Orbit X304 User manual

Orbit X304
Assembly Instrucons

Spare part list 3
4
5
6-7
8-10
Spare part list
Spare part list
Assembly（1）
Assembly（2）
Assembly（3）
Assembly（4）
Assembly（5）
11-12
13-14
15-16
17-18
19-20
21-22
23-24
25-26
27-28
29-30
Assembly（6）
Assembly（7）
Assembly（8）
Assembly（9）
Assembly（10）
Assembly（11）
Assembly（12）
31-33
Warranty Card
Table of Contents
Owner’s Manual Orbit BK-3059
C
AUTION:
E
xercise of a strenuous nature, as is customarily done on this equipment, should not be undertaken
w
ithout first consulng a physician. Nospecific health claims are made or implied as they relate to
t
he equipment. Measurements made by the equipment are believed tobe accurate, but only the
m
easurements of your physician should be relied upon.
I
MPORTANT:
R
ead all instrucons carefully before using this product. Retain this product owner's manual for
future reference.

Spare parts list
3
No. Descripon Note Qty.
1 connecon tube 1
2 upright frame le1
3 upright frame right 1
4 bending tube le1
5 bending tube right 1
6 upper connecon tube 1
7 upper bending tube right 1
8 upper bending tube le1
9 hexagon bolt M10x75 54
10 lock nut M10 105
11 washer Φ10 217
12 chin up bar 1
13 upper plate 4
14 pulley frame tube right 1
15 pulley frame tube le1
16 upright tube 2
17 tube with hole right 1
18 tube with hole le1
19 lower plate 4
20 sliding tube right 1
21 sliding tube le1
22 foot tube cover 2
23 end tube 2
24 hexagon bolt M10x80 14
25 lower base 2
26 upper base 2
27 guide rodΦ25x1850 2
28 lock sleeve 2
29 sliding sleeve 2
30 rubber pad with groove Φ60xΦ26x45 2
31 safety hook right 1
32 safety hook le1
33 hexagon bolt M10x90 8
34 socket set screw M8x10 4
35 end cap 2

4
Spare parts list
No. Descripon Note Qty.
36 check ring 2
37 pipe
Φ
2
38 buon head socket screw M12x40 2
39 spring washer Φ12 6
40 washer Φ12 6
41 barbell rod 1
42 inner pipe
Φ
2
43 rubber pad Φ60xΦ26x25 2
44 upper connecon tube short 1
45 lower connecon tube 1
46 big sliding sleeve 1
47 guide rod hollow 2
48 rubber pad Φ60xΦ26x45 2
49 hexagon bolt M10x25 11
50 hexagon bolt M10x95 3
51 hexagon bolt M10x55 2
52 hexagon bolt M12x30 4
53 double pulley bracket 1
55 back barbell plate holder 2
56 wire Φ5x2745mm 2
57 pulley Φ95 25
58 pulley plate 6
59 hexagon bolt M10x45 17
60 hexagon bolt M10x50 4
61 weight 2
62 wire L=4740mm 1
63 ”-“ shape pulley frame 3
64 short bar 1
65 footplate 1
66 chain + 2 snap hook 1
67 wire Φ5x4095mm 2
68 pulley spacer sleeve
Φ
16
69 pulley frame 1
70 wire Φ5x1705mm 1

Spare parts list
5
0 1 6 7 8 9 10 11 12 13 14 152 3 4 5
Bolt length measurement ruler
cm
No. Descripon Note Qty.
71 5 secon chain + snap hook 1
72 wire Φ5x9715mm 1
73 pulley Φ50 4
74 shield 1
75 barbell plate holder 6
76 hexagon bolt M8x20 16
77 washer Φ8 20
78 lock nut M8 4
79 core trainer 1
80 powder metallurgy sleeve 2
81 barbell rod cup 1
82 big washer Φ25x10x2.0 1
83 dip bar le1
84 dip bar right 1
85 barbell rod holder right 1
86 barbell rod holder le1
87 barbell rod holder short le1
88 barbell rod holder short right 1
89 barbell clamp collar 2
90 long bar 1
91 ship rod 1
92 hand belt 2
93 pull lidevice 1
94 T shape pin Φ10x100 1
95 leg curl tube 1

Assembly step（1）explosion drawing
6
8
2
6
4
1
5
3
7
9
10
11
9
9
9
10
9
10
9
9
9
22
22
Install ALL bolts/ nuts before ghtening.
Do not over ghten.
No. Descripon Note Qty.
1 connecon tube 1
2 upright frame le1
3 upright frame right 1
4 bending tube le1
5 bending tube right 1
6 upper connecon tube 1
7 upper bending tube 1
8 upper bending tube le1
9 hexagon bolt M10*75 16
10 lock nut M10 16
11 washer Φ10 32
22 foot tube cover 2

Assembly step（1）drawing
7
Assembly step（1）assembly instrucon
1 Fix bending tube le-4 fastening on upright frame le-2 using M10x75 hexagon bolt-9, Φ10
washer-11 and M10 lock nut-10
2 Fix bending tube right-5 fastening on upright frame right-3 using M10x75 hexagon bolt-9, Φ
10 washer-11 and M10 lock nut-10
3 Fix connecon tube-1 fastening with bending tube le-4, bending tube right-5 using M10x75
hexagon bolt-9, Φ10 washer-11 and M10 lock nut-10
4 Fix upper connecon tube-6 fastening on upright frame using M10x75 hexagon bolt-9, Φ10
washer-11 and M10 lock nut-10
5 Fix upper bending tube le-8 fastening on upright frame le-2 using M10x75 hexagon bolt-9,
Φ10 washer-11 and M10 lock nut-10
6 Fix upper bending tube right-7 fastening on upright frame right-3 using M10x75 hexagon bolt-
9, Φ10 washer-11 and M10 lock nut-10
7 Tighten all bolts and nuts before connuing.

Assembly step（2）explosion drawing
8
12
13
15
14
16
18
17
19
21
20
22
9
24
11
10
11
9
9
24 24
24
9
9
24
24
9
23
23
11 10
11
11
No. Descripon Note Qty. No. Descripon Note Qty.
9 hexagon bolt M10x75 38 17 tube with hole right 1
10 lock nut M10 44 18 tube with hole le1
11 washer Φ10 88 19 lower plate 4
12 chin up bar 1 20 sliding tube right 1
13 upper plate 4 21 sliding tube le1
14 pulley frame tube right 1 22 foot tube cover 2
15 pulley frame tube le1 23 end tube 2
16 upright tube 2 24 hexagon bolt M10x80 6
Install nuts and bolts hand ght first before
ghtening.

Assembly step（2）drawing
10
Assembly step（2）assembly instrucon
1
Fix sliding tube le-21 on tube with hole le-18
2
Fix sliding tube right on tube with hole right-17
3Fix upright tube-16 and tube with hole le-18 fastening on assembly step-1 using M10x75
hexagon bolt-9, Φ10 washer-11, M10 lock nut-10, upper plate-13 and lower plate-19
4Fix pulley frame tube right-14 and pulley frame tube le-15 fastening on upper plate-13
using M10x75 hexagon bolt-9, Φ10 washer-11 and M10 lock nut-10
5
Fix end tube-23 fastening on upper plate-13 using M10x75 hexagon bolt-9, Φ10 washer-11
and M10 lock nut-10
6Fix foot tube cover-22 fastening on lower plate-19 using M10x75 hexagon bolt-9, Φ10
washer-11 and M10 lock nut-10
7Fix chin up bar-12 fastening on upper plate-13 using M10x80 hexagon bolt-24, Φ10 washer-
11 and M10 lock nut-10

Assembly step（3）explosion drawing
11
33 11
26
34
10
36
42
37
35 40
39 38
25
25
27
29
28
30
31
32
29
41
33
10
33
10
11
43
43
28
33
26
30
38
89
27
26
34
25
27
No. Descripon Note Qty. No. Descripon Note Qty.
10 lock nut M10 8 34 socket set screw M8*10 2
11 washer Φ10 16 35 end cap 2
25 lower base 2 36 check ring 2
26 upper base 2 37 pipe Φ2
27 guide rodΦ25*1850 2 38 buon head socket M12*40 2
28 lock sleeve 2 39 spring washer Φ12 2
29 sliding sleeve 2 40 washer Φ12 2
30 rubber pad with groove Φ60*Φ26*45 2 41 barbell rod 1
31 safety hook right 1 42 inner pipe Φ2
32 safety hook le1 43 rubber pad Φ60*Φ26*25 2
33 hexagon bolt M10*90 8 89 barbell rod ring 2

Assembly step（3）drawing
12
Assembly step（3）assembly instrucon
Installation
order
picture
UP Down
UP Down
1 Install 1 x side first and fit bar.
2 Fix lower base-25 fastening on lower plate using M10x90 hexagon bolt-33, Φ10 washer-11 and M10
lock nut-10
3 Fix upper base-26 fastening on upper plate using M10x90 hexagon bolt-33, Φ10 washer-11 and M10
lock nut-10
4 Guide rod in turn through lock sleeve-28, sliding sleeve-29, rubber pad-43, safety hook le-32 and
rubber pad with groove-30 fastening on base using M8x10socket set screw-34
aenon: the guide rod should be place upright
5 Barbell rod-41 in turn through sliding sleeve-29, check ring-36, inner pipe-42, pipe-37 and end cap-35
fastening using M12x40 buon head socket screw-38, Φ12 spring washer-39 and Φ12 washer-40,
then fit on barbell clamp collar-89
6 Guide rod in turn through lock sleeve-28, sliding sleeve-29, rubber pad-43, safety hook right-31 and
rubber padwith groove-30 fastening on base using M8x10socket set screw-34

Assembly step（4）explosion drawing
13
39
44
52
50
55
47
48
49
53
40
51
10
45 11
54
51
10
11
47
46
No. Descripon Note Qty.
10 lock nut M10 2
11 washer Φ10 7
39 spring washer Φ12 4
40 washer Φ12 4
44 upper connecon tube 1
45 lower connecon tube 1
46 big sliding sleeve 1
47 guide rod hollow 2
48 rubber pad Φ60*Φ26*45 2
49 hexagon bolt M10*25 2
50 hexagon bolt M10*95 1
51 hexagon bolt M10*55 2
52 hexagon bolt M12*30 4
53 double pulley bracket 1
34 socket set screw M8*10 2
55 back barbell plate holder 2

14
Assembly step（4）drawing
Assembly step（4）assembly instrucon
1Fix upper connecon tube short-44 fastening on main frame using M12x30 hexagon bolt-52,
Φ12 spring washer-39 and Φ12 washer-40
2
Fix lower connecon tube-45 fastening on main frame using M12x30 hexagon bolt-52, Φ12
spring washer-39 and Φ12 washer-40
3Fix double pulley bracket-53 fastening on double pulley bracket-45 using M10x55 hexagon
bolt-51, Φ10 washer-11 and M10 lock nut-10
4Guide rod hollow-47 in turn through big sliding sleeve-46, rubber pad-48 fastening using
M10x95 hexagon bolt-50, Φ10 washer-11 and M10x25 hexagon bolt-49
5Fix back barbell plate holder-55 fastening on big sliding sleeve-46 using M8x10 socket set
screw-34

Assembly step（5）explosion drawing
15
Wire port
outside of
sliding sleeve
56
49
11
10
59
60
49
60
57
58
60
58
10
59
10
60
61
58
Hand ghten first.
Do not over ghten
No. Descripon Note Qty.
10 lock nut M10 6
11 washer Φ10 14
49 hexagon bolt M10*25 2
56 wire Φ5*2745mm 2
57 pulley Φ95 6
58 pulley plate 4
59 hexagon bolt M10*45 2
60 hexagon bolt M10*50 4
61 weight 2

16
Assembly step（5）drawing
Assembly step（5）assembly instrucon
1
Connect wire-56 with weight-61, put them intoupring frame
2Fix pulley-57 fastening on upper bending tube using M10x50 hexagon bolt-60, pulley plate-
58, Φ10 washer-11 and M10 lock nut-10
3Fix pulley-57 fastening on upper bending tube using M10x45 hexagon bolt-59, pulley plate-
58, pulley plate-Φ58,10 washer-11 and M10 lock nut-10
4Fix wire-56 fastening on sliding sleeve outside using M10x25 hexagon bolt-49, Φ10 washer-
11 and M10 lock nut-10

Assembly step（6）explosion drawing
17
10
11
57
59
62
63
65
64
49
66
59
10
59
59
57
57
49
No. Descripon Note Qty.
10 lock nut M10 5
11 washer Φ10 12
49 hexagon bolt M10*25 2
57 pulley Φ95 5
59 hexagon bolt M10*45 5
62 wire 4740mm 1
63 "-" shaped pulley frame 1
64 short bar 1
65 footplate 1
66 chain + 2 snap hook 1

18
Assembly step（6）drawing
Assembly step（6）assembly instrucon
1
As the shown in the figure fix pulley-57 fastening on main frame and ”-“ shape pulley
frame-63 using M10x45 hexagon bolt-59, pulley plate-58, Φ10 washer-11 and M10 lock nut-
10
2
As the shown in the figure put the wire-62
3
Connect short bar-64 towire using chain + 2 snap hook-66
4
Fix footplate-65 fastening on main frame using M10x25 hexagon bolt-49, Φ10 washer-11
and M10 lock nut-10

Assembly step（7）explosion drawing
19
67
49
11
10
24
24 49
24
68
24
59
63
57
57
Wire needs to keep vertical
No. Descripon Note Qty.
10 lock nut M10 8
11 washer Φ10 16
24 hexagon bolt M10*80 4
49 hexagon bolt M10*25 2
57 pulley Φ95 6
59 hexagon bolt M10*45 2
63 "-" shaped pulley frame 2
67 wire Φ5*4095mm 2
68 pulley spacer sleeve Φ8

20
Assembly step（7）drawing
Assembly step（7）assembly instrucon
Internal wire schematic
1 Tofeed cable through frame.
2 As the shown in the figure fix pulley-57 fastening on upper plate using M10x80 hexagon bolt-
24, Φ10 washer-11 and M10 lock nut-10 and pulley spacer sleeve-68
3 Fix pulley-57 fastening on ”-“ shape pulley frame-63 using M10x45 hexagon bolt-59, Φ10
washer-11 and M10 lock nut-10
4 As the shown in the figure put the wire-67 using M10x45 hexagon bolt-59, Φ10 washer-11
and M10 lock nut-10 fastening on bending tube, careful tokeep the wire vercal

Assembly step（8）explosion drawing
21
10
11
59 57
69
70
71
No. Descripon Note Qty.
10 lock nut M10 2
11 washer Φ10 1
57 pulley Φ95 1
59 hexagon bolt M10*45 1
69 pulley frame 1
70 wire Φ5*1705mm 1
71 5 secon chain + snap 1