ORiNG TRGPS-9084TG-M12X-BP2-MV User manual

T
TR RG GP PS S- -9 90 08 84 4T TG G- -M M1 12 2X X- -B BP P2 2- -M MV V
I
In nd du us st tr ri ia al l R Ra ac ck k- -M Mo ou un nt t E Et th he er rn ne et t S Sw wi it tc ch h
U
Us se er r M Ma an nu ua al l
V
Ve er rs si io on n 1 1. .0 0
J
Ja an n, , 2 20 01 19 9
w
ww ww w. .o or ri in ng gn ne et t. .c co om m

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
1
COPYRIGHT NOTICE
Copyright © 2014 ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and workmanship for
a specified warranty period from the invoice date (5 years for most products). ORing will repair
or replace products found by ORing to be defective within this warranty period, with shipment
expenses apportioned by ORing and the distributor. This warranty does not cover product
modifications or repairs done by persons other than ORing-approved personnel, and this
warranty does not apply to ORing products that are misused, abused, improperly installed, or
damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be responsible for its
use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. ORing reserves the right to revise the contents of this
publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
3F., NO.542-2, Jhongjheng Rd., Sindian District, New Taipei City 231, Taiwan, R.O.C.
Tel: + 886 2 2218 1066 // Fax: + 886 2 2218 1014
Website: www.oringnet.com
Technical Support
E-mail: [e-mail]
Sales Contact
E-mail: [email protected]om (Headquarters)
[e-mail] (China)

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
2
Table of Content
Getting Started...............................................................................................6
1.1 About the TRGPS-9084TG-M12X-BP2-MV....................................................................6
1.2 Software Features ..............................................................................................................6
1.3 Hardware Specifications ....................................................................................................7
Hardware Overview........................................................................................8
2.1 Front Panel ..........................................................................................................................8
2.2 Front Panel LED .................................................................................................................9
2.3 Bypass Technology...........................................................................................................10
Hardware Installation...................................................................................11
3.1 Rack-mount Installation ...................................................................................................11
3.2 Wiring..................................................................................................................................12
3.2.1 Grounding..........................................................................................................................12
3.2.2 Fault Relay.........................................................................................................................12
3.2.3 Redundant Power Inputs.................................................................................................13
3.3 Connection.........................................................................................................................14
3.3.1 Cables ................................................................................................................................14
3.3.2 O-Ring/O-Chain ................................................................................................................16
Redundancy .................................................................................................20
4.1 O-Ring................................................................................................................................20
4.1.1 Introduction........................................................................................................................20
4.1.2 Configurations...................................................................................................................20
4.2 OPEN-Ring........................................................................................................................22
4.2.1 Introduction........................................................................................................................22
4.2.2 Configurations...................................................................................................................22
4.3 O-Chain..............................................................................................................................23
4.3.1 Introduction........................................................................................................................23
4.3.2 Configurations...................................................................................................................23
4.4 Bypass................................................................................................................................24
4.4.1 Introduction........................................................................................................................24
4.4.2 Bypass & Ring Topology..................................................................................................25
4.5 MRP (*NOTE) .........................................................................................................................27
4.5.1 Introduction........................................................................................................................27
4.5.2 Configurations...................................................................................................................27

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
3
4.6 STP/RSTP/MSTP.............................................................................................................28
4.6.1 STP/RSTP .........................................................................................................................28
4.6.2 MSTP..................................................................................................................................31
4.6.3 CIST....................................................................................................................................34
4.7Fast Recovery...................................................................................................................36
Management.................................................................................................38
6.1 Basic Settings......................................................................................................... 40
6.1.1 System Information ................................................................................................ 40
6.1.2 Auth Method .................................................................................................. 41
6.1.3 Users ............................................................................................................. 42
6.1.4 IP Settings ..................................................................................................... 45
6.1.5 IP Status ........................................................................................................ 48
6.1.6 Daylight Saving Time..................................................................................... 49
6.1.7 HTTPS........................................................................................................... 51
6.1.8 SSH ............................................................................................................... 52
6.1.9 DBU01 Option Config.................................................................................... 52
6.1.10 LLDP ......................................................................................................... 53
6.1.11 NTP ........................................................................................................... 57
6.1.12 Upnp.......................................................................................................... 58
6.1.13 ModbusTCP .............................................................................................. 59
6.1.14 Ethernet/IP ................................................................................................ 59
6.1.15 Backup/Restore Configurations ................................................................ 60
6.1.16 Firmware Update....................................................................................... 60
6.2 DHCP................................................................................................................. 61
6.2.1 DHCP Server................................................................................................. 61
6.2.2 DHCP Relay .................................................................................................. 65
6.2.3 DHCP Snooping ............................................................................................ 68
6.3 Port Setting ........................................................................................................ 71
6.3.1 Port Control.................................................................................................... 71
6.3.2 Port Trunk...................................................................................................... 74
6.3.3 Loop Protection ............................................................................................. 79
6.4 VLAN...................................................................................................................... 80
6.4.1 VLAN Membership ........................................................................................ 80
6.4.2 Membership Status........................................................................................ 85
6.4.3 Port Status..................................................................................................... 86
6.4.4 Private VLAN................................................................................................. 87
6.4.5 GVRP............................................................................................................. 89

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
4
6.5 SNMP..................................................................................................................... 91
6.5.1 SNMP System Configurations....................................................................... 91
6.5.2 Trap................................................................................................................ 92
6.5.3 SNMP Community Configurations................................................................. 94
6.5.4 SNMP User Configurations ........................................................................... 95
6.5.5 SNMP Group Configurations......................................................................... 96
6.5.6 SNMP View Configurations ........................................................................... 97
6.5.7 SNMPAccess Configurations........................................................................ 98
6.5.8 RMON............................................................................................................ 99
6.6 Traffic Prioritization............................................................................................... 106
6.6.1 Storm Control............................................................................................... 106
6.6.2 Port Classification........................................................................................ 108
6.6.3 Port Tag Remaking...................................................................................... 109
6.6.4 Port DSCP....................................................................................................110
6.6.5 Port Policing..................................................................................................111
6.6.6 Queue Policing .............................................................................................112
5.6.7 QoS Egress Port Scheduler and Shapers....................................................112
5.6.8 Port Scheduler..............................................................................................115
5.6.9 Port Shaping.................................................................................................115
5.6.10 DSCP-Based QoS....................................................................................116
5.6.11 DSCP Translation.....................................................................................117
5.6.12 DSCP Classification.................................................................................118
5.6.13 QoS Control List.......................................................................................118
5.6.14 QoS Statistics( QoS Counters)................................................................ 121
5.6.15 QCL Status.............................................................................................. 121
5.6.16 WRED ..................................................................................................... 123
6.7 Multicast ............................................................................................................... 125
6.7.1 IGMP Snooping ........................................................................................... 125
6.7.2 MVR............................................................................................................. 130
6.8 Security ................................................................................................................ 135
6.8.1 Device Binding............................................................................................. 135
6.8.2 Access Management................................................................................... 140
6.8.3 IP Source Guard.......................................................................................... 141
6.8.4 ACL.............................................................................................................. 143
6.8.5 AAA.............................................................................................................. 155
6.8.6 TACACS+ .................................................................................................... 156
6.8.8 NAS (802.1x)............................................................................................... 159

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
5
6.8.9 ARP Inspecition........................................................................................... 170
6.8.10 Port Security............................................................................................ 172
6.9 Warning................................................................................................................ 176
6.9.1 Fault Alarm................................................................................................... 176
6.9.2 System Warning .......................................................................................... 176
6.10 Monitor and Diag.................................................................................................. 178
6.10.1 MAC Table............................................................................................... 178
6.10.2 Port Statistics........................................................................................... 182
6.10.3 Port Monitoring........................................................................................ 184
6.10.4 System Log Information .......................................................................... 185
6.10.5 Cable Diagnostics ................................................................................... 187
6.10.6 Ping ......................................................................................................... 188
IPv6 Ping .................................................................................................................. 188
6.11 POE...................................................................................................................... 189
6.11.1 Configuration........................................................................................... 189
6.11.2 Status ...................................................................................................... 191
6.12 Configuration........................................................................................................ 193
6.12.1 Activate.................................................................................................... 193
6.12.2 Delete...................................................................................................... 193
6.13 Save ..................................................................................................................... 193
6.14 Troubleshooting.................................................................................................... 193
6.14.1 Factory Defaults ...................................................................................... 193
6.14.2 System Reboot........................................................................................ 194
Technical Specifications ...........................................................................195

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
6
Getting Started
1.1 About the TRGPS-9084TG-M12X-BP2-MV
ORing’s TransporterTM series managed Ethernet switches are designed for industrial
applications such as rolling stock, vehicle, and railway. The TRGPS-9084TG-M12X-BP2-MV,
which is compliant with the EN50155 standard, is a managed 10G/2.5G Redundant Ring
Ethernet switch with 8x10/100/1000Base-T(X) P.S.E. ports and 4x10GBase-T ports which is
specifically designed for the toughest and fully compliant with EN50155 requirement. The
switch support Ethernet Redundancy protocol, O-Ring (recovery time < 30ms over 250 units of
connection), O-Chain, MRP and MSTP (RSTP/STP compatible) can protect your
mission-critical applications from network interruptions or temporary malfunctions with its fast
recovery technology. It is specifically designed for the toughest industrial environments.
TRGPS-9084TG-M12X-BP2-MV EN50155 Ethernet switch uses M12 connectors to ensure
tight, robust connections, and guarantee reliable operation against environmental disturbances,
such as vibration and shock. TRGPS-9084TG-M12X-BP2-MV also support Power over
Ethernet, a system to transmit electrical power up to 30 watts, along with data, to remote
devices over standard twisted-pair cable in an Ethernet network. Each
TRGPS-9084TG-M12X-BP2-MV switch has 8x10/100/1000Base-T(X) P.S.E. (Power Sourcing
Equipment) ports. P.S.E. is a device (switch or hub for instance) that will provide power in a
PoE connection. And support wide operating temperature from -20 oC to 60 oC.
TRGPS-9084TG-M12X-BP2-MV can also be managed centralized and convenient by
Open-Vision, Except the Web-based interface, Telnet and console (CLI) configuration.
Therefore, the switch is one of the most reliable choice for highly-managed and Ethernet
application.
1.2 Software Features
Supports O-Ring (recovery time < 30ms over 250 units of connection) and
MSTP(RSTP/STP compatible) for Ethernet Redundancy
Supports O-Chain that allows the device to operate in multiple redundant ring topologies
Supports IEEE 802.3af/at compliant PoE and total power budget is 60Watts with
maximum 15.4/30Watts per port
Supports PoE scheduled configuration and PoE auto-ping check
Support IEEE 1588v2 clock synchronization
Supports IPv6 new Internet protocol version
Supports Modbus TCP protocol
HTTPS/SSH protocols for higher network security

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
7
Supports IEEE 802.3az Energy-Efficient Ethernet technology
Supports SMTP client
Supports IP-based bandwidth management
Supports application-based QoS management
Supports Device Binding security
Supports DOS/DDOS auto prevention
IGMP v2/v3 (IGMP snooping support) for filtering multicast traffic
Supports SNMP v1/v2c/v3 & RMON & 802.1Q VLAN network management
Supports ACL, TACACS+ and 802.1x user authentication
Supports 9.6K bytes Jumbo frame
Multiple notifications during unexpected events
Configuration via Web-based ,Telnet, Console (CLI), and Windows utility (Open-Vision)
Supports LLDP Protocol
1.3 Hardware Specifications
8x10/100/1000Base-T(X) P.S.E. M12 ports (provide up to 30 Watts per port)
4 x 100/1G/2.5G/10G Base-T(X) M12 ports
1 x console port
2 sets of bypass ports
EN50155-compliance
Operating temperature: -40 to 70oC
Storage temperature: -40 to 85 oC
Operating humidity: 5% to 95%, non-condensing
Casing: IP-40
Dimensions: 440(W)x325(D)x44(H)mm

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
8
Hardware Overview
2.1 Front Panel
The device provides the following ports on the front panel. Ethernet ports use M12 X-Code
type , Console and relay ports use M12 A-Code type , to ensure tight, robust connections, as
well as reliable operation against environmental disturbances, such as vibration and shock.
Port
Description
Power
connector
1 x power connector
Ethernet ports
8 x 10/100/1000Base-T(X) P.S.E. copper ports(M12 X-Code)
4 x 100/1G/2.5G/ 10G Base-T(X) non-PoE ports with bypass
function(M12 X-Code)
Console
1 x console port (M12 A-Code)
Relay output
1 x relay output (M12 A-Code)
Reset button
1 x reset button
1. Reset button
2. System LED
PWR LED
R.M status LED
Ring status LED
Fault LED
3. Power connector
4. Non-PoE
100/1G/2.5G/10G-Ethernet
ports with bypass
5. PoE-enabled Gigabit Ethernet ports
6. Link/ACT LED for non-PoE Gigabit ports
7. Speed LED for non-PoE Gigabit ports
8. PoE Port LED
Link/ACT LED for PoE-enabled Gigabit ports
PoE indicator for PoE-enabled Gigabit ports
Speed LED for PoE-enabled Gigabit ports
9. Console port
10. Relay output

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
9
2.2 Front Panel LED
LED
Color
Status
Description
PWR
Green
On
DC power module 1 activated
R.M
Green
On
Device operating in Ring Master mode
Ring
Green
On
Ring enabled
Blinking
Ring structure is broken
Fault
Amber
On
Errors occur (i.e. power failure or port
malfunctioning)
10/100/1000Base-T(X) P.S.E Ethernet ports
LNK/ACT
Green
On
Port is linked
Blinking
Transmitting data
PoE
Green
On
Power supplied over Ethernet
Speed
Green
On
Port is running at 1000Mbps
Amber
On
Port is running at 100Mbps
OFF
Port is running at 10Mbps
100/1G/2.5G/10G Base-T(X) Ethernet ports
LNK/ACT
Green
On
Port is linked
Blinking
Transmitting data
Speed
Green
On
Port is running at 1000Mbps
Amber
On
Port is running at 100Mbps
OFF
Port is running at 10Mbps

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
10
2.3 Bypass Technology
When a device connected to other devices through a switch without bypass function, the
device will lose connection if he switch loses power as traffic will not be able to flow through the
link (as shown in the figure below).
Switches with bypass functions such as the TRGPS-9084GT-M12X-BP2-MV provide one or
more sets of bypass ports that ensure constant network connectivity during power failure.

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
11
Hardware Installation
3.1 Rack-mount Installation
Rack-mount Measurement (Unit = mm)
Follow the following steps to install the switch to a rack.
Step 1: Attach the mounting brackets to the front left and right sides of the switch using 4
screws
Step 2: With front brackets orientated in front of the rack, fasten the brackets to the rack using
two more screws.
Instead of screwing the screws in all the way, it is advised to leave a space of about
2mm to allow room for sliding the switch between the wall and the screws.

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
12
3.2 Wiring
ATTENTION
1. Be sure to disconnect the power cord before installing and/or wiring your
switches.
2. Calculate the maximum possible current in each power wire and common wire.
Observe all electrical codes dictating the maximum current allowable for each
wire size.
3. If the current goes above the maximum ratings, the wiring could overheat,
causing serious damage to your equipment.
4. Use separate paths to route wiring for power and devices. If power wiring and
device wiring paths must cross, make sure the wires are perpendicular at the
intersection point.
5. Do not run signal or communications wiring and power wiring through the same
wire conduit. To avoid interference, wires with different signal characteristics
should be routed separately.
6. You can use the type of signal transmitted through a wire to determine which
wires should be kept separate. The rule of thumb is that wiring sharing similar
electrical characteristics can be bundled together
7. You should separate input wiring from output wiring
8. It is advised to label the wiring to all devices in the system
3.2.1 Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection on the power connector to the grounding surface prior to
connecting devices.
3.2.2 Fault Relay
The switch uses the M12 A-coded 5-pin male connector on the front panel for relay output. Use
a power cord with an M12 A-coded 5-pin female connector to connect the relay contacts from
the switch. The relay contacts will detect user-configured events and form an open circuit when
an event is triggered.
WARNING
Do not disconnect modules or wires unless power has been switched off or
the area is known to be non-hazardous. The devices may only be connected
to the supply voltage shown on the type plate.

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
13
.
3.2.3 Redundant Power Inputs
The switch provides two sets of power supply on a M23 5-pin connector to enable dual power
inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is achieved. Make sure
the connection is tight.

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
14
3.3 Connection
3.3.1 Cables
10/100/1000BASE-T(X) PIN ASSIGNMENTS
The device provides Ethernet ports in M12 connector type. According to the link type, the
switch uses CAT 3, 4, 5,5e UTP cables to connect to any other network devices (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable specifications.
8-Pin Gigabit Port Definition
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
M12 X-coding
connector
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
M12 X-coding
connector
1000BASE-T
Cat. 5/Cat. 5e 100-ohm
UTP
UTP 100 m (328ft)
M12 X-coding
connector
Pin No.
Description
#1
BI_DA+
#2
BI_DA-
#3
BI_DB+
#4
BI_DB-
#5
BI_DD+
#6
BI_DD-
#7
BI_DC-
#8
BI_DC+

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
15
Below is the pin assignment for the Ethernet ports.
10/100/1000Base-T(X) M12 port
Pin Number
Assignment
#1
BI_DC+
#2
BI_DD+
#3
BI_DD-
#4
BI_DA-
#5
BI_DB+
#6
BI_DA+
#7
BI_DC-
#8
BI_DB-
10/100/1000Base-T(X) P.S.E. M12 port
Pin Number
Assignment
#1
BI_DC+
#2
BI_DD+
#3
BI_DD-
#4
BI_DA- with PoE Vout+
#5
BI_DB+ with PoE Vout-
#6
BI_DA+ with PoE Vout+
#7
BI_DC-
#8
BI_DB- with PoE Vout-
The device supports auto MDI/MDI-X operation. You can use a cable to connect the switch to a
PC. The table below shows the 10/100Base-T(X) MDI and MDI-X port pin outs.
10/100 Base-T(X) MDI/MDI-X Pin Assignments:
Pin Number
MDI port
MDI-X port
1
TD+(transmit)
RD+(receive)
2
TD-(transmit)
RD-(receive)
3
RD+(receive)
TD+(transmit)
4
Not used
Not used
5
Not used
Not used
6
RD-(receive)
TD-(transmit)
7
Not used
Not used
8
Not used
Not used

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
16
1000Base-T MDI/MDI-X PinAssignments:
Pin Number
MDI port
MDI-X port
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.
Console port wiring
The switch has one RS-232 (M12 5pin) console port, located on the front panel. Use a
M12-to-DB9 console cable to connect the console port to your PC's COM port.
3.3.2 O-Ring/O-Chain
O-Ring
You can connect three or more switches to form a ring topology to gain network redundancy
capabilities through the following steps.
1. Connect each switch to form a daisy chain using an Ethernet cable.
2. Set one of the connected switches to be the master and make sure the port setting of each
connected switch on the management page corresponds to the physical ports connected. For
information about the port setting, please refer to 4.1.2 Configurations.
3. Connect the last switch to the first switch to form a ring topology.

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
17
Coupling Ring
If you already have two O-Ring topologies and would like to connect the rings, you can form
them into a coupling ring. All you need to do is select two switches from each ring to be
connected, for example, switch A and B from Ring 1 and switch C and D from ring 2. Decide
which port on each switch to be used as the coupling port and then link them together, for
example, port 1 of switch A to port 2 of switch C and port 1 of switch B to port 2 of switch D.
Then, enable Coupling Ring option by checking the checkbox on the management page and
select the coupling ring in correspondence to the connected port. For more information on port
setting, please refer to 4.1.2 Configurations. Once the setting is completed, one of the
connections will act as the main path while the other will act as the backup path.

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
18
Dual Homing
If you want to connect your ring topology to a RSTP network environment, you can use dual
homing. Choose two switches (Switch A & B) from the ring for connecting to the switches in the
RSTP network (core switches). The connection of one of the switches (Switch A or B) will act
as the primary path, while the other will act as the backup path that is activated when the
primary path connection fails.

TRGPS-9084TG-M12X-BP2-MV User Manual
ORing Industrial Networking Corp
19
O-Chain
When connecting multiple O-Rings to meet your expansion demand, you can create an
O-Chain topology through the following steps.
1. Select two switches from the chain (Switch A & B) that you want to connect to the O-Ring
and connect them to the switches in the ring (Switch C & D).
2. In correspondence to the port connected to the ring, configure an edge port for both of the
connected switches in the chain by checking the box in the management page (see 4.1.2
Configurations).
3. Once the setting is completed, one of the connections will act as the main path, and the
other as the backup path.