ORiNG IGPS-1041GTA User manual

P1 P2 Fault
IGPS-1041GTA
3
4
10/100/1000T
1
2
5
Practical Operation
QIG Quick Installation Guide
IGPS-1041GTA
IGPS-1041GTA
Version 1.0
Quick Installation Guide
ORing Industrial Networking Corp.
Features
IGPS-1041GTA IGPS-
1041GTA
IGPS-1041GTA
is an unmanaged PoE Ethernet switch with P.S.E. function.
support Power over Ethernet, a system to transmit electrical power, along
with data, to remote devices over standard twisted-pair cable in an Ethernet
network. has 4X10/100/1000Base-T(X) P.S.E. (Power Sourcing
Equipment) ports. P.S.E. is a device (switch or hub for instance) that will provide
power in a PoE setup. The wide operating temperature range from -40 C to 70 C
can satisfy most of operating environment. Therefore, the switch is one of the most
reliable choices for PoE Ethernet application.
oo
Introduction Specifications
ORing Switch Model
Physical Ports
Technology
Ethernet Standards
LED Indicators
Green: Power LED x2Power indicator
10/100/1000Base-T(X) Port
in RJ45 Auto MDI/MDIX
IGPS-1041GTA
1
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX
IEEE 802.3ab for 1000Base-T
IEEE 802.3x for Flow control
IEEE 802.3at PoE specification (up to 30 Watts per port for P.S.E.)
MAC Table 2048 MAC addresses
Environmental
-40to85C(-40to185F)
oo
Storage Temperature
Operating Temperature
5% to 95% Non-condensingOperating Humidity
Regulatory approvals
FCC Part 15, CISPR (EN55022) class AEMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27Shock
IEC60068-2-32
IEC60068-2-6Vibration
Free Fall
Warranty
5 years
-40to70C(-40to158F)
oo
Amber:IndicatePWR1orPWR2failure
Fault indicator
Fault contact
Relay Relay output to carry capacity of 1A at 24 VDC
Power
Redundant Input power
Power consumption(Typ.) 6.1 Watts (Power device not included)
Overload current protection
Reverse polarity protection
Present
Not Present
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH)
Weight (g) 407g
Dual DC inputs 50VDC on 6-pin terminal block
26.1(W)x94.9(D)x144.3(H) mm (1.03x3.74x5.68inch.)
10/100/1000Base-T(X)
ndicator
RJ45
portandPoEi
Green on the left for port Link/Act.
Green on the right for PoE power injected.
IGPS-1041GTA can be used in connecting several PoE P.D. Ethernet devices like IP-
Camera or other Ethernet devices. In addition, there are two different power inputs
at terminal block to avoid interruption caused by power down. When the primary
DC power input fails, the backup power input will take over immediately to guarantee a
non-stop operation.
Industrial Unmanaged Gigabit PoE Switch
PRINTED ON RECYCLED PAPER
EN60950-1Safety
GIGABIT
INDUSTRIAL
SWITCH
Provide 4x10/100/1000Base-T(X) PoE (P.S.E.) ports
Support P.S.E. based on IEEE 802.3at standard up to 30 Watts per port
Support auto-negotiation and auto-MDI/MDI-X
Support store and forward transmission
Support flow control
Rigid IP-30 housing design
DIN-Rail and wall mounting enabled
Power Connection Guide
Frame Ground
PWR-1PWR-2
V2-V2+ V1-V1+
G
1A@24V DC 50-57V
Power
Supply
50 VDC
V+
V-
Warning
Device
GND+24V
V+
V-
DIP Switch Select for
Power Alarm Relay Output
Power
Supply
50 VDC
Power
Supply
DIP-2
OFF
OFF
ON
DIP-1
Power failure relay alarm disabled
PWR-1 failure, alarm enabledrelay
PWR-2 failure, alarm enabledrelay
DIP Switch Function
OFF
ON
OFF
Description
DIP-Switch
Power-1failedwarning:(ON)enable,(OFF)disableDIP-Switch 1
Power-2failedwarning:(ON)enable,(OFF)disable
DIP-Switch 2
Practical Operation
Power Fault LED
Power LED
A
Gigabit LAN Port
Green: PoE power injected
Green: Link/Act
PoE
ON PWR-1 or PWR-2 failure,
alarm enabledrelay
ON
10/100/1000Base-T(X) P.S.E.
Port with P.S.E. 4
Processing Store-and-Forward
1907-2-29-IGPS1041GT
Connections of Ethernet devices
10/100/1000Base-T(X)
ndicator
RJ45
port i
Green for port Link/Act.
Amer for duplex indicator.
Amer: Duplex indicator
Green: Link/Act

QIG Quick Installation Guide
PRINTED ON RECYCLED PAPER
Accessory Communication Connections
1000Base-T Ethernet Connection
RJ45 (8-pin, MDI) Port Pinouts
18
Pin MDI
1
2
3
4
5
6
7
8
BI_DA+
BI_DA-
BI_DB+
BI_DC+
BI_DC-
BI_DB-
BI_DD+
BI_DD-
RJ45 (8-pin, MDI-X) Port Pinouts
18
RJ45 (8-pin) to RJ45 (8-Pin) Straight-Through Cable Wiring
RJ45 Plug Pin1
Pin
Straight-Through Cable
Switch Port
RJ-45
Connector
Tx+
Tx-
Rx+
Rx-
3
6
1
2
NIC Port
RJ-45
Connector
Rx+
Rx-
Tx+
Tx-
3
6
1
2
RJ45 (8-pin) to RJ45 (8-Pin) Cross-Over Cable Wiring
RJ45 Plug Pin1
Cross-Over Cable
Switch Port
(NIC Port)
RJ-45
Connector
Tx+
Tx-
Rx+
Rx-
3
6
1
2
RJ-45
Connector
Rx+
Rx-
Tx+
Tx-
1
2
3
6
Switch Port
(NIC Port)
(Rx+)
(Rx-)
(Tx+)
(Tx-)
(Tx+)
(Tx-)
(Rx+)
(Rx-)
Pin MDI-X
1
2
3
4
5
6
7
8
BI_DB+
BI_DB-
BI_DA+
BI_DD+
BI_DD-
BI_DA-
BI_DC+
BI_DC-
Pin
Version 1.0
Quick Installation Guide
ORing Industrial Networking Corp.
Installation
DIN-Rail Install Step Wall-mounted Install Step
10/100Base-T(X) Ethernet Connection
GIGABIT
INDUSTRIAL
SWITCH
PoE
Industrial Unmanaged Gigabit PoE Switch
Dust Cover (RJ-45)
2
QIG
6
Round Screw (M3 X3)
3Wall-mounted kit (for Slim Type)
4
25mm DIN-Rail kit
5
6-Pin Terminal block
1
I1X1, 2X5, 3X8,
X1
X2,
A
IGPS-1041GTA
Model name Model Description Accessory
Front Panel
Industrial 5-port slim type unmanaged Gigabit
PoE Ethernet switch with
4x10/100/1000Base-T(X) P.S.E. and
1x10/100/1000Base-T(X)
6
4
5X1,
Packing list
ORing Industrial Networking Corp.
Copyright© 2011 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]
IGPS-1041GTA
IGPS-1041GTA
Pin Definition
10/100Base-T(X) PoE P.S.E.
Port
RJ45 Pin Definition
Pin No.
TD+ with PoE Power input +
#1
Description
#2
#3
#6
TD- with PoE Power input +
RD+ with PoE Power input +
RD- with PoE Power input -
1000Base-T PoE P.S.E. Port
RJ45 Pin Definition
Pin No.
BI_DA+ with PoE Power input +
#1
Description
#2
#3
#4
BI_DA- with PoE Power input +
BI_DB+ with PoE Power input -
BI_DC+
BI_DC-
#5
#6
#7
#8
BI_DB- with PoE Power input -
BI_DD+
BI_DD-