Otto Bock C1000 SF User manual

C1000 SF
Instructions for use (user) ...................................................................................... 3

Additional options
Prior to delivery of the power wheelchair, the qualified personnel must tick the additional options mentioned in the
following if they are present on the power wheelchair.
The power wheelchair can be equipped with the following additional options:
Electronic drive-away lock*
[ ] Function enabled [ ] Function disabled
If enabled, the function is activated by pressing the mode button on the control panel.
The function is deactivated with the joystick.
Electronic steering lock*
[ ] Function enabled [ ] Function disabled
The electronic steering lock is turned on or off with the following button when the motors are at standstill and the
spring-loaded brakes are engaged:
[ ] Warning flasher
2-way adapter cable*
[ ] Adapter cable included [ ] Adapter cable not included
The included adapter cable allows the following functions to be selected directly through separate buttons:
[ ] Stand-up device [ ] Back angle adjustment [ ] Seat tilt
[ ] Direction indicator, right [ ] Direction indicator, left [ ] Warning flasher
[ ] Light [ ] Horn [ ] Other:
[ ] S1: Stand-up function [ ] S2: Tilt function [ ] S3: Prone function (half-prone
position)
*See the section "Use" for more information.
2 C1000 SF

Foreword1 6..............................................................................................................................................................
Product description2 6............................................................................................................................................
Function2.1 6..............................................................................................................................................
Product overview2.2 7..................................................................................................................................
Safety3 8....................................................................................................................................................................
Explanation of warning symbols3.1 8..............................................................................................................
General safety instructions3.2 8.....................................................................................................................
Effects of electromagnetic interference on the product and on the user3.3 9........................................................
Nameplate and warning labels3.4 10..............................................................................................................
Signage on the product3.4.1 10.......................................................................................................................
Nameplate3.4.2 10..........................................................................................................................................
Warning labels3.4.3 11...................................................................................................................................
Delivery4 11...............................................................................................................................................................
Scope of delivery4.1 11................................................................................................................................
Options4.2 11.............................................................................................................................................
Storage4.3 11..............................................................................................................................................
Storage during daily use4.3.1 11......................................................................................................................
Storage during extended disuse4.3.2 11............................................................................................................
Preparation for use5 12...........................................................................................................................................
Safety instructions5.1 12...............................................................................................................................
Initial operation5.2 12...................................................................................................................................
Settings5.3 13.............................................................................................................................................
Changing control unit parameters5.3.1 13.........................................................................................................
Use6 13......................................................................................................................................................................
Circuit breaker6.1 13...................................................................................................................................
Armrests6.2 13............................................................................................................................................
Folding away the arm supports6.2.1 13.............................................................................................................
Footplate6.3 14...........................................................................................................................................
Backrest6.4 14............................................................................................................................................
Folding the backrest up/down6.4.1 14..............................................................................................................
Getting in and transferring6.5 15...................................................................................................................
Belts/belt systems6.6 16...............................................................................................................................
Safety instructions6.6.1 16...............................................................................................................................
Lap belt6.6.2 17.............................................................................................................................................
Adaptation6.6.2.1 17.........................................................................................................................................
Use6.6.2.2 17...................................................................................................................................................
Chest belt6.6.3 18..........................................................................................................................................
Adaptation6.6.3.1 18.........................................................................................................................................
Use6.6.3.2 19...................................................................................................................................................
Knee pad6.6.4 19...........................................................................................................................................
Adaptation6.6.4.1 19.........................................................................................................................................
Use6.6.4.2 20...................................................................................................................................................
Cleaning6.6.5 20............................................................................................................................................
Control unit6.7 21........................................................................................................................................
Control panel6.7.1 21.....................................................................................................................................
Buttons and display functions6.7.2 21...............................................................................................................
Driving functions6.8 23.................................................................................................................................
Safety instructions6.8.1 23...............................................................................................................................
Driving notes6.8.2 25......................................................................................................................................
Switching on and off6.8.3 27............................................................................................................................
Selecting the speed levels6.8.4 27....................................................................................................................
Driving6.8.5 27...............................................................................................................................................
Range6.8.6 28................................................................................................................................................
Table of contents
3C1000 SF
Table of contents

Drive-away lock6.8.7 28...................................................................................................................................
Steering lock6.8.8 29......................................................................................................................................
Adjusting the driving characteristics6.8.9 30......................................................................................................
Enabling/disabling the brakes6.9 30...............................................................................................................
Batteries/charging process6.10 31..................................................................................................................
Safety instructions6.10.1 31...............................................................................................................................
General6.10.2 31.............................................................................................................................................
Battery charging information6.10.3 32.................................................................................................................
Battery charger6.10.4 32...................................................................................................................................
Charging the battery6.10.5 32............................................................................................................................
Seat6.11 34..................................................................................................................................................
Safety instructions6.11.1 34...............................................................................................................................
Seat type6.11.2 34...........................................................................................................................................
Headrest6.11.3 34............................................................................................................................................
Power seat functions6.12 34...........................................................................................................................
Safety instructions6.12.1 35...............................................................................................................................
Electric stand-up function6.12.2 36.....................................................................................................................
Important instructions for use6.12.2.1 37...............................................................................................................
Emergency lowering device6.12.2.2 37..................................................................................................................
Power seat tilt6.12.3 37.....................................................................................................................................
Power back angle adjustment6.12.4 38...............................................................................................................
Power elevating legrest with automatic length adjustment6.12.5 38........................................................................
Power lowering footplate6.12.6 39......................................................................................................................
Power prone functions6.12.7 39.........................................................................................................................
Controlling power seat functions6.12.8 40...........................................................................................................
Joystick functions6.12.9 41................................................................................................................................
Lighting6.13 41.............................................................................................................................................
Control unit accessories6.14 42......................................................................................................................
Separate LCD monitor6.14.1 42.........................................................................................................................
Control panel for attendant6.14.2 47...................................................................................................................
Attendant control6.14.3 47.................................................................................................................................
Push-button module6.14.4 48............................................................................................................................
Special controls6.14.5 50..................................................................................................................................
Adapter cable for Piko button6.14.6 50...............................................................................................................
Additional options6.15 50...............................................................................................................................
Four-way chest strap kit6.15.1 50.......................................................................................................................
Comfort knee pad6.15.2 50...............................................................................................................................
Control panel holder6.15.3 51............................................................................................................................
Adjusting the control panel position6.15.3.3 52.......................................................................................................
Luggage carrier6.15.4 52..................................................................................................................................
Overview of additional options6.15.5 53..............................................................................................................
Disassembly and transport6.16 53...................................................................................................................
Safety instructions6.16.1 53...............................................................................................................................
Reducing the transportation size6.16.2 53...........................................................................................................
Preparing for transport6.16.3 54.........................................................................................................................
Use in vehicles for transporting persons with reduced mobility6.17 54..................................................................
Required accessories6.17.1 55..........................................................................................................................
Using the product in the vehicle6.17.2 55............................................................................................................
Restrictions for use6.17.3 56.............................................................................................................................
Care6.18 57..................................................................................................................................................
Safety instructions6.18.1 57...............................................................................................................................
Cleaning6.18.2 57............................................................................................................................................
Disinfection6.18.3 57........................................................................................................................................
Maintenance and repair7 57...................................................................................................................................
Safety instructions7.1 57...............................................................................................................................
4 C1000 SF
Table of contents

Maintenance7.2 58.......................................................................................................................................
Maintenance intervals7.2.1 58..........................................................................................................................
Repair7.3 59...............................................................................................................................................
Replacing a defective bulb7.3.1 59...................................................................................................................
Replacing a battery7.3.2 59.............................................................................................................................
Troubleshooting7.4 59..................................................................................................................................
Types of notifications7.4.1 59...........................................................................................................................
Wheelchair control unit error overview7.4.2 60...................................................................................................
Attendant control error overview7.4.3 61............................................................................................................
Behaviour in case of breakdowns7.5 62..........................................................................................................
Disposal8 62.............................................................................................................................................................
Safety instructions8.1 62...............................................................................................................................
Disposal information8.2 62............................................................................................................................
Legal information9 62..............................................................................................................................................
Liability9.1 62..............................................................................................................................................
CE conformity9.2 62.....................................................................................................................................
Warranty9.3 62............................................................................................................................................
Service life9.4 62.........................................................................................................................................
Technical data10 63...................................................................................................................................................
Appendices11 65........................................................................................................................................................
Threshold values for wheelchairs transportable by train11.1 65...........................................................................
5C1000 SF
Table of contents

1 Foreword
INFORMATION
Last update: 2017-11-01
►Please read this document carefully before using the product.
►Follow the safety instructions to avoid injuries and damage to the product.
►Have yourself instructed by qualified personnel in the proper and safe use of the product.
►Please keep this document in a safe place.
INFORMATION
►New information regarding product safety and product recalls can be obtained from the Customer Care Cen
ter (CCC) at [email protected] or from the manufacturer's service department (see inside back cover or back
page for addresses).
►You can request this document as a PDF file from the Customer Care Center (CCC) at [email protected] or
from the manufacturer's service department (see inside back cover or back page for addresses). It is possible
to increase the display size of the PDF document.
►For further questions about the instructions for use, please contact the qualified personnel who issued the
product to you.
You have purchased a high-quality product which can be put to versatile, daily use at home and outdoors.
In order to exclude injuries of any type, familiarise yourself with the handling, functions and use of the product
before using it. These instructions for use provide the necessary information.
Please note the following in particular:
• All users and/or their attendants must be trained by qualified personnel in the use of the product with the aid of
the instructions for use (user). In particular, the user(s) and/or attendant(s) must be informed of the residual
risk using the safety instructions in the instructions for use (user).
• The product has been adapted to the needs of the user. Further changes may be made only by qualified per
sonnel. We recommend checking the product settings regularly in order to assure an optimum fit over the long
term. For growing children and youths in particular, fitting should be performed every six months.
• In case of questions or problems, please consult the qualified personnel that adapted the product or the manu
facturer's service (see inside back cover or back page for addresses).
• Note the address and telephone number of the responsible qualified personnel/specialist dealer and keep this
information with you, especially when using your wheelchair outdoors. Inform the qualified personnel immedi
ately in case of a malfunction. Provide all relevant details to make quick assistance possible.
• The product may be combined only with the options listed here. The manufacturer assumes no liability for com
binations with third-party medical devices and/or accessories not included in the modular system. Please also
observe the information in the section "Liability".
• The operational safety of the product can only be ensured if it is used properly in accordance with the informa
tion contained in these instructions for use. The user is ultimately responsible for accident-free operation.
• Service and repairs to the product may only be carried out by qualified personnel. If you have any problems,
please contact your specialist dealer. This ensures that any necessary repairs will be made exclusively with
Ottobock spare parts.
• Your product may differ from the models shown. In particular, not all the options described in these instruc
tions for use will be installed on your product.
• The manufacturer reserves the right to make technical changes to the model described in these instructions for
use.
2 Product description
2.1 Function
The wheelchair is designed solely for individual use by persons who are unable to walk or who have a walking
impediment, and can be operated either by the patient or by another person.
The wheelchair can be used on solid ground both indoors and outdoors.
The powerful drive system with two 12 V gel batteries combined with spring-mounted drive wheels allows
obstacles to be crossed easily (Category B according to EN 12184) and offers safe operating performance.
6 C1000 SF
Foreword

The power wheelchair is controlled by the enAble50 wheelchair control unit (see Page21). The latter includes a
control panel to enter driving commands and display the current status as well as a controller that processes the
inputs and operates the drive motors and other electrical functions (see Page42).
The two caster wheels are controlled by separate steering motors. This considerably improves the driving charac
teristics, especially on uneven terrain or at higher speeds.
The special features of the power wheelchair include:
• Stand-up function that enables the user to assume a standing position.
• Individual control adaptation possibilities through programming and accessories.
• Modular structure that makes it possible to equip the power wheelchair with numerous options.
• Serviceability due to easy, straightforward access to all components.
2.2 Product overview
1
1 Back support 7 Foot support
2 Arm support (side panel) 8 Control panel with joystick
3 Seat cushion 9 Anti-tipper
4 Motor with brake release 10 Suspension
5 Caster wheel 11 Posterior lower leg support
6 Drive wheel
7C1000 SF
Product description

3 Safety
3.1 Explanation of warning symbols
WARNING Warning regarding possible serious risks of accident or injury.
CAUTION Warning regarding possible risks of accident or injury.
NOTICE Warning regarding possible technical damage.
3.2 General safety instructions
Hazards due to improper use of the product
WARNING
Improper product operation
Falling, tipping over, collision due to user error
►The product may only be used by a qualified user.
►As a user or attendant, you must be trained in the use of the product by qualified personnel instructed by the
manufacturer.
►Read the entire instructions for use.
►The product may not be used in case of exhaustion or under the influence of alcohol, medications or drugs.
►The product may not be used by users who have any mental limitations which can temporarily or permanently
limit attentiveness and judgement.
►You must observe road traffic regulations when driving in road traffic.
WARNING
Impermissible use
Risk of pinching, crushing, being pulled in, tipping, falling due to improper handling
►Only use this product for its original intended purpose.
►Only one person may be transported with the product at any one time.
WARNING
Overloading
Severe injuries if the product tips over due to overloading, damage to the product
►Do not exceed the maximum load capacity (see the nameplate and section "Technical data").
►Please note that certain options and add-on components will reduce the remaining load capacity.
WARNING
Exceeding the service life
Serious injuries due to failure to observe the manufacturer's requirements
►Using the product beyond the specified expected service life (see Page62) leads to increased residual risk
and should only take place subject to the due diligence and deliberations of qualified personnel.
►If the service life is reached, the user or a responsible attendant should contact the qualified personnel who
fitted the product or the manufacturer's servicing department (see inside rear cover or back page for
address). Here the user can obtain information about known risks and the current options for refurbishing the
product.
CAUTION
Extreme temperatures
Hypothermia or burns through contact with components, failure of components
►Do not expose the product to any extreme temperatures (e.g. direct sunlight, sauna, extreme cold).
NOTICE
Use under incorrect environmental conditions
Damage to the product due to excessively high or low temperatures
►Only use the product within a temperature range of -15°C to +40°C (5°F to +104°F).
8
Safety
C1000 SF

3.3 Effects of electromagnetic interference on the product and on the user
CAUTION
Use of mobile devices with electromagnetic emissions (e.g., mobile phones)
Falling, collision with persons or objects due to interference with the control signals
►Turn all mobile devices off while driving, since the driving characteristics of the product are affected by elec
tromagnetic fields.
►Turn the control unit off when it is not required, since the product may generate electromagnetic fields that
can cause interference with other devices. The product has been tested according to EMC regulations.
►Notwithstanding compliance with all applicable EMC directives and standards, the product can be affected by
interference from other electric devices (e.g., department store EAS systems) or cause interference with such
devices. If this occurs, move your product outside the interference range.
• Powered wheelchairs may be susceptible to electromagnetic interference (EMI), which is interfering electro
magnetic energy (EM) emitted from sources such as radio stations, TV stations, amateur radio (HAM) transmit
ters, two-way radios, and cellular phones.
• The interference (from radio wave sources) can cause the powered wheelchair to release its brakes, move by
itself, or move in unintended directions.
• It can also permanently damage the powered wheelchairs control system.
• Because EM energy rapidly becomes more intense as one move closer to the transmitting antenna (source),
the EM fields from hand-held radio wave sources (transceivers) are of special concern. It is possible to uninten
tionally bring high levels of EM energy very close to the powered wheelchair's control system while using these
devices. This can affect powered wheelchair movement and braking.
• Other types of hand-held devices, such as cordless phones, laptop computers, AM/FM radios, TV sets, CD
players, and cassette players, and small appliances, such as electric shavers and hair dryers, so far as we
know, are not likely to cause EMI problems to your powered wheelchair.
9C1000 SF
Safety

3.4 Nameplate and warning labels
3.4.1 Signage on the product
The warning signs and nameplates are attached at the following mounting points to the power wheelchair:
2
3.4.2 Nameplate
Label Meaning
AType designation
BRead the instructions for use before using the product.
Observe safety information in the instructions for use
CSymbol for separate collection of electrical and electronic
devices. Components of the power wheelchair and batteries
may not be disposed of in household waste.
DEuropean article number (EAN)
EProduct reference number
FSerial number*
GMaximum load (see section "Technical data")
HMaximum climbing ability (see section "Technical data")
IMaximum speed (see section "Technical data")
JAllowable axle load, front
KAllowable axle load, rear
LPermissible overall weight
MManufacturer information/address
NCE marking – product safety in accordance with EU directives
The nameplate is located on the side of the
frame below the seat.
OManufacturing date**
* VVV = version; S = speed code; YY = year of manufacture; WW = week of manufacture; PP = production site;
XXX = sequential production number
** YYYY = year of manufacture; MM = month of manufacture; DD = day of manufacture
10
Safety
C1000 SF

3.4.3 Warning labels
Label Meaning
APower driving mode: lock motor brake
BManual driving mode: unlock motor brake
Risk of pinching. Do not reach into the danger area.
(Only in case of installation of ISO sets according to ISO
7176)
Fixation point/eyebolt to attach the product in vehicles for trans
porting persons with reduced mobility
4 Delivery
4.1 Scope of delivery
The power wheelchair is normally shipped fully assembled and fitted to the personal requirements of the respective
user.
The scope of delivery includes:
• Fitted power wheelchair with main components
• Installed options
• Battery charger
• Instructions for use (user)
4.2 Options
The standard model can be fitted to the user's personal requirements thanks to a large range of options.
A full list of the available modules and accessories is shown on the order form and in the accessories catalogue.
To use options: see Page13 et. seq.
4.3 Storage
4.3.1 Storage during daily use
The power wheelchair should always be protected against external influences.
The control unit must be turned off.
4.3.2 Storage during extended disuse
NOTICE
Deep discharge
Battery damage due to standby current
►Deactivate the circuit breaker if the wheelchair is not used for more than 3 days.
►To deactivate the circuit breaker: see Page13
Please observe the following if the power wheelchair is not used for more than 3days:
Storage conditions
• Maintain an ambient temperature between -15°C and +40°C (5°F and +104°F) and relative humidity
between 45% and 85%.
• Store the power wheelchair in a dry, enclosed room with sufficient air circulation and protection from external
influences.
• Protect the wheels against ground frost, e.g.by relieving them completely through assembly blocks or wooden
boards.
11C1000 SF
Delivery

• Maintain sufficient clearance from sources of heat. If the product is parked for an extended period of time or
the tyres overheat (e.g.in the vicinity of radiators or in case of exposure to strong sunlight behind glass), the
tyres may become permanently deformed.
• Fill pneumatic tyres with slight overpressure.
• Rotate the wheels weekly to prevent flat tyres from extended standing.
• For extended storage, store the power wheelchair so the wheels are not in contact with the ground.
Note regarding the tyres
• If the power wheelchair is not moved for several days, permanent colour changes may occur where the wheel
chair comes into contact with the surface it is standing on. Therefore a suitable mat should be used when park
ing it for extended periods of time.
• Tyres contain chemical substances that can react with other chemical substances (such as cleaning agents,
acids, etc.).
• Black tyres contain soot particles. They may leave black marks where they come into contact with the ground.
Therefore the manufacturer recommends grey tyres if the wheelchair is primarily used indoors.
• Avoid unnecessary parking outdoors. Direct exposure to sunlight/UV radiation causes the tyres to age more
quickly. As a result, the tread surface hardens and corner pieces break out of the tread.
• The tyres must be changed when the tread is less than 1mm (0.04") to ensure safe driving behaviour.
• The tyres should be replaced every 2years regardless of wear and tear.
• When power wheelchairs with PU tyres are parked for long periods, the tyres may become deformed (flat
spots). This deformation will go away on its own over time while driving.
5 Preparation for use
5.1 Safety instructions
WARNING
Improper handling of packaging materials
Risk of suffocation due to neglect of the duty to supervise
►Packaging materials must be kept out of the reach of children.
WARNING
Uncontrolled movement of components when making adjustments
Crushing, pinching, blows due to non-observance of the maintenance and repair instructions
►Ensure that body parts, such as hands or head, are never in the danger zone.
►Perform the work with the aid of a helper for support.
WARNING
Independent modification of settings
Serious injuries to the user due to unallowable changes to the product
►Do not modify the settings established by the qualified personnel.
►In case of problems with the settings (unsatisfactory seating position, caster wheel wobble, etc.) please con
tact the qualified personnel who adjusted your product.
CAUTION
Screw connections not tightened
Pinching, crushing, tipping over, falling of user due to assembly errors
►After all adjusting/readjusting work authorised by the manufacturer, retighten the mounting screws/nuts firmly.
Observe any torque settings which may be specified.
5.2 Initial operation
The specialist dealer ships the power wheelchair fully assembled and ready to use.
The following additional tasks may be required:
• Adjusting the settings (see next section)
• Activating the circuit breaker (see Page13)
• Folding up the backrest (see Page14)
12
Preparation for use
C1000 SF

• Charging the battery (see Page32)
5.3 Settings
The user may only perform the fine-tuning adjustments described in the following.
This fine-tuning should be carried out by attendants and only in the presence of the user. The user should sit
upright in the power wheelchair while adjustments are made.
• Adjusting the position of the control panel (see Page52)
• Adjusting the belt lengths (see Page16)
• Adjusting the luggage carrier (see Page52)
Further adjustments may be made only by qualified personnel
All parts of the product should be cleaned thoroughly before adjustments are made.
5.3.1 Changing control unit parameters
WARNING
Incorrect configuration settings
Falling, tipping over, collision due to programming errors
►Programming may only be performed by qualified personnel trained by the manufacturer. The manufacturer of
the product and the control unit manufacturer are not liable in case of damage caused by programming which
was not performed properly and/or which was not adjusted properly according to the user's abilities.
If necessary, the qualified personnel can adapt the preprogrammed wheelchair control unit and options to the con
crete requirements of the user.
6 Use
6.1 Circuit breaker
INFORMATION
►Should the automatic circuit breaker deactivate repeatedly after activation for no discernible reason, contact
the qualified personnel.
►For shipping or when the power wheelchair is not being used for an extended period of time, the automatic
circuit breaker should be deactivated.
The automatic circuit breaker has to be activated before the power wheelchair can be switched on.
It is located under the seat between the drive wheels.
3Activating the circuit breaker
►Close the reset lever, which is at an angle (see
fig.3, item1).
→The reset lever engages and the circuit breaker is
activated.
Deactivating the circuit breaker
►Press the pushbutton until the reset lever flips up at
an angle (see fig.3, item2).
→The circuit breaker is deactivated.
6.2 Armrests
The armrests offer the user additional support for the forearms.
To make getting into the wheelchair easier, the armrests can be folded up.
6.2.1 Folding away the arm supports
The arm supports can be folded up if necessary to make getting in from the side easier.
13C1000 SF
Use

4Folding arm support away to the rear
1) Reach under the arm support.
2) Fold up the arm support (see fig.4).
Folding arm support back to the front
1) Reach under the arm support.
2) Fold down the arm support.
6.3 Footplate
CAUTION
Exposed pinch points
Crushing, pinching due to incorrect handling
►Do not reach into the danger area with your fingers when folding the footplate up or down.
The user's feet can be placed on the footplate.
To make getting into the wheelchair easier, the footplate can be folded up.
5Folding up the foot support
1) Pull the locking bolt (see fig.5, arrow).
2) Fold the foot support up (see fig.5, right).
Folding down the foot support
1) Pull the locking bolt.
2) Fold the foot support down.
6.4 Backrest
CAUTION
Exposed pinch points
Crushing, pinching due to incorrect handling
►Do not reach into the danger area with your fingers when folding the backrest up or down.
The backrest provides pressure redistribution and support for the upper body.
6.4.1 Folding the backrest up/down
The wheelchair may be delivered with the backrest folded down. It has to be folded up and secured prior to use.
14
Use
C1000 SF

6Folding up the back support
1) Fold up the arm supports.
2) Fold the back support up.
3) Insert the cotter pin (double spring cotter) (see
fig.6, left).
4) Push the release button and engage the back sup
port strap in the back support strap lock (see fig.6,
right).
If needed: Tighten the belt first. In order to do so,
pull the back support up on the cross tube.
5) Fold down the arm supports.
Folding down the back support
1) Fold up the arm supports.
2) Release the tension of the strap on the rear of the
back support. In order to do so, pull the back sup
port up on the cross tube.
3) Push the release button and disengage the strap
from the back support strap lock (see fig.6, right).
4) Pull out the cotter pin (double spring cotter) (see
fig.6, left).
5) Fold the back support forward.
6.5 Getting in and transferring
CAUTION
Incorrect handling when getting in
Falling, tipping over due to incorrect handling
►Turn the control unit off while getting in and out, in order to avoid accidental driving.
►Always place the seat in a horizontal position.
►Note that the armrests are not capable of bearing full body weight, and therefore must not be used for getting
into or out of the wheelchair.
►Always put on a lap belt when driving.
The modular design of the power wheelchair and the ease with which you can swing away the armrests and pull off
the supports make it easy to get into and out of the wheelchair from/to the side or from/to the front.
Getting into and out of the wheelchair can be done by the user individually in a way that suits him or her best.
Getting in from the side
1) Bring the power wheelchair as close as possible to where the user is sitting.
2) Turn the control device off.
3) Swing one arm support to the rear (see Page13).
4) If needed: Pull out the supports (not illustrated).
5) Slide into the seat from the side. Using a transfer board can make side transfers easier.
6) Insert the supports and fold down the arm support.
Getting in from the front
CAUTION
Exposed pinch points
Crushing, pinching due to incorrect handling
►Do not reach into the danger area with your fingers when folding the footplate up or down.
INFORMATION
If the power wheelchair is equipped with the power lowering foot support, which is available as an option, this
function can make getting in easier as well. Further information: see Page39
15C1000 SF
Use

Because of the stand-up function, the foot support has been designed to be able to bear a maximum load of
136kg. It may therefore also be used for getting into or out of the wheelchair. The foot support is already adapted
to the user's requirements.
1) Turn the control device off.
2) If needed: Fold up the foot support (see Page14).
3) Have an attendant assist you or use a transfer lifter to get into and out of the power wheelchair.
4) If needed: Fold down the foot support.
6.6 Belts/belt systems
6.6.1 Safety instructions
Hazards during adjustment/adaptation
CAUTION
Improper adjustments
Injuries, malpositions, illness of the user due to adjustment changes
►The belt system is an important part of an individual seating unit/seating solution. Do not modify the installa
tion position and basic settings established by the qualified personnel.
►In case of problems with these adjustments (such as an unsatisfactory sitting position), promptly contact the
qualified personnel who fitted the product.
►Immediately consult the qualified personnel if you detect signs of discomfort or fear when using the product.
►Have the basic settings of the belt system checked regularly. Adjustments may be required due to the growth
of the user or because of changes in the course of the disease.
Hazards during application
WARNING
Improper use of the stand-up function
Throttling, suffocation or strangulation due to sliding forward in the product
►Always use the stand-up function with the lap belt, chest belt and knee pad applied.
CAUTION
Improper use
Falls, user falling out due to improper use
►Only open the belt system when the user is ready to get out of the product.
►Do not leave the user unsupervised if the cognitive abilities of the user could lead to unintentional opening of
the belt system.
CAUTION
Medical risks
Injuries, pressure sores due to application errors
►Regular measures for pressure redistribution and skin examinations are required. Should skin irritation and/or
skin reddening occur, consult the qualified personnel who adapted and adjusted the product. Do not continue
using the product without consultation.
Hazards during use in vehicles for transporting persons with reduced mobility
WARNING
Use of the belt system as a passenger restraint system in vehicles for transporting persons with reduced
mobility is forbidden
Serious injuries due to improper handling of the product
►Under no circumstances may the belts and positioning aids offered with the product be used as part of a pas
senger restraint system in vehicles for transporting persons with reduced mobility.
►Note that only the lap belt offered with the product may be used for additional stabilisation of the person sit
ting in a vehicle for transporting persons with reduced mobility.
►The chest belt and knee pad cannot be applied during transportation in a vehicle for transporting persons with
reduced mobility.
16
Use
C1000 SF

6.6.2 Lap belt
The lap belt provides additional stabilisation and prevents the user from sliding out of the seat.
6.6.2.1 Adaptation
Small length adjustments of the belt by the user or an attendant (e.g.for clothing of different thickness) are pos
sible.
The belt length can be adjusted on both sides. Excess belt length is taken up by the plastic slider.
60°
90°
7Positioning the user in the seat
• Place the user in an upright, 90° seated position (if
physiologically possible).
• Ensure that the back is up against the backrest pad
ding (if physiologically possible).
• The lap belt should be at an angle of about 60° to
90° to the seat surface and run in front of the pelvic
bone.
Possible positioning errors
• The lap belt is positioned above the pelvis of the user in the area of the soft part of the stomach.
• The user does not sit upright in the seat.
• If the lap belt is too loose, the user can shift/slide out to the front.
• During the installation/adjustment, the lap belt is routed over parts of the seating system (e.g.over armrests or
seat pads). This causes the lap belt to lose its retaining function.
8Adjusting the belt length
1) Position the user in the seat. Follow the positioning
instructions in the previous section to do so.
2) Close the belt.
3) Position the 2 halves of the buckle in front of the
upper body, centred over the thighs.
4) Position the respective half of the buckle at a right
angle (see fig.8, item 1).
5) Slide the 2 halves of the closure to the desired posi
tion.
6) Release the respective half of the buckle.
7) Verify the adjustment.
WARNING! The lap belt has to fit closely but
not too tightly so the user is not injured. It
should be possible to slide two fingers com
fortably between the strap and thigh.
6.6.2.2 Use
WARNING
Incorrect application
Throttling, suffocation or strangulation due to sliding forward in the product
►The lap belt must be put on when getting into the product and used at all times while using the product.
►Ensure that the buckle lies in the middle of the body.
►Remove any objects or clothing which get caught.
17C1000 SF
Use

9Applying the lap belt
>Prerequisite: Note the positioning instructions in
the previous section.
1) Push the 2 halves together until the buckle engages
with an audible click.
WARNING! The lap belt has to fit closely but
not too tightly so the user is not injured. It
should be possible to slide two fingers com
fortably between the strap and thigh.
2) Pull to check that it is secure.
Opening the lap belt
1) Press the release button.
2) Open the belt buckle and lay the belt to the side.
6.6.3 Chest belt
The chest belt stabilises and positions the upper body in relation to the backrest.
6.6.3.1 Adaptation
Small length adjustments of the belt by the user or an attendant (e.g.for clothing of different thickness) are pos
sible.
Positioning the user in the seat
• Place the user in an upright, 90° seated position.
• Ensure that the back is up against the backrest padding.
• The chest belt is intended to support the area over the sternum (breastbone) from the front. This is accom
plished when two fingers fit comfortably between the top of the belt and the armpit.
Possible positioning errors
• The user's hips are not secured with a separate lap belt (see Page17).
• If the positioning system is too loose, the user can shift forward/slide down.
• The positioning system collides with devices, accessories or supply hoses during installation and adjustment,
restricting their functionality.
• The positioning system makes contact above the user's sternum (too high) or in the area of the soft part of the
stomach (too low).
10 Changing the length of the chest belt
The width of the belt is changed by adjusting the length
of the left and right belt parts. Excess belt length is
taken up by the plastic slider.
1) Fasten the belt (see following section).
2) Lengthen or shorten the belt at the belt buckle.
3) Verify that the adjustment is correct.
WARNING! The chest belt is intended to sup
port the area over the sternum (breastbone)
from the front.
WARNING! Ensure that the chest belt lies
against the chest evenly on both sides and is
not too tight. It should be possible to slide two
fingers comfortably between the chest belt and
upper body.
18
Use
C1000 SF

6.6.3.2 Use
WARNING
Incorrect application
Throttling, suffocation or strangulation due to sliding forward/down in the product
►The chest belt must be put on when getting into the product and used at all times while using the product.
►Always use the chest belt in combination with a correctly applied and adapted lap belt to stabilise the pelvis.
►Ensure that the buckle lies in the middle of the body.
►Remove any objects or clothing which get caught.
CAUTION
Medical risks
Injuries, pressure sores due to application errors
►Regular measures for pressure redistribution and skin examinations are required. Should skin irritation and/or
skin reddening occur, consult the qualified personnel who adapted and adjusted the product. Do not continue
using the product without consultation.
11 Fastening the chest belt
> Note the positioning instructions in the previous
section.
1) Push the belt flap (see fig.11, item1) through the
wide eyelet (see fig.11, item2).
2) Position the belt pads in the middle of the body (see
fig.11, item3). Make sure that the belt pads do not
overlap to avoid pressure points.
3) Press down the hook-and-loop closure of the belt
flap to fasten it.
WARNING! The chest belt is intended to sup
port the area over the sternum (breastbone)
from the front. This is accomplished when two
fingers fit comfortably between the top of the
belt and the armpit.
WARNING! Ensure that the chest belt lies
against the chest evenly on both sides and is
not too tight. It should be possible to slide two
fingers comfortably between the chest belt and
upper body.
4) Pull to check that it is secure.
Opening the chest strap
1) Pull on the finger eyelet until the belt opens (see
fig.11, item4).
2) Pull the belt flap out of the wide eyelet (see fig.11,
item1/2). Lay the belt to the side.
6.6.4 Knee pad
The knee pad stabilises and secures the legs.
6.6.4.1 Adaptation
It is possible to make small adjustments to the spacing between the knee pad and lower leg (e.g.in case of cloth
ing of different thicknesses).
Positioning the user in the seat
• Place the user in an upright, 90° seated position.
• The legs have to be supported on the footplate and lie straight against the leg pad while sitting.
• Make sure that the lower leg length is adjusted correctly.
• The knee pad should lie flat on the lower legs below the knee caps.
Possible positioning errors
• The lower leg length is incorrectly adjusted.
19C1000 SF
Use

12 Adjusting the belt length
1) Use the belt buckles on the right and left sides of
the knee pad to shorten or lengthen the belt (see
fig.12, item1).
INFORMATION: The position of the belt knobs
for the knee pad cannot be changed.
2) Verify that the adjustment is correct.
WARNING! The knee pad should lie flat on the
lower legs below the knee caps. The legs must
be supported on the foot support. The knee pad
must press the calves firmly against the leg
pad, but not too tightly so the user is not
injured.
6.6.4.2 Use
13 Applying the knee pad
1) If needed: Open the belt tensioner on the knee pad
(see fig.13, item1).
2) Position the knee pad with the openings on the
legs.
3) Attach the eyelets of the knee pad belt to the two
belt knobs (see fig.13, item2).
4) Tighten the belt with the belt tensioner (see fig.13,
item1). Ensure that the belt tensioner snaps into
place audibly.
5) Pull to check that it is secure.
Opening the knee pad
1) Open the belt tensioner on the knee pad.
2) Disengage the knee pad belt from the two belt
knobs.
3) Set down the knee pad.
6.6.5 Cleaning
Cleaning a belt system with metal buckle
INFORMATION
Observe the washing recommendations on the product and the information in the corresponding instructions for
use provided for the product.
• Belts with metal snaps may not be washed in washing machines as the penetration of water could cause
corrosion and subsequent malfunctions.
• Clean the belt straps by gently dabbing them with warm soapy water (with some disinfectant) or carefully wiped
with a dry, clean, absorbent cloth.
Cleaning a belt system with plastic buckle
• Depending on the model, straps with plastic buckles can be washed in the washing machine between 40°C
and 60°C.
• Recommendation: Use a laundry bag or net and mild detergent.
INFORMATION
Alternatively, the belt straps can be cleaned by gently dabbing them with warm soapy water (with some disinfect
ant) or carefully wiped with a dry, clean, absorbent cloth.
Additional cleaning instructions
• Allow the belts to air dry. Ensure that the belts and pads are completely dry before installation.
• Do not expose the belts to direct heat (e.g.sunshine, stove or radiator).
• Do not iron or bleach the belts.
20
Use
C1000 SF