ORiNG IES-180-L User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
QIG IES-180-L 1907-2-29-IES180L-1.0
IES-180-L is an unmanaged Ethernet switch with eight 10/100Base-T(X)
ports in a compact form factor. The easy-to-install switch comes with rigid
IP-30 housing and can operate in harsh environments. The wide operating
temperature range from -20 C to 60 C ensures the switch can operate reliably
in extreme weather conditions.
oo
Package Contents
Installation
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed cabinet, the operating
ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
Installation of the equipment should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
Mounting of the equipment in the d should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
in-rail
Safety & Warnings
Contents
Wall-mount Kit
DIN-rail Kit
IES-180-L
Pictures Number
X2
X1
QIG X1
Dimension (Unit: mm)
Panel Layouts
Front Panel
1. PWR LED
2. Link/Act indicator for LAN port
3. LAN port
IES-180-L
X1
1
3
2
Top Panel
1. Terminal block
Real Panel
1
1. Wall-mount screw holes
2. Din-rail screw holes
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into
the rail firmly.
DIN-rail Installation
Step 1:
Step 2:
Step 3:
Screw the two pieces of wall-mount kits onto both sides of the switch. A
total of eight screws are required, as shown below.
Use the switch, with wall mount plates attached, as a guide to mark the correct
locations of screws.
Insert screw through the large parts of the keyhole-shaped apertures, and then slide
the switch downwards. Tighten the four screws for added stability.
wall-mount
Wall-mounting
SWITCH
INDUSTRIAL
Industrial Unmanaged Switch
1
IES-180-L
P2
P4
P6
P1
P3
P5
V+ V-
DC10~ 30V
P8P7
PWR
10/100TX
LNK/ACT
SPEED
100M
10M
IES-180-L
P2
P4
P6
P1
P3
P5
P8P7
PWR
10/100TX
LNK/ACT
SPEED
100M
10M
25.00
37.00
V+ V-
DC10 ~ 30V
IES-180-L
P2
P4
P6
P1
P3
P5
P8P7
PWR
10/100TX
LNK/ACT
SPEED
100M
10M
IES-180-L
P2
P4
P6
P1
P3
P5
P8P7
PWR
10/100TX
LNK/ACT
SPEED
100M
10M
1
2
IES-180-L
P2
P4
P6
P1
P3
P5
P8P7
PWR
10/100TX
LNK/ACT
SPEED
100M
10M
IES-180-L
P2
P4
P6
P1
P3
P5
P8P7
PWR
10/100TX
LNK/ACT
SPEED
100M
10M

QIG Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
ORing Industrial Networking Corp.
Copyright© 2015 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
The switch provides a 10~30 VDC voltage power input on a 3-
pin terminal block. Follow the steps to connect the power.
Insert the negative/positive wires into the V-/V+
terminals, respectively.
To keep the DC wires from pulling loose, use a small
flat-blade screwdriver to tighten the wire-clamp screws on the
front of the terminal block connector.
STEP 1:
STEP 2:
Version 1.0
QIG
Configurations
After installing the switch and connecting cables, start the switch by
turning on power. The green power LEDs should turn on.and
LED indication table
Specifications
QIG
Wiring
ORing Switch Model IES-180-L
10/100Base-T(X) Ports in
RJ45 Auto MDI/MDIX 8
Physical Ports
Technology
Ethernet Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX
IEEE 802.3x for Flow control
Power
Input power
Power consumption(Typ.)
10~30 VDC voltage power input on 3-pin terminal block
1.65 Watts
Overload current protection
Reverse polarity protection
Present
Present
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH) 41(W)x75(D)x115(H)mm(1.61x2.95x4.53inch)
Weight (g)
Environmental
-40to85C(-40to185F)
oo
Storage Temperature
Operating Temperature
5% to 95% Non-condensingOperating Humidity
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class AEMI
EN61000-4-2 (ESD),
EN61000-4-3 (RS),
EN61000-4-4 (EFT),
EN61000-4-5 (Surge),
EN61000-4-6 (CS),
EN61000-4-8,
EN61000-4-11
EMS
IEC60068-2-27Shock
IEC60068-2-32
IEC60068-2-6Vibration
EN60950-1 Safety
Free Fall
Warranty
5years
Processing Store-and-Forward
307 g
-20to60C(-4to140F)
oo
MAC Table 2048 MAC addresses
Network Connection
The device has standard Ethernet ports. According to the link type, the switch uses CAT 3,
4, 5, 5e UTP cables to connect to any other network devices (PCs, servers, switches,
routers, or hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications:
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 1 00-ohm UTP 10 0 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
For pin assignments for the cables, please refer to the following table.
10/100Base- T(X) RJ-45
Pin Numb er Assignment
1TD+
2TD-
3RD+
4Notused
5Notused
6RD-
7Notused
8Notused
Note: “+” and “-” signs represent the polarity of the wires that
make up each wire pair.
QIG
SWITCH
INDUSTRIAL
Industrial Unmanaged Switch
Power inputs
V+ V-
LED Color Status Descr iption
PWR Green On DC power module activated
On Port is linked
Green
Blinking Transmitting data
On Port is running at 100Mbps
LNK/ACT
Amber
Off Port is running at 10Mbps
QIG IES-180-L
IES-180-L
Packet Buffer 448Kbits