Organized Living freedomRail User manual

freedomRail®
THE TRULY ADJUSTABLE STORAGE SYSTEM.
1 2 3
INSTALLATION IS AS EASY AS…
freedomRail oers the exibility to change components, without any tools.
Install the Rail Place the Uprights
and add the Brackets
Add the Components
CLOSET DESIGN PARTS LIST — CHOCOLATE PEAR
Part Number Description Quantity
7913-4448-45 48" Rail - Nickel 1
7913-9137-11 Rail Screws & Anchors 1
7913-3548-45 48" Upright - Nickel 2
7913-1413-45 12 ½" Wood Shelf Bracket - Nickel 4
7913-1500-34 Rod Clip - Chrome 4
7913-1548-34 48" Clothes Rod - Chrome 2
7913-1510 -34 Rod Stop - Chrome 2
7313-1448-28 48" X 14" Wood Shelf - CP 2
7913-9168-40 Shelf-Loc 1
Contact Us.
Connect with us. ©2018 OrganizedLiving | Cincinnati, OH 45241
PARTS LIST
INSTALLATION GUIDE
Phone: [phone] am-5 pm EST Mon-Fri.
Email: [email protected]
organizedliving.com/installation

CLOTHES ROD AND ROD STOPS
• Spin the ange on the Rod Stop until it is halfway up
threaded shaft.
• Push Rod Stop into Rod; then twist the Rod Stop until it tightens.
• Place completed Rods onto Rod Clips.
Pull downward until they snap into place.
WOOD SHELVING
• Shelf-Locs attach Shelves to Wood Brackets.
• Place two Shelf-Locs into each Bracket facing up.
Remove paper tab.
• Place Shelf onto Bracket in desired position and press to
adhere to Shelf-Locs.
• Shelves may extend up to 9” beyond Bracket.
RAIL
• Measure 84” from the oor. Use a level
to draw a level line at this height.
• Center the Rail on the wall so the line is
visible through the mounting holes.
Draw a circle at each hole.
• Drill each hole with a ⁄” drill bit. If you do hit studs, use a ⁄”
drill bit to make a pilot hole. In this case, you will use the screw
only – no anchor needed.
• Tap plastic anchors into ⁄” holes. Place Rail over anchors.
• Insert and tighten all screws with a
power drill. IMPORTAN T: Allow screw
to turn 6-8 full rotations after it’s ush
with the Rail so the anchor tightens
into a ball behind the drywall.
• Place cover stickers over each screw head.
UPRIGHTS AND BRACKETS
• Insert Uprights onto the Rail at appropriate spacing intervals.
• Insert Brackets into Uprights at appropriate shelf heights
ROD CLIPS
• Rod Clips are placed into Brackets prior to installing shelves.
• Insert Rod Clips into the Bracket and pull downward until you
feel it snap into place.
INSTALLATION GUIDELINES
Power Drill
Phillips Driver
Tape Measure
Level
/" Bit
/" Bit Pencil
TOOLS YOU WILL NEED
Learn how to install freedomRail
like an expert!
organizedliving.com/installation
UPC 46964026403 | 880108 | 7903-0148-28
UPRIGHT
BRACKET
RAIL
CLOTHES ROD
ROD STOP
SHELF-LOC
ROD CLIP
OBOXES AND REVEAL ACCESSORIES
• Uprights are spaced 24” apart for OBoxes or Reveal
accessories.
Insert the bracket into the inside slot of each Upright.
• If stacking OBoxes or Reveal accessories, install the bottom
one rst.
• If placing any accessory next to an OBox, an additional
Upright is required.
• If placing two Reveal accessories side-by-side the
accessories can share a singe Upright.
b