Practical Operation
QIG Quick Installation Guide
IGS-1042GPA
IGS-1042GPA
Version 1.2
Quick Installation Guide
Features
IGS-1042GPA is an unmanaged Ethernet switch, w 4x10/100/1000Base-T(X)
ports and 2x100/1000Base-X SFP port. The optical network speed SFP port can
be set by changing the settings of the DIP-Switch below. The wide operating
temperature range from -40 C to 70 C can satisfy most of operating environment.
Therefore, the switch is one of the most reliable choices for Ethernet application.
ith
of
oo
Introduction Specifications
IGS-1042GPA can be used in connecting several Ethernet devices like IP-Camera
or other Ethernet devices. In addition, there are two different power inputs at
terminal block to avoid interruption caused by power down. When the primary DC
power input fails, the backup power input will take over immediately to guarantee a
non-stop operation.
IGS-1042GPA provide 4x10/100/1000Base-T(X) ports
SFP port support 100Base-FX and 1000Base-X dual speed
Support auto-negotiation and auto-MDI/MDI-X
Support store and forward transmission
Support flow control
Rigid IP-30 housing design
DIN-Rail and wall mounting enabled
Power Connection Guide Front Panel
A
1907-2-29-IGS1042GPA-1.2
Connections of Ethernet devices
PRINTED ON RECYCLED PAPER
ORing Switch Model
Physical Ports
Technology
Ethernet Standards
LED Indicators
Green: Power LED x2Power indicator
10/100/1000Base-T(X) Port in
Rj45 Auto MDI/MDIX
IGS-1042GPA
4
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3ab for 1000Base-T
IEEE 802.3z for 1000Base-X
IEEE 802.3x for Flow control
MAC Table 1K MAC addresses
Environmental
-40to85C(-40to185F)
oo
Storage Temperature
Operating Temperature
5% to 95% Non-condensingOperating Humidity
Regulatory Approvals
FCC Part 15, CISPR (EN55022) class AEMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27Shock
IEC60068-2-32
IEC60068-2-6Vibration
Free Fall
Warranty
5 years
-40to70C(-40to158F)
oo
Amber:IndicatePWR1orPWR2failure
Fault indicator
Fault Contact
Relay Relay output to carry capacity of 1A at 24 VDC
Power
Redundant Input power
Power consumption(Typ.) 6.4W (power device not included)
Overload current protection
Reverse polarity protection
Present
Present
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH)
Weight (g) 410 g
Dual DC inputs 12-48VDC on 6-pin terminal block
26.1(W)x94.9(D)x144.3(H)mm(1.03x3.74x5.68inches)
10/100/1000Base-T(X) RJ45
port indicator
Green for port Link/Act.
Amber for 100Mbps indicator
EN60950-1Safety
Relay Output DIP-Switch
Power-1failedwarning:(ON)enable,(OFF)disableDIP-Switch 1
Power-2failedwarning:(ON)enable,(OFF)disable
DIP-Switch 2
Processing Store-and-Forward
100/1000Base-X SFP port 2
Green for port Link/Act.
100/1000Base-X SFP port indicator
SFP Speed DIP-Switch
IGS-1042GPA
10/100/1000T
3
4
1
2
5
PW1 PW2 Fault
6
1000M 100M
P5 P6
100/1000X
6
5
SFP Link/Act LED
Amber: 100Mbps indicator
Green: Port Link/Act
100/1000Base-X SFP Port
DIP Switch Select
Gigabit LAN Port
Power LED
Power Fault LED
Frame Ground
PWR-1PWR-2
V2-V2+ V1-V1+
G
1A@24V DC 12-48V
Power
Supply
12-48 VDC
V+
V-
Warning
Device
GND+24V
V+
V-
DIP Switch Select for
Power Alarm Relay Output
Power
Supply
12-48 VDC
Power
Supply
DIP-2
OFF
OFF
ON
DIP-1
Power failure relay alarm disabled
PWR-1 failure, alarm enabledrelay
PWR-2 failure, alarm enabledrelay
DIP Switch Function
OFF
ON
OFF
Description
ON PWR-1 or PWR-2 failure,
alarm enabledrelay
ON
GIGABIT
INDUSTRIAL
SWITCH
Industrial Unmanaged Gigabit Switch
DIP-2
OFF
DIP-1
1000Mbps
DIP Switch Function
(SFP speed Selection)
Description
ON 100Mbps
DIP-Switch (ON) : SFP speed setting to 100Mbps
DIP-Switch (OFF) : SFP speed setting to 1000Mbps
DIP-Switch 1/2 (port 6/5)
port 5port 6
