Organized Living freedomRail File Drawer OBox User manual

Lock and Key
freedomRail Assembly Instructions
File Drawer OBox
Contents of Package Tools Required
Power Drill
#2 Phillips
Screwdriver
Left Side
of OBox
(Inside View)
File Drawer Back
(Inside View)
Small Drawer Back
(Inside View)
Drawer Bottom
File Drawer
Right Side
File Drawer
Left Side
Small
Drawer
Right
Side
Small Drawer Front
File Drawer Front
(4)
(2) Drawer Pulls
Machine Screws
(For Drawer Pulls)
(4) Full Extension Drawer Glides
(32) Euroscrews (4) 1 /" Wood Screws
(12) Connector Bolts Hanging
Brackets
(2)
Right Side
of OBox
(Inside View) Top
(Inside View)
Small
Drawer
Left
Side
Bottom
(Inside View)
#2 Phillips Driver
(2) File Folder Bars
O-Ring
Assembling the File Drawer OBox
Step 1: Attach Hanging Brackets Step 2: Install Connector Bolts
Left Side Right Side
Back Edge Back Edge
Bottom
Install (4) Connector Bolts into small holes on Top and Bottom.
Step 3: Attach Sides
Cam
Lock
Open
(a) Attach Top. (b) Tighten Cams same as in Step 3.
(c) Place O-Ring over Lock from top and attach Lock with (2) Euroscrews.
Step 4: Attach Top and Locking Mechanism
Attach Hanging Brackets to Sides using Euroscrews. (If using power drill, set torque to low setting.)
Top
Smaller Holes for
Connector Bolts
1
Over
(a) Attach Sides to Bottom. (b) Lock Cam by turning clockwise until snug.
O-Ring
Proper Care for an OBox: Use Goo Gone™ or Simple Green® with a rag or putty knife to remove any excess glue or marring that was caused by shipping or assembly.
AlignArrowWithHole.

Mount OBox onto Uprights by inserting Hanging Brackets into the innermost track of each Upright.
freedomRail Assembly Instructions
File Drawer OBox
Installing Glides
Assembling Small Drawer
Assembling File Drawer
Step 5: Separate Glides Outer Glide Black Tab Inner Glide
Bumper
(a) Pull out Inner Glide to expose Black Tab. (b) Separate Inner Glide from Outer Glide by pushing the Black Tab while pulling Glide sections apart.
Attaches to OBox
Attaches to Drawer
Step 6: Attach Outer Glides to OBox
Turn OBox on its side. Attach Outer Glides with Euroscrews.
Install Outer Glides in holes 1 and 4. Repeat for other side.
(a) Attached Sides to Back.
(b) Secure with 1/" Wood Screws. (c) Slide in Bottom Panel.
(a) Screw in Connector Bolts and attach Front. (a) Lock Cam by turning clockwise / turn. Turn until
snug. (b) Attach Inner Glides to Drawer with Euroscrews.
Notched End should be at back. (c) Attach Drawer Pull
with Machine Screws.
(a) Lock Cam by turning clockwise / turn. Turn until
snug. (b) Attach Inner Glides to Drawer with Euroscrews.
Notched End should be at back. (c) Attach Drawer Pull
with Machine Screws.
(a) Screw in Connector Bolts and attach Front.
(a) Attach Sides to Back. (b) Insert File Folder Bars.
(c) Secure with 1/" Wood Screws.
Position Small Drawer on top set of Glides and push in Drawer completely. Position File Drawer on lower set of Glides and push in Drawer completely.
Step 9: Attach Front Panel Connectors
Inserting Drawers
Step 8: Attach Drawer Panels
Notched
End
Step 11: Attach Drawer Panels
Step 14: Insert Small Drawer Step 15: Insert Small Drawer
OrganizedLiving.com
1-800-669-3225
June 2018
7315-0524
©2018 Organized Living
Bloomington, IN 47403
2
Notched
End
Step 12: Attach Front Panel Connectors Step 13: Attach Glides and Pull
Step 10: Attach Glides and Pull
Step 7: Mount OBox on Uprights
OBox Front
Bumper
1
2
5
6
4
3