sent to the receiver through the infrared beam.
Perform the same procedure as 3 to 9 of "3-2 WALL MOUNTING".
•If a wireless transmitter has an N.O. output
output the low battery and tamper output
cannot be used.
Note>>

EN-10
When connecting to
PCU-5 (OPTION)
PCU-5 is used to enable
wired operation. For more
information about this option,
see PCU-5 manual.
BCU-5 allows to share power source and low battery signals between the main unit and the wireless transmitter.
For more information on connecting, see BCU-5 manual.
Note>>
•Route the cables through the center
hole as illustrated.
Note>>
•This section shows for reference as an example of
duplicate communication.
•It can usually be omitted because the low battery signal
of the transmitter is to be sent to the receiver through
the infrared beam.
•When using PCU-5 (option) with either
the transmitter or receiver, ensure that
the low battery signal is monitored at
the other which is battery operated.
Refer to PCU-5 manual.
When connecting to BCU-5 (OPTION)
Receiver
Red
Black
Main unit Back box
Battery
Plate
Battery
Plate
Alarm
COM
N.C.
N.O.
EX EX – +
Low battery
+
–
Tamper
BCU-5
Transmitter
Red
Black
Main unit
Blue
Green
–+
Back box
Yellow
Orange
Brown
Green
Blue
Purple
Gray
Power/
Low battery
indicator LED
Battery Plate
Through the
center hole.
Attach the BCU-5 to the battery plate
using double-sided adhesive tape.
• Be careful not to cover the power/low
battery indicator LED.
• Select a location that does not interfere
with the connector installation.
1Plug the Power line (Red/
Black) into the connector
on the Battery Plate.
2Wire the Red/Black line through
the groove of the Battery Plate,
so that the Battery Cover does
not pinch the line.
3
Warning
Do not insert batteries into the wireless transmitter,
when using BCU-5 option.
Doing so may result in fire or explosion.
Battery Plate Battery Plate
BCU-5
Wireless
Transmitter
EX EX – +
Low battery
+
–
BCU-5
–+
Through the
center hole.
Wireless
Transmitter
BCU-5
•If a wireless transmitter has an N.O. output output
the low battery and tamper output cannot be used.
Note>>