ORiNG RGS-R9004GP+ME-HV User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
RGS-R9004GP+ME-HV
Q I G RGS-R9004GP+ME-HV 1907-200-RR9004+MH1-FX010
RGS-R9004GP+ME-HV is Layer-3 modular managed redundant ring Ethernet
switch with 6 slots, up to 48 ports, and has 4 fixed 10G SFP+ ports. With such
high port density and modular design, it makes network planning easier. With
completely support of Ethernet Redundancy protocol, O-Ring (recovery time
< 30ms) and MSTP (RSTP/STP compatible) can protect your mission-critical
applications from network interruptions or temporary malfunctions with its fast
recovery technology. And support wide operating temperature from 0 C to
o
60 C. can also be managed centralized and convenient
oRGS-R9004GP+ME
by Open-Vision, as well as the Web-based interface, Telnet and console (CLI)
configuration. Therefore, the switch is one of the most reliable choice for
highly-managed and Fiber Ethernet.
M A N A G E D
Rack-Mount
G I G A B I T
S W I T C H
Panel Layouts
1
9
12
1. Power input module slots
2. Terminal block
Package Contents
Front View
Rear View
Network Connection
Console cable
To connect the console port to an external
management device, you need an RJ-45
to DB-9 cable, which is also included in
the package. Please see the table for the
console port pin assignment information.
Cable Types and Specifications:
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE-T Cat. 5 / Cat. 5e 100-ohm UTP UTP 100 m (328 ft) RJ-45
The series have standard Ethernet ports. According to the link type, the switch uses CAT 3, 4, 5, 5e
UTP cables to connect to any other network devices (PCs, servers, switches, routers, or hubs).
Please refer to the following table for cable specifications.
1000 Base-T RJ-45
Pin Number
Assignment
1 BI_DA+
2 BI_DA-
3 BI_DB+
4 BI_DC+
5 BI_DC-
6 BI_DB-
7 BI_DD+
8 BI_DD-
10/100 Base-T(X) MDI/MDI-X
Pin Number
MDI port
MDI-X port
1 TD+(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit)
4 Not used Not used
5 Not used Not used
6 RD-(receive) TD-(transmit)
7 Not used Not used
8 Not used Not used
10/100 Base-T(X) RJ-45
Pin Number
Assignment
1 TD+
2 TD-
3 RD+
4 Not used
5 Not used
6 RD-
7 Not used
8 Not used
1000Base-T MDI/MDI-X
Pin Number MDI port MDI-X port
1 BI_DA+ BI_DB+
2 BI_DA- BI_DB-
3 BI_DB+ BI_DA+
4 BI_DC+ BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7 BI_DD+ BI_DC+
8 BI_DD- BI_DC-
RS-232 baud rate setting: 9600, 8, N, 1
With 10/100BASE-T(X) cables, pins 1 and 2 are used for transmitting data. and pins 3 and 6
are used for receiving data. The device also supports auto MDI/MDI-X operation. You can use
a cable to connect the switch to a PC.
For pin assignments for different types of cables, please refer to the following tables.
PC pin out (male)
assignment
RS-232 with DB9
female connector
DB9 to RJ 45
Pin #2 RD Pin #2 TD Pin #2
Pin #3 TD Pin #3 RD Pin #3
Pin #5 GND Pin #5 GND Pin #5
Dimension Unit =mm (Tolerance ±0.5mm)
Contents
CD
RGS-R9004GP+ME-HV
Pictures Number
X 1
X 1
The device is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
QIG
Console Cable
X 2
X 1
X 1
Rack-mount Kit
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient: If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Mechanical Loading: Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Safety & Warnings
Industrial Layer 3 modular rack mount
Managed Gigabit Switch
LAYER 3
Circuit Overloading: Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on overcurrent protection
and supply wiring. Appropriate consideration of equipment nameplate ratings should be used
when addressing this concern.
External metal parts of this equipment are extremely hot!! Before touching the equipment, be
sure to protect your hands and body from serious injury.
654321
4 3 2 1
10G SFP+
Module
Fault
Reset
Console
115200,8 ,N,1
RingR.M.
2
PWR 1
RGS-R 9004GP+M E
88.00
654321
4 3 2 1
10G SFP +
Modul e
Fault
Reset
Consol e
115200 ,8,N,1
RingR.M.
2
PWR 1
RGS- R9004G P+ME
2 3 4 5 6 7 8
10
11
1. Power LED
2. Power2 LED
3. Power1 LED
4. R.M. status LED
5. Ring status LED
6. Faulty relay indicator
7. Reset button
8. Console port
9. Module status LEDs
10. 1G/10GBase-X SFP+ ports
11. Link/Act LED for SFP+ ports
12. Ethernet module slots
1
2
Installation
Rack-mounting
Step 1: Install left and right front mounting brackets to the switch using 6 M3 screws on each side
provided with switch.
Step 2: With front brackets orientated in front of the rack, nest front and rear brackets
together. Fasten together using remaining M4 screws into counter sunk holes.
Step 3: Fasten the front mounting bracket to the front of the rack.

Q I G Quick Installation Guide
PRINTED ON RECYCLED PAPER
Version 1.0
Quick Installation Guide
1. Launch the Internet Explorer and type in IP address of the switch. The default static IP
address is 192.168.10.1
2. Log in with default user name and password (both are ). After logging in, youadmin
should see the following screen. For more information on configurations, please refer
to the user manual. For information on operating the switch using ORing’s Open-Vision
management utility, please go to ORing website.
Specifications
ORing Swi tch Model
Physica l Ports
Technol ogy
Ethernet Standards
Slot Number
RS-232 Serial Console Port
Sw it ch Properties
Security Fea tures
Device Binding security featu re
Enable/disable ports, M AC b as ed port security
Port b as ed n etwork access control (80 2. 1x )
MAC- ba se d authentication (802.1 x)
VLAN (802.1Q) to segregat e an d se cure network traffic
Radi us c entral ized password management
SNMPv3 encrypted authen ti ca tion and access security
Https / SSH enhance network secur it y
Web and CLI authenti ca ti on and authorization
IP source guard
Software Fea tu res
Hardware routing, RIP , VRRP and st at ic r outing
IEEE 802.1D Bridge, auto MA C ad dr ess learning/aging and MAC ad dr ess (static)
Multiple Registration Protocol (MRP)
MSTP (RSTP/STP compatib le )
Redu nd an t Ring (O-Ring) with recovery time le ss t ha n 30ms
TOS/ Di ff serv supported
Quality of Service (802.1p) for r ea l-time tra ffic
VLAN (802.1Q) with VLAN taggi ng
IGMP v2/v3 Snooping
Application-based QoS m an ag ement
DOS/DDOS auto prevention
Port c on fi gura ti on, status, statistics, m on it oring, security
DHCP Server/Client/Relay
Modbus TCP
SMTP Client
NTP server
Network Re dundancy
O-Ring
O-Chain
MRP*NOTE
MSTP (RSTP/STP compatib le )
RS-232 in RJ45 connector wi th c on sole cable. 1 15 200bps, 8 , N, 1
RGS-R90 04GP+ME-HV
6
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 1 00 Ba se-FX
IEEE 802.3ab for 1000Base -T
IEEE 802.3z for 1000Base-X
IEEE 802.3x for Flow contro l
IEEE 802.3ad for LACP (Link Agg re gation Control Protocol )
IEEE 802.1p for COS (Class of S er vi ce)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol )
IEEE 802.1s for MSTP (Multi pl e Sp anning Tree Protocol)
IEEE 802.1x for Authenticat io n
IEEE 802.1AB for LLDP (Link Layer Discovery Pro to col
Sw it ch latency: 7 us
Sw it ch bandwidth: 176Gbps
Max. Number of Ava il ab le VLANs: 4095
IGMP multicast groups: 12 8 fo r ea ch VLAN
Port rate limiti ng : User Define
MAC Table 32K
Processing Store-and-Forward
Priority Queues 8
Jumbo frame Up to 9K Bytes
Power
Environ mental
-40 to 85 C (-40 to 185 F )
o o
Storag e Temperature
Operat ing Temperature
Physica l Characterist ic
Dimension (W x D x H)
Weight (g) 5.7 kg (without module)
5% to 95% Non-condensing
Operat ing Humidity
Regulat ory Approvals
Enclosure 2U 19 inches rack mountab le , IP -30
444.5 (W) x 422 (D) x 86.2 (H) mm (17.4 9 x 16 .6 1 x 3.39 inches)
EN 55032, CISPR32, EN 6100- 3- 2, E N 6100-3-3, FCC Part 15B class AEMI
EN 55024 (IEC/EN 61000-4- 2 (E SD ), IEC/EN 61000-4-3 (RS), I EC /EN 61000-4-4 (EFT) ,
IEC/EN 61000-4-5 (Surge ), I EC /EN 61000-4-6 (CS), IEC/E N 61 000-4-8 (PFMF), IEC/EN 61 00 0- 4-11 (DIP))
EMS
IEC60068-2-27Shock
IEC 60068-2-31
IEC60068-2-6Vibrat ion
EN60950-1 Safety
Free Fall
Warrant y
5 ye ar s
0 to 60 C (32 to 140 F)
o o
Packet Buf fe r 32Mbits
Flash Memory 128Mbits
DRAM Size
512MB
CE EMC (EN 55024, EN 55032), FC C Part 15 B
EMC
MTBF
412139 hours
NOTE: This function is available by request only
ORing Industrial Networking Corp.
Copyright© 2019 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oringnet.com
E-mail: [e-mail]
Optional Module
SWM-80GT-E SWM-08GP-E SWM-44GTP-E
Configurations
Wiring
Grounding
Grounding and wire routing to help limit the effects of noise due to electromagnetic
interference (EMI). Run the ground connection from the ground screws to the grounding
surface prior to connecting devices.
Power inputs
RGS-R900 4GP+ME-HV supports dual 100~240VAC/125-370VDC
power inputs, Power Supply 1 (PWR1) and Power Supply 2 (PWR2).
The connections for PWR1 and PWR2 are located on the terminal
block.
STEP 1: Remove the transparent protective cover from the terminal block
STEP 2: Insert the negative/positive DC wires into the V-/V+ terminals, respectively.
STEP 3: To keep the DC wires from pulling loose, use a small flat-blade screwdriver to tighten
the wire-clamp screws on the front of the terminal block connector.
STEP4: After wiring is completed, put the transparent cover back to the terminal block.
After installing the switch card, the green power LED should turn on. Please
refer to the following tablet for LED indication.
LED
Color
Status
Description
PWR Green On System ready
Blinking Upgrading firmware
PWR1 Green On AC power module1 activated
PWR2 Green On AC power module2 activated
R.M Green On System running in Ring Master mode
Ring Green On System running in Ring mode
Blinking Ring structure is broken
Fault Amber On Unexpected event occurred
Module Green On Module slot is connected
1G/10GBase-X SFP+ ports
LNK/ACT Green On Port is connected
Blinking Transmitting data
To reboot the switch, press the button for 3 seconds.Reset
To restore the switch configurations back to the factory defaults, press the button for 5Reset
seconds.
Resetting
1G/10Gbase-X w ith SFP+ 4
Powe r co ns umption(Typ .) 68.8W
Overload current protection Pr es en t
Overload current protection Du al 1 00 ~240VAC/ 12 5-370VDC power inputs at term in al block
Reverse Polarity Prote ct io n Present
RGS-R9004GP+ME-HV
Q I G RGS-R9004GP+ME-HV
M A N A G E D
Rack-Mount
G I G A B I T
S W I T C H
Industrial Layer 3 modular rack mount
Managed Gigabit Switch
LAYER 3